Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Optical Systems Design OSD2153P
Summary of Contents for Optical Systems Design OSD2153P
-
Page 1: Index
OPERATOR MANUAL OSD2153P SERIES GIGABIT ETHERNET MEDIA CONVERTER WITH PoE... - Page 2 OPTICAL SYSTEMS DESIGN DOC ID: 10115804 PAGE 2 OSD2153P OPERATOR MANUAL...
-
Page 3: Table Of Contents
APPLICATIONS ........................5 1.1.3 FEATURES AND BENEFITS ..................... 5 TYPICAL CONFIGURATION ....................6 TECHNICAL SPECIFICATIONS ................... 7 OSD2153P FRONT AND REAR PANELS ................8 INSTALLATION AND OPERATION ..................9 INTRODUCTION ........................9 INSTALLATION ........................9 2.2.1 WARNING AND PRECAUTIONS ..................9 2.2.2... - Page 4 TABLE 1: TECHNICAL SPECIFICATIONS ..................7 TABLE 2: POWER CONNECTION ..................... 11 TABLE 3: LED FUNCTION ......................... 12 TABLE 4: OSD2153P 3-WAY DIP SWITCH SETTINGS ..............13 TABLE 5: CONFIGURATION WITH LLF ENABLED ..............16 TABLE 6: CONFIGURATION WITH LLF DISABLED ..............16...
-
Page 5: Technical Summary
50km of singlemode fiber is possible by use of the appropriate optical device. A major benefit of the OSD2153P is its reliable operation over the -20°C to +75°C temperature range which allows it to be used in environments such as roadside cabinets, mine sites and factories. -
Page 6: Typical Configuration
OPTICAL SYSTEMS DESIGN TYPICAL CONFIGURATION Figure 1 below indicates the typical set-up for an OSD2153P system. FIGURE 1: OSD2153P TYPICAL CONFIGURATIONS DOC ID: 10115804 PAGE 6 OSD2153P OPERATOR MANUAL... -
Page 7: Technical Specifications
(attached power device dependant) Power Requirements >52VDC recommended for PoE+ or ≥55VDC for 60W PoE 2 Way 3.5mm Terminal Block on the module Power Connector Dimensions (mm) 90W x 58D x 49H 0.3kg Weight 1022153P03 DOC ID: 10115804 PAGE 7 OSD2153P OPERATOR MANUAL... -
Page 8: Osd2153P Front And Rear Panels
OPTICAL SYSTEMS DESIGN OSD2153P FRONT AND REAR PANELS There is one fixed copper port for 10/100/1000Base-T, one SFP port and a 2-way terminal block power connector on the front panel. The SFP device is sold separately giving the user choice to use either one or two fiber communications with various optical power outputs depending on the distance required. -
Page 9: Installation And Operation
2 INSTALLATION AND OPERATION INTRODUCTION This section outlines the methods required to install and operate the OSD2153P successfully. It should be studied carefully if damage to the equipment or poor results are to be avoided. This equipment has been fully tested prior to dispatch and is ready for immediate operation. However it is advisable to check for external transportation damage before operation. -
Page 10: Osd2153P Drawings And Dimensions
OSD2153P DRAWINGS AND DIMENSIONS The standard OSD2153P is designed to be mounted on an even surface and to be secured by means of M4 or smaller screws. All dimensions are in mm. The unit also can be mounted on a standard DIN rail with the OSD2153P DIN Rail bracket. -
Page 11: Power Supply Connections
The OSD2153P complies with IEEE802.3af, IEEE802.3at and PoE++, and is capable of supplying up to 60W of PoE. The OSD2153P supports Mode A (i.e. transmitting power over pins 1, 2, 3, & 6) and Mode B (i.e. transmitting power over pins 4, 5, 7, & 8). For PoE++ the OSD2153P transmits power over all 8 pins. -
Page 12: Led Indicators
Link Loss Forwarding Enabled Green Link Loss Forwarding Disabled Fiber Speed: LNK SPD 100Mbps: 3 Times/Sec Green No Optical Link Activity 1Gbps: 6 Times/Sec Note: (1) Activity indicates traffic for both copper and fiber port. DOC ID: 10115804 PAGE 12 OSD2153P OPERATOR MANUAL... -
Page 13: Controls
OPTICAL SYSTEMS DESIGN 2.2.6 CONTROLS The OSD2153P has a 3-way DIP switch to control a number of functions. Figure 8 outlines the function of each switch. For correct operation, set the required switch settings before powering the unit. Fiber Speed... -
Page 14: Fitting Sfp Connectors
Using the lever, gently pull the SFP out. Fiber SFP Inserting Removing FIGURE 9: FITTING/REMOVING SFP CONNECTORS 2.2.8 BASIC CONNECTIONS Figure 10 shows basic user connections to the OSD2153P. Chassis Ground LC Fiber cable Ethernet cable Power FIGURE 10: BASIC CONNECTIONS DOC ID: 10115804... -
Page 15: Osd2153P Operation
There are two possible configurations for the OSD2153P namely Single Unit Configuration and Dual Unit configuration. Figure 11 is a flow chart of the OSD2153P Link Loss Forwarding (LLF) function and operation. FIGURE 11: LINK LOSS FORWARDING FUNCTION 2.3.1... -
Page 16: Table 5: Configuration With Llf Enabled
OPTICAL SYSTEMS DESIGN The following tables outline the recommended switch settings for the OSD2153P. Any changes in switch settings require power up to take effect. TABLE 5: CONFIGURATION WITH LLF ENABLED Configurations Case1 Case2 Case3 Case4 Switch Setting 1. LLF detects fiber &... -
Page 17: Figure 13: Copper Connection Loss
OPTICAL SYSTEMS DESIGN Examples Figure 13 is an example of a copper connection loss. The OSD2153P will detect that there is no copper connection received and then disable the transmission to the fiber port. The 1000Base-X switch will thus be notified that there has been a copper link loss. -
Page 18: Maintenance
OPTICAL SYSTEMS DESIGN 3 MAINTENANCE INTRODUCTION The following section outlines the fault-finding procedure for the OSD2153P modems. Please take note of the following: Personnel without appropriate training should not attempt any maintenance except that outlined ▲ below. If further maintenance is attempted you are warned that every care should be taken to ensure that ▲... -
Page 19: Warranty
For warranty period, please call your local OSD distributor. REPAIRS Optical Systems Design reserves the right to repair or replace faulty modules/units. Please obtain a “Return Material Authorisation” (RMA) form and number before returning goods. Goods must be returned in adequate packing material to Optical Systems Design, Warriewood or its nominated authorised representative, for all repairs. - Page 20 OPTIC L Optical Systems Design Pty. Ltd. 7/1 Vuko Pl. Warriewood 2102 SYSTEMS P.O. Box 891 Mona Vale N.S.W. Australia 2103 Telephone: +61 2 9913 8540 DESIGN Facsimile: +61 2 9913 8735 Email: sales@osd.com.au Web Site: www.osd.com.au PTY LTD A.B.N. 83 003 020 504...