Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Tait T2000 SERIES II
Summary of Contents for Tait T2000 SERIES II
- Page 1 T2000 T2000 SERIES INSTALLATION GUIDE...
- Page 3 Licence In consideration of the payment of the Licence Fee which forms part of the price you paid for products you acquired from Tait or its subsidiary or agent (the “products”) and our willingness to be bound by the terms of this agreement, Tait grants to you as Licencee the non-exclusive right to use the copy of a Tait software program included in the products, (the “Software”).
-
Page 5: Table Of Contents
Contents Components of the T2000 Radio Kit ......1 Recommended Installation Tools ......... 1 Installation of your Radio .......... 2 Installation Planning ............2 To Disassemble the Cradle ..........2 Mounting ................3 To Reassemble the Cradle ........... 3 Antenna Installation ............4 Wiring ................. -
Page 7: Radio Kit
Components of the T2000II Radio Kit The T2000 Radio kit includes the following parts: l T2000 Radio Unit l BNC Antenna Crimp Plug l Microphone l Cradle Keys (2) l Complete Cradle l Power Cable (5m) l 4 Ohm Speaker (not for internal speaker models) l Installation Kit: - Two-way hermaphroditic connector (1) - Socket receptacle (2) - 10A 12V Blade fuse (2) -
Page 8: Installation Of Your Radio
See the M2000 service manual, available from your Tait dealer, for details of this modification. Occupant’s Safety Check that the chosen locations for the radio and accessories do not endanger the vehicle occupants. -
Page 9: Mounting
2. Disassemble the cradle by placing it on a firm surface and applying pressure down on one of the middle ribs of the plastic side moulding with a screwdriver. This will release the ribs along this edge from the slots in the metal cover with which they mate. A similar approach will release the other edge of the metal cover which can now be lifted clear (as shown below). -
Page 10: Antenna Installation
2. Take the remaining metal cover and fit it over the exposed edges of the side mouldings, again taking care to align the ribs with the slots. Clip it securely home. Figure 3: Cradle Reassembly Antenna Installation 1. If the antenna is dependent on a ground-plane for its operation, it is recommended that it be installed in one of the positions shown below: *1=most preferred *4=least preferred... - Page 11 3. Mount the antenna in such a position that no part of the human body will normally be within 20cm of it for more than a few minutes while the radio is switched on, unless there is an intervening metal screen (e.g. a metal roof) at least 0.3m in area (e.g.
-
Page 12: Wiring
Wiring EXTERNAL SPEAKER EXTERNAL SPEAKER EXTERNAL SPEAKER EXTERNAL SPEAKER EXTERNAL SPEAKER Some T2000 models are fitted with internal speakers. However it is possible to fit an external speaker if so desired. A twin wire must be terminated in the power connector. To disable the internal speaker, cut the link on the power connector as shown overleaf. -
Page 13: External Wire (Horn/Hush/Emergency)
8A. (The radios will tolerate a supply voltage range of 10.8V to 16.0V). In vehicles with a 24V electrical system (e.g. many trucks), it is essential to provide a suitably rated 24/12V converter (e.g. Tait T2007) to isolate the radio from the battery and protect it against excessive voltages. -
Page 14: Microphone Clip
5. Make a call to another party on the radio (as described in the operating instructions). Tait Electronics has made every effort to ensure the accuracy of information in this manual. However, Tait Electronics reserves the right to update the radio and / or this manual with- out notice. - Page 16 GERMANY Tait Mobilfunk GmbH Phone : (49) (911) 96746-0 Fax : (49) (911) 96746-79 HONG KONG Tait Mobile Radio (Hong Kong) Ltd Phone : (852) 2369 3040 Fax : (852) 2369 3009 NEW ZEALAND Tait Communications Ltd Phone : (64) (3) 348-3301 Fax : (64) (3) 343-0558...