Advertisement
Table of Contents
Voice Reach Talking Pendant
I.
Identifying the Parts
1
.
A
c
t
i
v
e
1
.
A
c
t
i
v
e
Press the Active Button once will activate the Control Panel, causing it to dial
emergency call or alarm. Once the button is pressed, the Green LED lights on for 3
sec and then becomes flashing to indicate alarm signal transmission to the Control
Panel is in progress. During signal transmission, the WTRVS will emit continuous
beeps.
When the Control Panel receives the signal from WTRVS, its red light will go on. It
will then dial the Central Monitoring Station and wait for command. Once the Central
Monitoring Station acknowledges the signal, a remote two-way voice communication
channel will be opened with the WTRVS.
When there is an incoming phone call, you can press the Active Button to answer it.
If the two way communication is enabled, WTRVS will stop emitting beeps. WTRVS
will open a remote two-way voice communication for 30 minutes.
To terminate both the reporting and the two-way communication, press and hold the
Active Button for 8 sec.
2
.
D
u
a
l
C
2
.
D
u
a
l
C
LED OFF: In Standby Mode
RED LED ON: Registering WTRVS to the Control Panel
RED & GREEN LED FLASH: Transmitting signal to the Control Panel
GREEN LED ON: Receives learning signal from the Control Panel
3
.
S
p
e
a
k
3
.
S
p
e
a
k
4
.
L
a
n
y
a
r
4
.
L
a
n
y
a
5
.
M
i
c
r
o
p
5
.
M
i
c
r
o
p
6
.
C
R
2
3
V
6
.
C
R
2
3
7
.
L
o
w
B
7
.
L
o
w
B
Press the Low Battery Detection button to test WTRVS's battery status while
WTRVS is in the stand by mode. If WTRVS emits 3 short beeps after pressing the
button, it indicates that WTRVS is in the low battery status. If not, it means WTRVS's
voltage is in the normal state.
If WTRVS is detected in the low battery status, when you press WTRVS to dial an
emergency call or alarm, the Red LED will go on for 3 seconds and WTRVS will emit
continuous raipd beeps.
You are not allowed to test the battery status during two-way communication mode
or the period of triggering the emergency alarm.
/
P
e
n
d
a
n
t
B
u
t
t
o
n
/
P
e
n
d
a
n
t
B
u
t
t
o
n
o
l
o
u
r
R
e
d
&
G
r
e
o
l
o
u
r
R
e
d
&
G
r
e
e
r
e
r
d
L
o
o
p
r
d
L
o
o
p
h
o
n
e
h
o
n
e
L
i
t
h
i
u
m
B
a
t
t
e
r
V
L
i
t
h
i
u
m
B
a
t
t
e
r
a
t
t
e
r
y
D
e
t
e
c
t
i
o
n
a
t
t
e
r
y
D
e
t
e
c
t
i
o
n
e
n
L
E
D
e
n
L
E
D
y
y
B
u
t
t
o
n
B
u
t
t
o
n
1
(
W
T
R
V
S
)
(
W
T
R
V
S
)
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Climax WTRVS
Summary of Contents for Climax WTRVS
- Page 1 If WTRVS is detected in the low battery status, when you press WTRVS to dial an emergency call or alarm, the Red LED will go on for 3 seconds and WTRVS will emit continuous raipd beeps.
- Page 2 It is prohibited to learn-in another or the same WTRVS twice, unless the previously learnt WTRVS is removed first. Step 4. To check if the WTRVS is successfully learnt in, enable the Control Panel to get into the Walk Test Mode first and press the WTRVS ACTIVE button. If you hear 6...
- Page 3 > < > It is prohibited to learn-in the WTRVS to the Control Panel when the WTRVS is in low battery status. You are not allowed to test the battery status during the two-way communication mode or the period of triggering emergency alarm.
- Page 4 Changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with FCC RF Radiation Exposure limits set forth for an uncontrolled Environment. This device must not be co-located or operated in conjunction with any other antenna or transmitter.
Need help?
Do you have a question about the WTRVS and is the answer not in the manual?
Questions and answers