Safety instructions Warning against injuries and material damages: Like any other electrical device, a sewing machine can cause serious, even life-threatening injuries.To According to legislation, you as the user of an avoid this, and in order to work safely: electrical appliance are responsible for preventing possible accidents through safety-conscious •...
CONTENTS Name of parts ................... 3-4 Accessories ....................5 Before sewing (Power supply and sewing lamp).......... 6 Removing extension table................7 Free-arm sewing..................7 Winding the bobbin ..................8 Removing bobbin case and bobbin..............9 Inserting bobbin into bobbin case .............. 10 Inserting bobbin case into shuttle race............
BEFORE SEWING 1. Fit plug into the machine. Power supply / Power supply plug 2. Insert plug into the main socket. 3. Sewing speed can be varied by the Power supply foot control. If the supply cord that fixed with foot controller is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified...
REMOVING EXTENSION TABLE Hold the left end of the table and pull it out in direction of the arrow. FREE-ARM SEWING 1. This sewing machine can be used as a flat bed machine but easily converts to a free arm machine by removing the extension table.
WINDING THE BOBBIN 1. Release by pushing clutch button to bobbin and lock by pushing it to needle. 2. Push bobbin winder from left to right, then it starts winding. 3. Push bobbin winder from right to left and move clutch button to needle sign, then it starts sewing.
REMOVING BOBBIN CASE AND BOBBIN 1. Raise the needle to its highest position and open shuttle race cover. 2. Open the hinged latch of the bobbin case and pull the bobbin case out of the machine. Hinged latch 3. Release the latch and the bobbin will fall out easily.
INSERTING BOBBIN INTO BOBBIN CASE 1. Pull 5 cm of thread from bobbin and insert it into bobbin case as shown. 5 cm 2. Guide the end of thread into the Slot slot. 3. Pull the thread through the slot and Tension spring under the tension spring and draw out about 10 cm of thread.
INSERTING BOBBIN CASE INTO SHUTTLE RACE 1. Raise the needle to its highest Finger position. Pull the thread to the front, open the latch of the bobbin case and hold it. Hinged latch 2. Holding the latch open, place bobbin case onto the centre pin in the Insert shuttle and release latch.
THREADING UPPER THREAD Warning: Before contriving please adjust main control switch to (O). Pass the thread from A to H as shown. Twin needle threading. - 12 -...
DRAWING UP THE BOBBIN THREAD 1. Hold the upper thread with left hand, turn the hand wheel slowly towards you until the needle goes down and comes up. Then stop the hand wheel when the take up lever is at its highest position.
ADJUSTING THREAD TENSION Normal upper thread tension: 3 – 5 Correct Upper thread Fabric Upper thread tension may be adjusted Bobbin thread by turning the thread tension dial. Incorrect Inside of fabric Upper thread Lower thread tension can be increased by turning the screw of the bobbin case slightly to the right (clockwise).
CHANGING NEEDLE Warning: Before changing the pin please adjust main control switch to Needle clamp screw (O). 1. Raise the needle bar to its highest Tighten position. 2. Loosen needle clamp screw and remove the old needle. 3. With the flat side of the needle facing away from you, insert the needle as far up as it will go.
FABRIC-THREAD-NEEDLE-TABLE Please pay attention to the following list as a guide for sewing different types of fabric. Indication Fabric Thread Needle Length of Stitches of Upper Tension Straight stitch Stitch Length Stitch Dial width Dial Nylon 80 Cotton Light Tricot 60 S Fiber 70 (10) silk...
TO START SEWING Important hints: 1. Raise the take-up lever to its highest position before starting and after stopping sewing. 2. Hold both threads about 10 cms to the rear of the machine for the first two or three stitches. 3.
HOW TO FINISH STITCHES 1. Sew to the edge of seam. 2. Push the reverse button and sew in reverse for about 3-4 cms. 3. Raise needle into its highest position. 4. Lift the presser foot and pull the fabric out of the back of the machine.
STRAIGHT STITCH 1. This type of stitching is used most frequently. 2. The zigzag presser foot can be used for both straight and zigzag sewing. 3. For sewing light fabric, use a smaller stitch size. (Refer to page 17 for dial setting). ZIGZAG SEWING Pattern selector position Satin stitching can be used for sewing...
OVERCASTING Use these stitches for oversewing rough edges. STRAIGHT AND ZIGZAG STRETCH STITCHES Use this stitch with knitted, tricot or other stretchy fabrics. The stitch enables your seam to stretch without breaking the thread. - 23 -...
BLIND STITCH 1. Fold fabric as shown. 2. Finish the seam as shown. - 24 -...
Page 26
Adjust the width to obtain the correct seam. Wrong: Needle is not piercing edge to fold at all. Needle pierces the edge of fold too much. Correct seam. - 25 -...
BUTTON SEWING (Optional) Utilise the foot of sewing of buttons. (Use Darning plate see page 16) 1. Place the darning plate properly. 2. Place button presser foot in position and attach it firmly. 3. Place the button between presser foot and fabric and lower the presser foot.
ZIPPER SEWING Utilise the foot of closing zipper. Select straight stitch. 1. Zipper foot is designed to sew close to a raised edge, thus preventing sewing on zipper. 2. Place zipper foot in position and attach firmly. 3. Fold the fabric about 2 cm and place the fabric under foot.
ONE-STEP BUTTONHOLE SEWING Stitch width adjusting dial set between 3 & 5 Pattern selection dial select “ T ” (Buttonhole lever) See notes below Handwheel (Presser foot) Replace with buttonhole presser foot (Stitch length adjusting dial) Set length between 0.25 to 1 as indicator Steps to set up mode for B/H lever: This special one-step buttonhole needs to set up machine at correct “Starting”...
Page 30
Button slot Direction line Upper/lower thread Direction line Direction line Button adjuster 2. Move button adjuster forwards and place the button you wish to make a buttonhole for into the button slot at rear. Then slide the buttonhole adjuster backwards to secure the button in place.
HEMMING (Optional) 1. Raise the foot and the needle to its highest position. Replace the foot with 3 mm the picot foot. 2. Fold over the fabric edge by about 3 mm and place it under the foot. 1 mm Secure the folded edge with a few stitches.
EMBROIDERY (Use darning plate see page 16) Remove the presser foot and attach the darning plate. Lower feed dog and move the hooped fabric slowly in the desired direction until the fabric has been embroidered. QUILTER (Optional) 1. Slide the arm through the hole on top of the pressure foot holder.
MAINTENANCE Warning: Please always unplug the power plug before you change the bulb or perform maintenance work to the machine so that you prevent deadly peril and electric shock. 1. Raise needle to its highest position. 2. Take out the bobbin case. 3.
CHECKING PERFORMANCE PROBLEMS – TROUBLESHOOTING Problem Probable cause What to do Fabric does not - Feed dog down - Raise feed dog move - Stitch length dial in “0“ position - Set dial between 1 and 4 - Incorrect insertion of needle - Re-insert needle - Bent needle - Replace needle...