This document as well as all reports, drawings, data, information, or other material, whether accompanying it are the property of WIDE Corporation, are disclosed by WIDE only in confidence, and, except as WIDE may otherwise permit in writing, are to be used, disclosed, or copied only to the extent necessary for the evaluation thereof by recipient, or higher-tier contractor or subcontractor.
Page No. Title IDP2800SQ 6 / 77 (SL28P2K) SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Page 7
Page No. Title IDP2800SQ 7 / 77 (SL28P2K) ON CLEANING The screen is made of thin glass with a plastic surface and can be damaged if dropped, hit and scratched. Do not clean the front panel with keton-type materials(e.g., acetone), ethyl alcohol, toluene, ethyl acid, methyl or chloride –...
Page No. Title IDP2800SQ 8 / 77 (SL28P2K) FCC INFORMATION USER INSTRUCTIONS The Federal Communications Commission Radio Frequency Interference Statement includes the following warning: NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
The IDP2800SQ provides 16.7 million true colors (8 bit) per pixel. Each pixel is divided into Red, Green and Blue sub pixels which are arranged in vertical stripes and each sub-pixel is controlled in 256 grey levels.
1.1.3 Input Signal Specifications IDP2800SQ provides maximum three (3) input signal interfaces, an analog input and 2 x digital input. One input is displayed at a time by automatic* and/or manual input selection. (* Factory setting is automatic)
Page No. Title IDP2800SQ 13 / 77 (SL28P2K) Standard input resolution is 2K x 2K (2048 x 2048 pixels) Other resolutions are supported as specified below. Three scaling method are provided for input signals with resolutions less than the standard input resolution 2048 x 2048 pixels.
Remote Control via serial ports (CRT type, Sony DDM compatible) There are serial ports on the back side of the IDP2800SQ for remote control of the monitor by customer application. Either Sony DDM protocol (RS-422) or WIDE serial communication protocol (RS-232) can be used.
Page No. Title IDP2800SQ 16 / 77 (SL28P2K) 1.1.8 Connection Power Input ● 100-250Vac, 50/60Hz with double pole / neutral fusing, 250V F3.15AL ● Disconnect power before changing fuse ● Secondary power adapter : 12Vdc, 15A, 180W with UL60950, cUL, CE , FCC approved.
Page 17
3. TX_DL 4. No connection 5. No connection 6. No connection 7. Ground 8. No connection 9. No connection Control ● Connection Type : 8p miniDIN ● for communication with control module provided from WIDE Issued Date Revision Status 2009-06-08 V5.3...
Weight (kg / lbs) 26.0 / 57.3 35.0 / 77.21 The following figures show a chassis version mechanical dimension. IDP2800SQ basically provides three input connectors and all connectors are located the bottom side of monitor. < IDP2800SQ Front View : unit mm >...
Page 19
Page No. Title IDP2800SQ 19 / 77 (SL28P2K) < IDP2800SQ Bottom View > < IDP2800SQ Rear View > Issued Date Revision Status 2009-06-08 V5.3...
Page 20
Page No. Title IDP2800SQ 20 / 77 (SL28P2K) < IDP2800SQ Top View > < IDP2800SQ Side View : unit mm> Issued Date Revision Status 2009-06-08 V5.3...
Depth (mm / inch) 380 / 14.96 846 / 33.30 Weight (kg / lbs) 39.0 / 86 49.0 / 108.1 The following figures show a desktop version mechanical dimension. < IDP2800SQ Front View : unit mm > Issued Date Revision Status 2009-06-08 V5.3...
Page 22
Page No. Title IDP2800SQ 22 / 77 (SL28P2K) < IDP2800SQ Bottom View > < IDP2800SQ Rear View > Issued Date Revision Status 2009-06-08 V5.3...
Page 23
Page No. Title IDP2800SQ 23 / 77 (SL28P2K) < IDP2800SQ Top View > < IDP2800SQ Side View : unit mm> Issued Date Revision Status 2009-06-08 V5.3...
