Download
Share
Print this page
Dynojet Power Commander V Installation Instructions
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Automobile Accessories
  5. Power commander V
  6. Installation instructions

Dynojet Power Commander V Installation Instructions

2013 arctic cat 700cc h1 atv
Hide thumbs Also See for Power Commander V:
1
2
3
4

Advertisement

Quick Links

Download this manual See also: Installation Instructions & Owner's Manual, Instruction and Installation Manual
2013 Arctic Cat 700cc H1 ATV
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
11-014
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
1
Posi-tap
2
Velcro strips
1
Alcohol swab
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2013 Arctic Cat 700cc H1 ATV - PCV - 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the Power Commander V and is the answer not in the manual?

Questions and answers

Related Manuals for Dynojet Power Commander V

Summary of Contents for Dynojet Power Commander V

  • Page 1 Installation Guide 2013 Arctic Cat 700cc H1 ATV Power Commander Decals I n s t a l l a t i o n I n s t r u c t i o n s Dynojet Decals Posi-tap Velcro strips Alcohol swab THE IGNITION MUST BE TURNED...
  • Page 2 POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Switch Input #2 by default.) SPEED INPUT 2 (Grnd) EXPANSION PORTS 1 & 2...
  • Page 3 FIG.A Remove the seat and left hand side panel shown in Figure A. FIG.B Remove Remove the storage cover shown in Figure B and the storage bin. Loosen the clamp from the throttle body and remove the air snorkel from the throttle body. To make the fuel injector more accessible, lift the snorkel/airbox upward away from the top of the engine. FIG.C Remove the two screws securing the tool kit to expose the battery. Using the supplied Velcro, secure the PCV under the seat at the location shown in Figure C. Clean both surfaces with the supplied alcohol swab before attaching the Ground Velcro. Route the PCV wiring harness under the frame spar toward the front of the machine. Attach the ground wire from the PCV to the negative (-) terminal of the battery. 11-014 www.powercommander.com 2013 Arctic Cat 700cc H1 ATV - PCV - 3...
  • Page 4 FIG.D Disconnect the stock wiring harness from the fuel injector (Fig. D). Unplug 10 Plug the PCV wiring harness in-line of the fuel injector and the stock wiring harness. FIG.E 11 Locate the Throttle Position Sensor (TPS) on the left hand side of the throttle body. 12 Using the supplied posi-tap, attach the GREY wire from the PCV to the stock GREEN/BLACK wire Posi-tap from the TPS. 13 Replace the storage bin, cover, tool kit, side panel, and seat. 11-014 www.powercommander.com 2013 Arctic Cat 700cc H1 ATV - PCV - 4...