Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Optical Systems Design OSD2168M Series
Summary of Contents for Optical Systems Design OSD2168M Series
-
Page 1: Index
OPERATOR MANUAL OSD2168M SERIES GIGABIT PoE+ ETHERNET MEDIA CONVERTER... -
Page 3: Table Of Contents
OPTICAL SYSTEMS DESIGN INDEX 1 TECHNICAL SUMMARY ......................4 BRIEF DESCRIPTION ......................4 1.1.1 OVERVIEW ......................... 4 1.1.2 APPLICATIONS ........................4 1.1.3 FEATURES AND BENEFITS ..................... 4 TYPICAL CONFIGURATION ....................5 TECHNICAL SPECIFICATIONS ................... 6 OSD2168M FRONT AND REAR PANELS ................7 INSTALLATION AND OPERATION .................. -
Page 4: Technical Summary
OPTICAL SYSTEMS DESIGN 1 TECHNICAL SUMMARY BRIEF DESCRIPTION 1.1.1 OVERVIEW The OSD2168M is designed to convert between 10/100/1000Base-T copper cabling and 1000Base-Sx fiber cabling. It has one PoE+ RJ45 copper port which provides up to 25.4W and one optical port for operation over two fibers. -
Page 5: Typical Configuration
OPTICAL SYSTEMS DESIGN TYPICAL CONFIGURATION Figure 1 below indicates a typical set-up for an OSD2168M system. FIGURE 1: OSD2168M TYPICAL CONFIGURATION DOC ID: 10114302 PAGE 5 OSD2168M OPERATOR MANUAL... -
Page 6: Technical Specifications
OPTICAL SYSTEMS DESIGN TECHNICAL SPECIFICATIONS TABLE 1: TECHNICAL SPECIFICATIONS SPECIFICATION PERFORMANCE IEEE802.3i/802.3u/802.3ab 10/100/1000Base-T Ethernet Electrical Data Interface Electrical Data Rate 10, 100, 1000Mbps with energy detect, auto negotiate, auto MDIX IEEE802.3z 1000Base-Sx Optical Data Interface Optical Data Rate 1000Mbps Half or full duplex for 10/100... -
Page 7: Osd2168M Front And Rear Panels
OPTICAL SYSTEMS DESIGN OSD2168M FRONT AND REAR PANELS There is one fixed copper port for 10/100/1000Base-T and one SC 1000Base-Sx optical port on the front panel. The rear panel consists of a 2-way terminal block power connector. Each section will be described further throughout this manual. -
Page 8: Installation And Operation
OPTICAL SYSTEMS DESIGN 2 INSTALLATION AND OPERATION INTRODUCTION This section outlines the methods required to install and operate the OSD2168M successfully. It should be studied carefully if damage to the equipment or poor results are to be avoided. This equipment has been fully tested prior to dispatch and is ready for immediate operation. However it is advisable to check for external transportation damage before operation. -
Page 9: Osd2168M Drawings And Dimensions
OPTICAL SYSTEMS DESIGN 2.2.2 OSD2168M DRAWINGS AND DIMENSIONS The OSD2168M is designed to be mounted on an even surface and to be secured by means of M4 or smaller screws. 25.6 25.6 DETAIL A Ø8.5 R2.1 R2.1 DETAIL A 83.4 FIGURE 3: OSD2168M MOUNTING DIMENSIONS 2.2.3... -
Page 10: Fixed Rj45 Copper Port Pin Assignments
OPTICAL SYSTEMS DESIGN 2.2.4 FIXED RJ45 COPPER PORT PIN ASSIGNMENTS Figure 5 shows the pin configuration for the fixed RJ45 copper port. Green LED: Amber LED: 1: Tx+ Speed/Status Link/Act 2: Tx- 3: Rx+ 4: PoE (+) 5: PoE (+) -
Page 11: Basic Connections
OPTICAL SYSTEMS DESIGN 2.2.6 BASIC CONNECTIONS Figure 7 shows basic user connections to the OSD2168M Duplex SC Power Fiber cable OSD2168M RJ45 Ethernet Cable FIGURE 7: BASIC CONNECTIONS DOC ID: 10114302 PAGE 11 OSD2168M OPERATOR MANUAL... -
Page 12: Maintenance
OPTICAL SYSTEMS DESIGN 3 MAINTENANCE INTRODUCTION The following section outlines the fault-finding procedure for the OSD2168M modems. Please take note of the following: Personnel without appropriate training should not attempt any maintenance except that outlined ▲ below. If further maintenance is attempted you are warned that every care should be taken to ensure that ▲... -
Page 13: Warranty
For warranty period, please call your local OSD distributor. REPAIRS Optical Systems Design reserves the right to repair or replace faulty modules/units. Please obtain a “Return Material Authorisation” (RMA) form and number before returning goods. Goods must be returned in adequate packing material to Optical Systems Design, Warriewood or its nominated authorised representative, for all repairs. - Page 14 OPTICAL SYSTEMS DESIGN DOC ID: 10114302 PAGE 14 OSD2168M OPERATOR MANUAL...
- Page 16 OPTIC L Optical Systems Design Pty. Ltd. 7/1 Vuko Pl. Warriewood 2102 SYSTEMS P.O. Box 891 Mona Vale N.S.W. Australia 2103 Telephone: +61 2 9913 8540 DESIGN Facsimile: +61 2 9913 8735 Email: sales@osd.com.au Web Site: www.osd.com.au PTY LTD A.B.N. 83 003 020 504...