Tait T2000 Installation Manual page 4

4 T2000 Installation Guide
error free. However Tait warrants that the diskettes if any on which the Software is supplied to the
Licencee shall be free from defects in material and workmanship under normal use and service for a
period of ninety (90) days from the date of delivery to the Licencee.
Exclusion of liability
Tait's entire liability and the Licencee's exclusive remedy shall be:
1. The replacement of any diskette not meeting Tait "limited warranty" and which is returned to
Tait or an authorised agent or subsidiary of Tait with a copy of the Licencee's purchase receipt;
or
2. If a diskette is supplied and if Tait is unable to deliver a replacement diskette which is free from
defects in material or workmanship, the Licencee may terminate this Agreement by returning
the Software to Tait.
3. In no circumstances shall Tait be under any liability to the Licencee, or any other person whatso-
ever, for any direct or consequential damage arising out of or in connection with any use or ina-
bility of using the Software.
4. Tait warrants the operation of the Software only with the operating system for which it was
designed. Use of the Software with an operating system other than that for which it was
designed may not be supported by Tait, unless otherwise expressly agreed by Tait.
General
The Licencee confirms that it shall comply with the provisions of law in relation to the Software.
Law and jurisdiction
This Agreement shall be subject to and construed in accordance with New Zealand law and dis-
putes between the parties concerning the provisions hereof shall be determined by the New Zea-
land Courts of Law. Provided however Tait may at its election bring proceedings for breach of the
terms hereof or for the enforcement of any judgement in relation to a breach of the terms hereof in
any jurisdiction Tait considers fit for the purpose of ensuring compliance with the terms hereof or
obtaining relief for breach of the terms hereof.
No Dealings
The Licencee may not sublicense, assign or transfer the licence or the program except as expressly
provided in this Agreement. Any attempt otherwise to sublicense, assign or transfer any of the
rights, duties or obligations hereunder is void.
No Other Terms
The Licencee acknowledges that it has read this agreement, understand it and agree to be bound by
its terms and conditions. The Licencee further agrees that this is the complete and exclusive state-
ment of the agreement between it and Tait in relation to the Software which supersedes any pro-
posal or prior agreement, oral or written and any other communications between the Licencee and
Tait relating to the Software. (LS-589)
1. Terminate one end of the coaxial cable at the antenna. Good quality 50 ohm coaxial cables such as
RG58 or UR76 are suitable. Run the free end of the coaxial cable to the radio's mounting position
and cut it to length allowing 200mm to 300mm excess.
2. Terminate the free end of the cable with the BNC crimp plug supplied, as shown in Figure 4:
Fit the crimp sleeve over the cable sheath.
Trim the outer sheath from the cable to 15mm.
Trim the braid to 8.5mm.
Trim the dielectric to 11mm. (Take extreme care not to 'nick' the centre conductor with the
trimming device).
Fit the male pin onto the centre conductor with the shoulder pressed against the
end of the dielectric.
Crimp the male pin onto the centre conductor.
Press the assembly firmly into the rear of the plug. (Check that no braid gets
trapped between the dielectric and the inside of the plug.)
Slide the crimp sleeve over the braid and press against the shoulder of the plug.
Crimp the crimp sleeve onto the braid and plug body.
Figure 4 Antenna Connector Assembly
Wiring
External Speaker
Some T2000II models are fitted with internal speakers. However it is possible to fit an external
speaker if required, by terminating a twin wire in the power connector. To disable the internal
speaker, cut the link on the power connector as shown in Figure 5.
T2000II models with no internal speaker must have an external speaker fitted. The power connector
comes pre-wired with the speaker cable.
Ignition
External
Power } +13.8V
Supply } Ground
Figure 5 Power Connector Wiring
Mount the external speaker in a convenient location close to the operator. Run the free end of the
speaker wire to the speaker, and connect it to the speaker plug.
T2000 Installation Guide 9
Internal Speaker Link
(cut to disable)
Ground } External
} Speaker
Live