Microwave Drawer Controls; Display; Before First Use; Clock - Jenn-Air JMDFS24GS Use And Care Manual

This manual may cover several different models. The model you have purchased may have some or all of the features shown here. The
appearance of your particular model may differ slightly from the illustrations in this manual.

Display

When the microwave drawer is in use, the display shows cooking
power, quantities, weights, and/or prompts. When it is not in use,
the display shows the time of day.

Before First Use

When the microwave drawer is first plugged in, the message
"Enjoy your microwave touch clear and touch clock" will scroll in
the display. You will need to clear the message to set the clock.
Clear display:
1. Touch STOP/CLEAR.
If the prompt "Enjoy your microwave touch clear and touch clock"
appears at any other time, a power failure has occurred. Clear the
display, and reset the clock.
NOTE: The microwave drawer can be programmed with the
drawer open except when using Start/Add 1 Min.
This is a standard 12-hour clock (12:00-11:59).
To Set Clock:
1. Touch TIMER/CLOCK, then number pad 2.
2. Enter time in hours and minutes.
3. Touch TIMER/CLOCK again to complete the setting.
The Start control (Start/Add 1 Min) begins any cooking function.
If cooking is interrupted, touching START will resume the preset
non-sensor function.
NOTE: To avoid unintentional operation of the microwave drawer,
the Start control will work only if a cooking cycle has ended, the
drawer has been closed or Stop has been touched within the last
3 minutes.

Add 1 Min

The Add 1 Min control (Start/Add 1 Min) starts the microwave
drawer at 100% power for 1 minute. Each additional touch of the
control will add 1 minute of cook time.
Cook time may be added in 1-minute increments to a cooking
cycle at the current power level by touching ADD 1 MIN during
the cycle. The Add 1 Min function cannot be used during Reheat,
Defrost, or any sensor cycles.
NOTE: To avoid unintentional operation of the microwave drawer,
the Add 1 Min control will work only if a cooking cycle has ended,
the drawer has been closed, or Stop has been touched within the
past 3 minutes.
6

MICROWAVE DRAWER CONTROLS

Clock

Start

Stop/Clear

The Stop control (Stop/Clear) clears any incorrect command,
pauses cooking, and cancels most functions with one touch of
the control. Touch STOP twice to cancel a running cooking cycle.
The microwave drawer will also turn off when the drawer is opened.
Close the drawer, and touch START to resume the non-sensor cycle.

Open/Close

To open the microwave drawer, gently pull on the drawer handle
so that the drawer opens automatically. To close the microwave
drawer, push the drawer with light pressure so that the drawer
closes automatically. In the event the drawer stops in the middle,
open or close the drawer manually to full open or close position by
gently pulling or pushing with even pressure near the middle of the
drawer handle.
If you wish to use key operation to open/close the microwave
drawer, touch the OPEN or CLOSE pad on the control panel to
open or close the drawer.
When opening or closing the drawer quickly, food in the microwave
drawer may be spilled. To clean, refer to the "General Cleaning"
section in "Microwave Drawer Care."
The Timer can be set in minutes and seconds, and counts down
the set time.
NOTE: The Timer does not start or stop the microwave drawer.
To Set Timer:
1. Touch TIMER/CLOCK, then number pad 1.
2. Enter time in minutes and seconds.
3. Touch TIMER/CLOCK again to start Timer.
Timer may be canceled at any time by touching STOP/CLEAR.

Control Lock

The Control Lock shuts down the control panel pads to avoid
unintended operation of the microwave drawer. When the control
is locked, only the Control Lock control will function.
To Lock/Unlock Control: Touch and hold CONTROL LOCK for
3 seconds. The display will indicate the lock status.
The Setup control (Setup/Help) provides access to the following
settings:
Tones: Sound off or on. See the "Tones" section.
■
Reminder tones: Reminder signal off or on. See the "Tones"
■
section
Auto start: See the "Auto Start" section
■
Demo Mode: Demo Mode on or off. See the "Demo Mode"
■
section

Timer

Setup