Download
Share
Print this page
Dynojet POWER COMMANDER V Installation Instructions
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Automobile Accessories
  5. Power commander V
  6. Installation instructions

Dynojet POWER COMMANDER V Installation Instructions

2014-2016 canam outlander 450
Hide thumbs Also See for POWER COMMANDER V:
1
2
3
4
5

Advertisement

Quick Links

Download this manual See also: Installation Instructions & Owner's Manual, Instruction and Installation Manual
2014-2016 CanAm Outlander 450
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
25-025
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro strips
1
Alcohol swab
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2014-2016 CanAm Outlander 450 - PCV - 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the POWER COMMANDER V and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Dynojet POWER COMMANDER V

Summary of Contents for Dynojet POWER COMMANDER V

  • Page 1 2014-2016 CanAm Outlander 450 Installation Guide I n s t a l l a t i o n I n s t r u c t i o n s Power Commander Decals Dynojet Decals Velcro strips Alcohol swab THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION!

  • Page 2: Usb Connection

    POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Switch Input #2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 (Grnd)
  • Page 3 FIG.A Remove the seat. Remove both side panels and the center cover (Fig. A). FIG.B Using the supplied velcro secure the PCV to the back of the airbox (Fig. B). Make sure to clean the surface with the alcohol swab before attaching. Ground wire FIG.C Route the PCV harness down towards the throttle body (Fig. C). 25-025 www.powercommander.com 2014-2016 CanAm Outlander 450 - PCV - 3...
  • Page 4 FIG.D Unplug the stock fuel injector connector (Fig. D). FIG.E Plug the PCV in-line of the stock injector and wiring harness (Fig. E). FIG.F Unplug the stock Throttle Position Sensor connector (Fig. F). 25-025 www.powercommander.com 2014-2016 CanAm Outlander 450 - PCV - 4...
  • Page 5 FIG.G Plug the connectors from the PCV in-line of the TPS and stock wiring harness (Fig. G). FIG.H Attach the ground wire from the PCV to the engine case bolt (Fig. H). 10 Reinstall the airbox and bodywork. 25-025 www.powercommander.com 2014-2016 CanAm Outlander 450 - PCV - 5...