215.9 / 8.49 846 / 33.30 Weight (kg / lbs) 30.5 / 67.2 40.5 / 89.29 The following figures show a VESA Mounting version mechanical dimension. < IDP2800SQ Front View : unit mm > Issued Date Revision Status 2009-06-08 V5.3...
Page 25
Page No. Title IDP2800SQ 25 / 77 (SL28P2K) < IDP2800SQ Bottom View > < IDP2800SQ Rear View > Issued Date Revision Status 2009-06-08 V5.3...
Page 26
Page No. Title IDP2800SQ 26 / 77 (SL28P2K) < IDP2800SQ Top View > < IDP2800SQ Side View : unit mm> Issued Date Revision Status 2009-06-08 V5.3...
Page No. Title IDP2800SQ 27 / 77 (SL28P2K) 1.2.4 Assembly / Disassembly How to disjoint the stand ASS’Y and cover (see the below figure) 1. Switch off and disconnect the power code before performing the disjointing 2. Unscrew the three bolts and remove it 3.
Page 28
Page No. Title IDP2800SQ 28 / 77 (SL28P2K) How to disjointing stand VESA mount (see the below figure) 1. Switch off and disconnect the power code before performing the disjointing 2. Unscrew the three bolts and remove it 3. Pull out the VESA mount 4.
29 / 77 (SL28P2K) 1.2.5 Modular Design IDP2800SQ is a Line Replaceable Unit (LRU). Functionally related elements are packaged in basic building blocks as follows: LCD Panel Module: integrating the Protective Filter Glass, AMLCD, CCFL backlights and so on.
1.4.2 Maintainability 1.4.2.1 MTTR (Mean Time Between Repair) IDP2800SQ is defined as a Line Replaceable Unit (LRU) and the unit is designed to allow for an MTTR less than 0.5 hour (30 minutes). 1.4.2.2 Use of maintenance equipment ...
Page 31
Page No. Title IDP2800SQ 31 / 77 (SL28P2K) How to replace the backlights (see the below figure) 1. Switch off and disconnect the power code before performing the backlight replacement 2. Pull out the Cover-lamp 3. Disconnect the three backlight harnesses 4.
Page No. Title IDP2800SQ 32 / 77 (SL28P2K) 1.4.3 Operational Redundancy 1.4.3.1 Backlights Redundancy Three backlight trays are controlled independently for operational redundancy. When any one out of three backlights goes out of service, the remaining backlight trays still operational to provide good readability on screen.
Get/Set OSD data Available checking monitor status. WIDE agent snmp version is SNMPv1. What’s provided. Available to manage the Agent monitor using network(SNMP). Our monitor sends the error event or alert message to manger system by Trap ...
Page No. Title IDP2800SQ 34 / 77 (SL28P2K) IP Setting IP address and trap ip etc are needed for using SNMP. So must set ip address. It is provided to set the IP address on the OSD menu. 2.3.1 IP Address “IP Adress”...
Page No. Title IDP2800SQ 35 / 77 (SL28P2K) 2.3.2 Submask “Submask” is the submenu of “TCP/IP”, which set the submask of the monitor. User is able to set submask with rotating the encoder switch clockwise or counter-clockwise. For setting next digit push the encoder switch.
Page No. Title IDP2800SQ 36 / 77 (SL28P2K) 2.3.4 Trap IP Address “Trap IP Adress” is the submenu of “TCP/IP”, which set the trap IP address of the monitor. When there are some problems on the monitor, it sends the notification message to the host which has this trap IP address by SNMP protocol.
Status 2 indicator Status 1 indicator Source Selection Button Soft-Power Encoder Switch Button Below describes the internal type’s module (Desk top type) of IDP2800SQ with the push buttons and LED indicators Encoder Switch Source Selection Status 1 indicator button Status 2 indicator...
