LCN 3130 Series Installation Instructions

*25051*
25051
Not for installation on UL rated 20 minute wood core doors per CAN/ULC-S104-10
IMPROPER INSTALLATION OR REGULATION MAY
RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE.
FOLLOW ALL INSTRUCTIONS CAREFULLY. FOR
QUESTIONS, CALL LCN AT 877-671-7011.
1
Installation
LH
MAXIMUM
11.5 ft/lbs
=
OPENING
15 N-m
TORQUE
LH
MAXIMUM
11.5 ft/lbs
OPENING =
TORQUE
1a Determine hand of door using diagram above. Hand of
closer must match hand of door. The closer mtg. plate
is marked with an "R" or "L". Prepare door & frame per
LH RH
template on reverse side. Template page shows a LH
MAXIMUM
MAXIMUM
11.5 ft/lbs
11.5 ft/lbs installation, RH is opposite. Proper mortising of door
OPENING =
OPENING =
15 N-m
TORQUE
TORQUE 15 N-m
and frame is required for closer to operate correctly.
1b Install closer into door as shown below and secure
with screws provided (as called out on template).
1c Attach arm to closer as shown below, then fasten with
arm shaft screw. Arm must be pre-loaded approx. 20°,
as shown. When installed correctly, arm should press
against the lip at top of door.
1d Insert track
roller into end of
track, as shown
below. Place
track up into
mortise with
hold open holes
in top of track
toward hinge.
Secure with
screws
provided.
Customer Service
1-877-671-7011
3130 Series
CAUTION
LH RH
LH RH
LH MAXIMUM RH
MAXIMUM
MAXIMUM 11.5 ft/lbs
MAXIMUM
11.5 ft/lbs
OPENING =
11.5 ft/lbs
OPENING = OPENING
OPENING =
15 N-m
TORQUE
15 N-m
TORQUE TORQUE
15 N-m
TORQUE
MAXIMUM
MAXIMUM
11.5 ft/lbs
11.5 ft/lbs
OPENING =
OPENING =
15 N-m
TORQUE
TORQUE 15 N-m
RH
MAXIMUM
11.5 ft/lbs
OPENING =
TORQUE 15 N-m
RH
MAXIMUM
11.5 ft/lbs
OPENING =
15 N-m
TORQUE
15 N-m
www.allegion.com/us
1e Open door partially and pull arm away from door. Fit
arm onto track roller stud. NOTE: It may be necessary
to loosen
arm set
11.5 ft/lbs
=
15 N-m
screw
before arm
will fit onto
roller stud.
Once arm
is fitted
firmly onto
roller stud,
use the
socket
screw key provided and tighten arm set screw. Open
door to approx. 90° and allow the door to close,
observing closing speed. If adjustments are needed,
refer to step F.
2
Closer Regulation
The 3130 series closer has been regulated prior to shipment.
If adjustments are needed, use a C\cx" hex wrench and consult
diagram below.
LATCH
SPEED
LATCH
SPEED
3
Hold-Open Information
MAIN LIGHT HOLD-OPEN FORCE
LATCH
BACKCHECK
SPEED SPEED
LONG
GREEN
SCREW
b
x2
HINGE
GREEN
or
SIDE
SCREW
HINGE
LONG CAM
SHORT SIDE
GREEN
SCREW
SCREW
HINGE
SIDE
LATCH MAIN
LATCH MAIN BACKCHECK
BACKCHECK
SPEED SPEED
SPEED SPEED
MAIN
LATCH
BACKCHECK
SPEED SPEED
MAIN
BACKCHECK
SPEED
MAIN
BACKCHECK
SPEED
BACKCHECK
LONG CAM
LONG CAM
SHORT
GREEN
GREEN
SCREW
LONG CAM
SCREW
SCREW
SHORT
GREEN
SCREW
SCREW
HOLD-OPEN OPTION
MAIN SPEED
STRONG HOLD-OPEN FORCE
HINGE
HINGE
LATCH
SIDE
SIDE b
SPEED
HINGE
CAM
x2
SHORT
SIDE
SCREW
a
a
LONG CAM
SHORT SPRING
SCREW CLIP
TRACK
SPRING
CLIP
Installation Instructions
BACKCHECK
BACKCHECK
BACKCHECK
MAIN SPEED
MAIN SPEED
MAIN SPEED
LATCH
SPEED
BACKCHECK
LATCH
SPEED
MAIN SPEED
BACKCHECK
LATCH
SPEED
MAIN SPEED
LATCH
SHORT SPEED
TRACK
TRACK
SCREW
TRACK
SPRING
SPRING
CLIP
CLIP
SPRING
CLIP
TRACK
TRACK
SPRING
CLIP
© Allegion 2015
Printed in U.S.A.
25051 Rev. 10/15-h
LATCH
SPEED