Starting A Warm Engine; Starting A Flooded Engine - Poulan Pro 530165221 Instruction Manual

Starter Handle
Primer Bulb
1. Set unit on a flat surface.
2. Move ON/OFF switch to the ON position.
3. Slowly press the primer bulb 6 times.
4. Move choke lever to FULL CHOKE by
aligning lever with position shown on de-
cal (see illustration below).
Choke
position
decal
5. Squeeze the throttle trigger fully and hold
through all remaining steps.
6. Pull starter rope handle sharply until en-
gine sounds as if it is trying to start, but do
not pull rope more than 6 times.
7. As soon as engine sounds as if it is trying
to start, move choke lever to HALF
CHOKE by aligning lever with position
shown on decal (see illustration below).
Choke
position
decal
8. Pull starter rope sharply until engine runs,
but no more than 6 pulls. If the engine
doesn't start after 6 pulls (at the HALF
CHOKE position), move the choke lever to
the FULL CHOKE position and press the
primer bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the starter
rope until the engine runs, but no more than
6 pulls. If the engine doesn't start, repeat
procedure 2 additional times.
engine still doesn't start, it is probably
flooded. Proceed to
FLOODED ENGINE.
9. Once the engine starts, allow it to run 10 se-
conds, then move the choke lever to OFF
CHOKE by aligning lever with position
shown on decal (see illustration below). Al-
low the unit to run for 30 more seconds at
OFF CHOKE before releasing the throttle
trigger.
NOTE:
in the OFF CHOKE position, move the
choke lever to the HALF CHOKE position
Choke
and pull the rope until engine runs, but no
Lever
more than 6 pulls.
Choke
position
Muffler
decal

STARTING A WARM ENGINE

1. Move ON/OFF switch to the ON position.
2. Move the choke lever to the HALF
CHOKE position.
3. Squeeze and hold the throttle trigger.
Keep throttle trigger fully squeezed until
the engine runs smoothly.
4. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
5. Allow engine to run 15 seconds, then
move the choke lever to the OFF CHOKE
position.
NOTE:
rope 5 more pulls. If engine still does not run, it
is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing
the choke lever in the OFF CHOKE position;
then, pull the rope to clear the engine of ex-
cess fuel. This could require pulling the starter
handle many times depending on how badly
the unit is flooded.
If the unit still doesn't start, refer to
TROUBLESHOOTING
1-800-554-6723.
OPERATING THE COUPLER
This model is equipped with a coupler which
enables optional attachments to be installed.
The optional attachments are:
Edger . . . . . . . . . . . . . . . . . . . . . . .
Cultivator
Blower . . . . . . . . . . . . . . . . . . . . . .
Brushcutter
WARNING:
connect spark plug before removing or instal-
ling attachments.
REMOVING PRUNER ATTACH-
MENT, LINE TRIMMER ATTACH-
MENT, OR OTHER OPTIONAL AT-
TACHMENTS
NOTE:
If
CAUTION:
tachments, place the unit on a flat surface for
STARTING A
stability.
1. Loosen the coupler by turning the knob
counterclockwise.
11
If engine dies with the choke lever
If engine has not started, pull starter
TABLE or
MODEL:
PP1000E
. . . . . . . . . . . . . . . . . . . . PP2000T
PP3000B
. . . . . . . . . . . . . . . . . . PP4000C
Always stop unit and dis-
When removing or installing at-
call