3.2.2 Source Selection IDP2800SQ supports to input three sources, one analog and two DVI inputs. One of three is able to be chosen by mean of either pushing source key on the control module or OSD navigation. To push the source key can select the source wanted to display directly without OSD navigation.
Page No. Title IDP2800SQ 39 / 77 (SL28P2K) converter analog to digital means “sampling”. And, the sampling frequency means the number of sampling to converter analog to digital, the valid data on analog signal is the certain number of data. It is dependant on the signal timing from PC.
Page No. Title IDP2800SQ 40 / 77 (SL28P2K) similar. Its adjustment range is -127 to +127. The closer to -127 it is, the darker it is and the closer to +127 it is, the brighter it is. When one of the submenu of “Adjustment” is selected, the encoder switch turned and push to select it.
Page No. Title IDP2800SQ 41 / 77 (SL28P2K) adjustment range is 0 to +100. When one of the submenus of “Adjustment” selected, turn the encoder switch and push to select it. And then Turn the encoder switch, so that adjust the values of the Contrast. When the encoder switch pushed again, going to the upper menu.
Page No. Title IDP2800SQ 42 / 77 (SL28P2K) When one of the submenus of “Adjustment” selected, turn to the encoder switch and push to select it. And then Turn to the encoder switch, so that adjust the values of the Dim Brightness. When the encoder switch pushed again, going to the upper menu Adjusting “Dim brightness”...
Page No. Title IDP2800SQ 44 / 77 (SL28P2K) When you select the input source, the display unit will switch signal source. Before displaying an input, the message of an input source is displayed for a while after the main menu disappeared and the input message will disappear after 5 seconds also.
Page No. Title IDP2800SQ 45 / 77 (SL28P2K) 3.3.3.2 DVI 1 “DVI 1” is the submenu of “Input Source”, which sets up the digital signal getting from DVI 1port. When one of the submenus of “Input source” selected, turn the encoder switch and push to select it, so that the screen is represented as below the right side figure.
Page No. Title IDP2800SQ 46 / 77 (SL28P2K) The “Advanced Setting” menu is to tune the analog signal and set up the source priority and basic menu lock. It is protected by the password. When a 4-digit password asked, enter it using the encoder switch to turn to a digit and push to select it.
Page No. Title IDP2800SQ 47 / 77 (SL28P2K) Advanced Settings Advanced Settings Analog adjustment Phase Phase Frequency H-Position V-Position Return : Select : Move : Select : Move <select phase menu> <adjust a phase> “Phase” is the submenu of “Analog adjustment”, which controls the phase of a sampling clock within one pixel period, The frequency should be set correct first (see below) and Auto-Auto is disabled (see the 3.3.4.2.3).
Page No. Title IDP2800SQ 48 / 77 (SL28P2K) Advanced Settings Advanced Settings Analog adjustment Phase Frequency Frequency H-Position V-Position Return : Select : Move : Select : Move <select frequency menu> <adjust a frequency> The “frequency” is the menu for the setting of the number of pixels corresponding to the pixel rate of the applied analog input signal.
Page No. Title IDP2800SQ 49 / 77 (SL28P2K) 3.3.4.1.4 V-Position “V-Position” is the submenu of “Analog adjustment”, which controls the vertical position of image, Its adjustment range is 0 to +100 and default is 50. When the V-position of the submenu of “Analog adjustment”...
Page No. Title IDP2800SQ 50 / 77 (SL28P2K) “Source Priority” is the submenu of “Set-Up”, which sets up the priority about the input sources: analog1, DVI1, and DVI2. This priority makes a decision the input signal to display on the screen when the monitor turns on.
Page No. Title IDP2800SQ 51 / 77 (SL28P2K) Advanced Settings Advanced Settings Set-Up Auto-Auto Source Priority Auto Phase Auto-Tune Auto-Auto Basic Menu Lock User Password Return : Select : Move : Select : Move 3.3.4.2.4 Basic Menu Lock This menu item is for locking the switch and button function on control module. But, the soft-power button is not locked although it is “Menu Lock”.
