Advertisement
Available languages
Available languages
Congratulations on purchasing your TIMEX
instructions carefully to understand how to operate your Timex timepiece.
HOW TO START YOUR WATCH
To start your watch remove the plastic guard from under the crown, then
press the crown in against the case. The second hand will begin advancing
in one-second intervals.
Some deep-depth water-resistant watches require the setting crown to be
screwed in to secure water-resistance. If your watch case has a protrusion
with screw threads, the crown must be screwed in after setting the watch.
To screw in, push the crown firmly against the threaded protrusion and hold
in while turning the crown clockwise. Continue to screw in the crown until it is
tight. You will need to unscrew the crown (counter-clockwise) before pulling
it out the next time you want to set your watch.
WATER AND SHOCK RESISTANCE
If your watch is water-resistant, meter marking or (O) is indicated.
Water-Resistance Depth
30m /98ft
50m /164ft
100m /328ft
200m /656ft
*pounds per square inch absolute
WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY
BUTTONS OR PULL OUT THE CROWN UNDER WATER UNLESS YOUR
WATCH IS INDICATED AS 200 METER WATER-RESISTANT.
1. Watch is water-resistant only as long as lens, push buttons and case
remain intact.
2. Watch is not a diver watch and should not be used for diving.
3. Rinse watch with fresh water after exposure to salt water.
4. Shock-resistance will be indicated on watch face or caseback. Watches
are designed to pass ISO test for shock-resistance. However, care should
be taken to avoid damaging crystal/lens.
DATE MODELS
TO SET TIME:
1) PULL crown all the way out and turn to correct time.
2) Push crown in to restart. For screw-in setting crown, push crown in while
turning CLOCKWISE to tighten.
Watches with date: Note correct time of day (A.M or P.M.) for proper date
function.
TO SET "QUICKDATE
" FEATURE:
®
3-POSITION CROWN:
1) Pull crown to "Middle" position and turn CLOCKWISE or
COUNTERCLOCKWISE until correct date appears.
2-POSITION CROWN:
1) Pull crown to "OUT" position and turn CLOCKWISE until date changes.
Repeat until correct date appears. Adjust date when month has less than
31 days. Push crown in when finished.
Caution: Wearing or storing the watch with the crown in the "middle" position
will cause damage to the movement. Always return the crown to the normal
position, or if you wish to save the battery life while storing the watch, leave
the crown in the "out" position.
The date function advances the date between the hours of 10 PM and 2 AM.
Avoid setting the date during this timeframe. If you attempt to set the date
during this time period, rotate the crown at a very slow rate to avoid damag-
ing the watch.
watch. Please read these
®
p.s.i.a. * Water Pressure Below Surface
60
86
160
284
DATE
A
B
C
CROWN POSITION
Register your product at www.timex.com
DAY / DATE MODELS
TO SET THE TIME:
1) PULL the crown out to the "C" position.
2) TURN the crown either way to the correct time.
3) PUSH in the crown to the "A" position.
TO SET THE DATE:
1) PULL the crown out to the "B" position.
2) TURN the crown either way to the correct date.
3) PUSH in the crown to the "A" position.
HOW TO ADJUST BRACELET
FOLDOVER CLASP BRACELET
1. Find spring bar that connects bracelet to clasp.
2. Using a pointed tool, push in spring bar and gently twist bracelet to
disengage.
3. Determine wrist size, then insert spring bar in correct bottom hole.
4. Push down on spring bar, align with top hole and release to lock in place.
FIG. 1
BRACELET LINK REMOVAL
REMOVING LINKS:
1. Place bracelet upright and insert pointed tool in opening of link.
2. Push pin forcefully in direction of arrow until link is detached (pins are
designed to be difficult to remove).
3. Repeat until desired number of links are removed.
RE-ASSEMBLY:
1. Rejoin bracelet parts.
2. Push pin back into link in opposite direction of arrow.
3. Press pin down securely into bracelet until it is flush.
1
ENGLSH 991-096324
REVISED 10.25.17
DATE
A
B
C
CROWN POSITION
FIG. 2
FIG. 3
Advertisement
