Merits P326A Owner's Manual
  1. Manuals
  2. Brands
  3. Merits Manuals
  4. Wheelchair
  5. P326A series
  6. Owner's manual

Merits P326A Owner's Manual

Hide thumbs Also See for P326A:
Table of Contents

Advertisement

Quick Links

See also: Service Manual
P326D

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the P326A and is the answer not in the manual?

Questions and answers

Greg Richardson
May 2, 2025

Where is the charging instructions

0

Subscribe to Our Youtube Channel

Related Manuals for Merits P326A

Summary of Contents for Merits P326A

  • Page 1 P326D...
  • Page 2 Adjusting the Footrest Position(P326D) DK-REMD 11 Controller Operation(P326D) LiNX Controller Operation...
  • Page 7 For P326D When lift the seat, please pay attention to the following: 1.Do not drive off-road or on any uneven surfaced roads. 2.Do not attempt to climb any curbs. 3.Do not attempt to cross any gap. 4.Do not attempt to climb any ramp. 5.Do not attempt to recline over 105°.
  • Page 10 driving outdoors...
  • Page 13 ramp ramp ramp...
  • Page 14 P326A...
  • Page 15 SEAT LIFT P326D...
  • Page 16 P326A P326D P326A P326D 17"~21"(43~53cm) 15.5"~19.5"(39~50cm) 21.5"~23.5"(55~60cm) 22"~29.5"(56~75cm) 60kg (132 lbs) 66kg (145 lbs) Dynamic Shark 40A PG VR2 40A Dynamic Shark 60A Dynamic LiNX 40A...
  • Page 17 Seat Lift：Power seat elevator available.
  • Page 18 For P326A For P326D (1)Disconnect the controller plug.(Fig A) (2)Lift seat up.(Fig C)
  • Page 19 For P326A For P326D Please to refer P25.
  • Page 20 Footrest Position Adjustment (P326D) (1) Put the Footrest in the tube.(Fig O) (2) Put in the plug. (Fig O) (3) Adjust the footrest to forward or backward, and then tighten the knob. (Fig O) Fig O...
  • Page 21 Fig P Fig Q Fig Q Fig P...
  • Page 26 8. The Fault Indicator - Flash Codes If a fault condition exists, the Fault Indicator LED shows a Flash Code. A flash code is a specific number of short flashes, followed by a pause. Flash Code If the fault is a serious fault that prevents the chair from driving, additionally the Battery Gauge shows a Drive Inhibit indication.
  • Page 27 9. Using the Seat Function Button (REMD11 & REMD21 Only) Two seat functions are available for individual adjustment and are accessed via the Seat Function Button. Press the Seat button once to toggle the control unit from Drive mode to Seat mode. Seat Function 1 will be active as noted by the amber coloured “1”...
  • Page 41 LiNX Controller The Remote There are two versions of the LiNX LE System Remote, namely the REM050, and REM060. Figure 36, and Figure 37, show the main features of these Remotes. These features are described in more detail in the following sec ons. Warning: Users should be aware that the surface of the Remote can poten ally get hot when it is exposed to strong sunlight for long periods.
  • Page 43 OONAPU OONAPU (“Out Of Neutral At Power Up”) is a safety feature that prevents accidental movement of the wheelchair, either when powering up, or when the wheelchair comes out of an inhibit state. If the LiNX LE System is turned on (or comes out of an inhibit state) while the joys ck is not in the t i s warning is displayed.
  • Page 56 Rev. 4. 01/11/2016...

This manual is also suitable for:

P326d

Table of Contents

Save PDF