Page No. Title IDP2800SQ 52 / 77 (SL28P2K) 3.3.4.4 Information “Information” is the submenu of “Advanced setting”, which represents input signal information, the resolution and the frequencies of synchronization signals. This is the information on user level, if more, you should access on administrator level.
Page No. Title IDP2800SQ 53 / 77 (SL28P2K) section, the administrator is able to control the “advanced settings” menu. Admin. Settings Admin. Settings Advanced Settings Advanced Settings Display Info. Back-light Menu Analog adjustment Fan Control Menu Set up Temperature Menu...
Page No. Title IDP2800SQ 54 / 77 (SL28P2K) the power and contact us first. See 3.3.5.5. 3.3.5.2.4. BL Status “BL Status” describes the current age status of BL’s. “Fault” means that the BL age is over than the fault age set at menu and “Warning”...
Page No. Title IDP2800SQ 55 / 77 (SL28P2K) “SBC” is the submenu of “SBC”, which turn on or off the SBC function. 3.3.5.3.1.2 SBC value “SBC value” controls the light of backlights, Its adjustment range is 50 cd/m to 200 cd/m .
Page No. Title IDP2800SQ 56 / 77 (SL28P2K) 3.3.5.4 Fan control Menu “Fan control menu” is for setting and reading fans options. See a below. Admin. Settings Fan Control Control Life time Return : Select : Move 3.3.5.4.1. Control “Fan control” menu controls the time when fans operates. Possible selection are AUTO, 5, 10, 15, and 20(default).
Page No. Title IDP2800SQ 57 / 77 (SL28P2K) Admin. Settings Life Time Warning at 4000 Fault at 5000 Current Age of Fan's Left : Right : Return : Select : Move 3.3.5.5 Temperature Menu “Temperature Menu” is the menu for showing two critical internal temperatures and for setting corresponding temperature Warning and Fault levels.
Page No. Title IDP2800SQ 58 / 77 (SL28P2K) Admin. Settings Test Pattern Pattern Pattern Pattern Pattern Pattern Pattern : Select : Move 3.3.5.7 Set-Up “Set-Up” is the submenu of “Admin. Settings”, which controls the factory reset, communication, Auto Color, RGB Black Level, RGB Gain and OSD set up.
Page No. Title IDP2800SQ 59 / 77 (SL28P2K) the current settings are stored in a user settings storage area on main control board. At administrator level, the current settings are replaced by the factory settings. The user settings disappear after changing by the factory settings.
Page No. Title IDP2800SQ 60 / 77 (SL28P2K) 3.3.5.7.3 RGB Adjust “RGB Adjust” is the submenu of “Set-Up” which sets up the gamma, auto color, RGB Black level, and RGB Gain. 3.3.5.7.3.1 Gamma “Gamma” is for correcting the input data more perceptually. Intensity response of monitor(LCD) to input voltage(Data) is not linear.
Page No. Title IDP2800SQ 61 / 77 (SL28P2K) Admin. Settings Auto Color : Select : Move (This OSD is displayed when it is enabled) 3.3.5.7.3.3 RGB Black Level(Available only in analog mode) “RGB Black Level” is the submenu of “RGB Adjust” for adjusting R, G and B black level individually.
Page No. Title IDP2800SQ 62 / 77 (SL28P2K) When all black levels are on the points of OSD 50, the amount of color is the same each other. But, if the level is moved closed to OSD 100, the amount of color to adjust is more, so, the color to adjust looks like strong.
Page No. Title IDP2800SQ 63 / 77 (SL28P2K) When all white levels are on the points of OSD 50, the amount of color is the same each other. But, if the level is moved closed to OSD 100, the amount of color to adjust is more, so, the color to adjust looks like strong.
