Subscribe to Our Youtube Channel
Related Manuals for SCHUBERTH SRC System
Summary of Contents for SCHUBERTH SRC System
- Page 1 U S E R M A N U A L P O W E R E D B Y QG SRC 131 - QG0160.indd 21 10/20/09 11:26 AM...
-
Page 2: Table Of Contents
Table of ConTenTs 1. INTRODUCTION ............23 8. -
Page 3: Introduction
1. INTRODUCTION addITIONal SPECIal fEaTURES: Congratulations and thank you for choosing the Schuberth Rider Communication-System™ (SRC™-System™) Headset for motorcycle ➤Your headset is equipped with AGC technology (Automatic Gain helmets. Control), allowing your SRC-System to automatically increase or reduce its volume according to ambient noise and driving speed. -
Page 4: Contents Of The Retail Box
2. CONTENTS OF THE RETAIl BOx Wall charger plug USB adapter cable SRC-System for C3 helmets* Velcro® pads Flexible Boom Microphone MP3 cable Microphone sponges 2 Speakers User Manual, stickers Channel A Button IMPORTANT: Connector • Connect to Rider A Cover •... -
Page 5: Basic Setup And Configuration
disable/Enable status announcements: While on standby, press 4. BASIC SETUP AND CONFIGURATION and hold the Volume Down Button for 6 seconds. Led ON: indication: Solid blue + Audio feedback: One short beep 4.1 GeneRal fUnCTIons Led OFF: indication: Solid red + Audio feedback: Two short beeps dESIREd RESUlT REQUIREd aCTION 4.3 aUDIo soURCes anD PRIoRITIes... -
Page 6: Getting Started
remove the headset from the charger and turn it on again. Your head- 8. Make sure that both snap buttons remain fastened, and that the set should now respond as expected. microphone boom is located on the inner side of your helmet ( be- tween the SRC-System and the inner padding of the helmet). -
Page 7: Positioning The Microphone
2. Open the two red buttons located at the bottom part of the 3. Release the Acoustic Collar’s pins from their corresponding indenta- interior lining that cover the cheek pads. Lift the tions inside the helmets rim. lining slightly. 5.5 WeaRInG anD ReMoVInG THe HelMeT 3. -
Page 8: Connecting Bluetooth Enabled Mobile Phones, Gps Or Mp3 (A2Dp) Devices
6.1 MobIle PHone 6. CONNECTING BLUETOOTH ENABlED MOBIlE To use your Bluetooth mobile phone with the SRC-System, you must PHONES, GPS OR MP3 (A2DP) DEVICES first pair the two devices. Multiple device Connectivity (“MdC”) with Bluetooth NOTE: If you plan to use a GPS device in parallel with your mobile phone, then compatible devices you should pair your mobile phone to the GPS device and not to the SRC- Thanks to MDC technology the SRC-System offers parallel connectivity... -
Page 9: Gps Device
NOTE: If the pairing process is not completed within two minutes the NOTE: The priority schedule of your src-system has been set in a way to avoid headset will return to Standby mode. incoming intercom calls to interrupt GPS instructions in progress. In such case the intercom caller will hear a busy signal and you will hear two beeps, indicat- 6.2 GPs DeVICe ing that an intercom caller is trying to page you. -
Page 10: The Sound Of Music: Built-In Fm Radio And External Mp3 Player (Cable Option)
1. Turn on your MP3 Player or Adapter, and make sure that its 7. THE SOUND OF MUSIC: BUIlT-IN FM RADIO Bluetooth function is activated. AND ExTERNAl MP3 PlAyER (CABlE OPTION) 2. With the SRC-System headset turned ON, press and hold the Mobile Button for at least six seconds until the Red and Blue Lights 7.1 fM RaDIo begin alternating rapidly:... -
Page 11: Cable Connecting Your Mp3 Player Or Other External Audio Sources
3. Tap the CHANNEL “B” button within 20 seconds of finding the sta- RDS ON/OFF (press simultaneously 3 seconds while Radio is on) tion to save the current station. 4. To save another station, tap the CHANNEL “B” button again to reach next station number. -
Page 12: Using The Mobile Phone
STaTUS lIGHTS 8. USING THE MOBIlE PHONE lEd Indication Status INITIaTING aNd RECEIVING MObIlE PHONE CallS None Headset is off baSIC fUNCTIONS 1 blue flash every 3 seconds Standby – No call is in progress 2 blue flashes every 3 seconds Audio active answer a call Tap the Mobile Button or speak loudly any word of... -
Page 13: Before Starting The Intercom
9.3 befoRe sTaRTInG THe InTeRCoM NOTE: Selecting a CHANNEL that is already in use will override the paired Channel “B“ Button Channel “A“ Button headset on that CHANNEL with the newly paired headset. 4. On the SRC-System headset, press and hold the assigned CHAN- NEL BUTTON (“A”... -
Page 14: Receiving Intercom Calls
Initiate Intercom calls Use Channel “A” Use Channel “B” There are two ways to start an Intercom call with your paired headsets while the headset is in Standby mode: VOICE CONNECT: CHaNNEl bUTTON CONNECT: Start talking loudly Single tap the CHaNNEl “a” button Once you start talking loudly, an to add or remove the CHANNEL “A”... -
Page 15: Enable/Disable Voice Connect Feature
3. The Red and Blue Lights will flash five times simultaneously and then the headset will turn off, confirming that Reset was success- For additional information please visit our website at fully completed. www.schuberth.com For technical support please contact us at: 9.9 noTeWoRTHY IssUes support@src-system.com a. -
Page 16: Notices
Operation is subject to the following two conditions: IMPORTANT: OPENING AcOustIc cOllAr ZIPPEr VOIDs WArrANtY! 1) this device may not cause interference and 2) this device must accept any interference, including interference that may The electronic components inside the Acoustic Collar of the cause undesired operation of the device. -
Page 17: Waiver And General Release
IC Rf Radiation Exposure Statement: weather and road conditions if you choose to use the SRC System (the “Device”) , This equipment complies with IC radiation exposure limits set forth for an including all derivative models irrespective of its commercial name or branding, uncontrolled environment. - Page 18 COMPaNY aS dEfINEd abOVE. disclaimer of warranty THE COMPANY DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR www.schuberth.com QG SRC 131 - QG0160.indd 38 10/20/09 11:29 AM...
Need help?
Do you have a question about the SRC System and is the answer not in the manual?
Questions and answers
How do you change language from German to English on the SRC system
To change the language from German to English on the SCHUBERTH SRC System:
1. Make sure the headset is on standby.
2. Press and hold both the CHANNEL “A” and CHANNEL “B” buttons at the same time for 3 seconds.
3. The voice menu will start.
4. Follow the voice instructions to select English as your preferred language.
This answer is automatically generated