Table of Contents
Advertisement
Quick Links
MICROWAVE HOOD COMBINATION
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See "Installation
Requirements" section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in
these installation instructions.
MICROWAVE HOOD COMBINATION SAFETY
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
W10188238A
INSTALLATION INSTRUCTIONS
MICROWAVE HOOD COMBINATION SAFETY .............................. 1
INSTALLATION REQUIREMENTS ................................................... 2
Tools and Parts............................................................................... 2
Location Requirements................................................................... 2
Product Dimensions ....................................................................... 3
Electrical Requirements .................................................................. 3
INSTALLATION INSTRUCTIONS ..................................................... 4
Remove Mounting Plate ................................................................. 4
Rotate Blower Motor....................................................................... 4
Locate Wall Stud(s) ......................................................................... 6
Mark Rear Wall................................................................................ 6
Drill Holes in Rear Wall.................................................................... 7
Attach Mounting Plate to Wall ........................................................ 7
Prepare Upper Cabinet................................................................... 8
Install the Microwave Oven ............................................................ 8
Complete Installation ...................................................................... 9
VENTING DESIGN SPECIFICATIONS............................................ 10
ASSISTANCE ................................................................................... 11
Replacement Parts ....................................................................... 11
Accessories................................................................................... 11
Your safety and the safety of others are very important.
DANGER
Table of Contents
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
Advertisement
Table of Contents
Related Manuals for Jenn-Air JMV8208DB
Summary of Contents for Jenn-Air JMV8208DB
-
Page 1: Table Of Contents
MICROWAVE HOOD COMBINATION INSTALLATION INSTRUCTIONS This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See “Installation Requirements” section for further notes. These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in these installation instructions. -
Page 2: Installation Requirements
INSTALLATION REQUIREMENTS Tools and Parts Location Requirements Tools Needed Check the opening where the microwave oven will be installed. The location must provide: Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools ■... -
Page 3: Product Dimensions
Installation Dimensions Electrical Requirements NOTE: The grounded 3 prong outlet must be inside the upper cabinet. See “Electrical Requirements” section. WARNING 30" (76.2 cm) Electrical Shock Hazard min. Plug into a grounded 3 prong outlet. 30" (76.2 cm) typical* 12" (30.5 cm) min. Do not remove ground prong. -
Page 4: Installation Instructions
INSTALLATION INSTRUCTIONS 2. Remove the blower motor screw from the back of the microwave oven, then lift out blower motor. Remove Mounting Plate NOTE: To avoid possible damage to the work surface, cover the work surface. 1. Remove any remaining contents from the microwave oven cavity. - Page 5 6. Attach damper assembly to the rear exhaust vent opening by 4. Close damper plate and secure it with screw removed in sliding it down into the guides on both sides of the opening, Step 1 of “Wall Venting Installation Only.” and pushing it into the lower locking tabs.
-
Page 6: Locate Wall Stud(S)
Locate Wall Stud(s) Mark Rear Wall NOTE: If no wall studs exist within the cabinet opening, do not The microwave oven must be installed on a minimum of 1 wall install the microwave oven. stud, preferably 2, using a minimum of 1 lag screw, preferably 2. See illustrations in “Possible Wall Stud Configurations.”... -
Page 7: Drill Holes In Rear Wall
5. With the support tabs facing forward (see illustrations in “Locate Wall Stud(s)” section, align the mounting plate center Drill Holes in Rear Wall marker to the centerline on the wall, making sure its top edge In addition to being installed on at least 1 wall stud, the mounting is aligned with the horizontal line drawn in Step 3. -
Page 8: Prepare Upper Cabinet
Prepare Upper Cabinet Install the Microwave Oven 1. Disconnect power to outlet. WARNING 2. Remove all contents from upper cabinet. 3. Place Upper Cabinet Template against the bottom of the upper cabinet, and attach with tape or thumbtacks. Make sure Excessive Weight Hazard the template centerline aligns with the vertical centerline on Use two or more people to move and install... -
Page 9: Complete Installation
6. Push microwave oven against mounting plate and hold in For Roof Venting Installation Only place. NOTE: If microwave oven does not need to be adjusted, skip 11. Connect vent to damper assembly. steps 7-9. 7. If adjustment is required, rotate microwave oven downward. Using 2 or more people, lift microwave oven off of mounting plate, and set aside on a covered surface. -
Page 10: Venting Design Specifications
VENTING DESIGN SPECIFICATIONS This section is intended for architectural designer and Rectangular to Round Transition builder/contractor reference only. NOTE: The minimum 3" (7.6 cm) clearance must exist between the top of the microwave oven and the rectangular to round NOTES: transition piece so that the damper can open freely and fully. -
Page 11: Assistance
Recommended Vent Length A 3¹⁄₄ x 10 (8.3 x 25.4 cm) rectangular or 6 (15.2 cm) round vent 6" (15.2 cm) vent system = 73 ft (22.2 m) total " " " should be used. The total length of the vent system including straight vent, elbow(s), transitions and wall or roof caps must not exceed the equivalent of 140 ft (42.7 m) for either type of vent. - Page 12 W10188238A SP PN W10188947A DE68-03534A © 2008. 9/08 All rights reserved. Printed in Malaysia...
Need help?
Do you have a question about the JMV8208DB and is the answer not in the manual?
Questions and answers