Page No. Title IDP2800SQ 64 / 77 (SL28P2K) 3.3.5.7.4.3 LED Display “LED Display” is the submenu of “OSD Set Up”, which display the LED of the input source on the screen where you chosen. 3.3.5.7.4.3.1 LED ON/OFF “LED ON/OFF” is the submenu of “LED Display”.
Page No. Title IDP2800SQ 65 / 77 (SL28P2K) Admin. Settings Admin. Settings Password : Select : Move 3.3.5.7.6 Quick Searching Mode If “Quick Search Mode” is On, the detection time of source is minimized. 3.3.5.7.7 TCP/IP “TCP/IP” menu is for SNMP(Simple Network Mangement Protocol).
Page No. Title IDP2800SQ 66 / 77 (SL28P2K) 3.3.5.7.7.3 Gateway “Gateway” is the submenu of “TCP/IP”, which set the gateway of the monitor. 3.3.5.7.7.4 Trap IP Address “Trap IP Adress” is the submenu of “TCP/IP”, which set the trap IP address of the monitor.
We recommend that do not repair this product or replace the internal modules by yourself, contact the sales people or customer supporting team in WIDE. Our service strategy is to swap the module, which has the problem, by WIDE or the service technicians who recommend by WIDE.
Here below is described what of the DDM monitor protocol is supported by an IDP2800SQ with Software version 3.0 or higher. Some of the DDM protocol related settings of the IDP2800SQ can be carried out through the IDP2800SQ OSD “Communication” menu (see 3.3.5.7.2). The protocol default setting is like following.
Page 69
Red On/Off (50h), Green On/Off (51h) and Blue On/Off (52h) The IDP2800SQ supports the DDM protocol commands Red On/Off, Green On/Off and Blue On/Off, and these are only turned on/off with the external signals – Analog RGB and DVI, but not with test pattern.
Page 70
But, almost bytes are for CRT based monitor like SONY DDM. But, IDP2800SQ support the status command and IDP2800SQ reply the pre-defined data of bytes not to be applicable. And also, the major system status and board status bytes are replaced with the status of IDP2800SQ system.
Page 71
Page No. Title IDP2800SQ 71 / 77 (SL28P2K) - Always 0x07. Byte 7 : Cursor’s current X position - Always 0x08 Byte 8 : Cursor’s current Y position - Always 0x08 Byte 9 : Major System status - Panel Status (OK : 0 / Warning or fault : 1)
Page 72
These commands not mentioned above are typical for CRT monitor and have no similar function in LCD monitor. These no-action commands are recognized by IDP2800SQ but cause no real action on the display. IDP2800SQ simply replies to the commands like following DDM monitor interface manual ...
73 / 77 (SL28P2K) Appendix C: Backlight Replacement Switch off the IDP2800SQ before carrying out a backlight replacement and disconnect the power cord and signal cables. Warning : Must remove the secondary power (Adapter) not to get shocked. The IDP2800SQ backlight lamp replacement instructions are depicted provisionally here below by means of pictures.
Page 74
Page No. Title IDP2800SQ 74 / 77 (SL28P2K) For replacing backlight trays, first, remove the screws to fix the metallic cover and put the cover out. And then, disconnect the cable between backlight assembly and an inverter. Issued Date Revision Status 2009-06-08 V5.3...
Page 75
Page No. Title IDP2800SQ 75 / 77 (SL28P2K) Backlight trays screws Then, remove the screws to fix the trays, and pull out the trays. The procedure to assemble is the exact reverse. Issued Date Revision Status 2009-06-08 V5.3...
76 / 77 (SL28P2K) Appendix D: Fan Replacement Switch off the IDP2800SQ before carrying out a fan replacement and disconnect the power cord and signal cables. Warning : Must remove the secondary power (Adapter) not to get shocked. The IDP2800SQ fan replacement instructions are depicted provisionally here below by means of pictures.
Page No. Title IDP2800SQ 77 / 77 (SL28P2K) Then pull off the fan connector from the board. Remove four screws of the fan to be changed. Then, change fans with new ones. The procedure to assemble is the exact reverse.