Advertisement
Quick Links
Amtryke® ProSeries Model #1412
8 mm Socket or Wrench
13 mm Socket or Wrench
15 mm Socket or Wrench
Utility knife
Carton Contents
Carefully remove and lay out all parts from the carton so as not to scratch or lose any parts or pieces.
The shipping carton should contain:
1) Pedal Box – part PD-V3 ½ inch
2) Box marked with 0 and delta sign containing the seat assembly
3) Parts Box - The pictured items on the parts page.
4) The main frame assembly.
Revised Date: 11/04/08
50-FC-1412
Tools Needed for Assembly
10 mm deep well socket or wrench
14 mm Socket or Wrench
Needle Nose Pliers
Page 1 of 12
Advertisement
Related Manuals for AmTryke 1412
Summary of Contents for AmTryke 1412
- Page 1 Amtryke® ProSeries Model #1412 50-FC-1412 Tools Needed for Assembly 8 mm Socket or Wrench 10 mm deep well socket or wrench 13 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench Needle Nose Pliers Utility knife Carton Contents Carefully remove and lay out all parts from the carton so as not to scratch or lose any parts or pieces.
- Page 2 NOTE: THE SEAT POST ASSEMBLY MAY BE MOUNTED IN TWO (2) POSITIONS ON THE FRAME. THIS ALLOWS DIFFERENT POSITIONING BASED ON THE RIDERS SIZE. THE SEAT COMES MOUNTED IN THE BACK SET OF HOLES FROM THE FACTORY. a. Location of the seat post assembly may be adjusted. b.
- Page 3 Assembly Instructions 1) FRONT FORK TO MAIN FRAME ASSEMBLY To mount front fork onto main frame: a. Slide one of the ball bearing retainers onto the front wheel fork tube with ball bearings facing up. Then insert the fork tube into the main frame tube. b.
-
Page 4: Front Brake Assembly
2) FRONT BRAKE ASSEMBLY a. Front Brake – First take the nut, washer, and one contoured washer off of the brake. Insert brake bolt through hole in fork and reinstall counter washer, washer and nut. Make sure brake assembly is centered on fork before tightening. -
Page 5: Handlebar And Stem
3) HANDLEBAR AND STEM a) Remove black plastic cap from handle bar stem. Insert stem of handlebar assembly into fork head tube. **NOTE: THE STEM MUST BE INSERTED INTO THE FORK HEAD TUBE TO AT LEAST THE MINIMUM INSERTION LINE. b) Secure stem by tightening stem expander hex head bolt (located under the gray plastic cover at top of stem –... -
Page 6: Brake Lever Installation
4) BRAKE LEVER INSTALLATION a) Mount hand brake lever to comfortable position on the handlebars for your rider. Trim foam grip to allow clearance for desired brake position. b) Open the brake lever and place the nipple end of the brake cable into the lever, then close the lever. - Page 7 5) SEAT POST FRAME ASSEMBLY a) Slide seat post assembly into slanted tube on main frame. Pull back on spring loaded knob and let pin seat into desired hole on seat post assembly. NOTE: Seat post knob is never removed. Simply loosen, pull out on spring loaded knob, and then tighten once pin is in desired hole position.
- Page 8 7) BASKET ASSEMBLY a) Bars at rear of basket mount onto bracket at back of tryke. Two screws and nuts (black) can secure basket if rider desires permanent attachment. 8) PEDALS NOTE: there is a right and left pedal indicated by an L or R on the end of each pedal axle.
- Page 9 9) STEERING PIN INSTALLATION a) The steering inserts into the front fork tube from the side. b) The top position locks the steering straight. This allows for easy transfer or if the child needs assistance with learning to steer properly. c) The lower position limits the steering to 20 degrees in either direction.
- Page 10 Friend of AMBUCS™. Your contribution of $25 or more will combine with other donations to buy a child on our Wish List an AmTryke® therapeutic tricycle. It’s easy to become a Friend of AMBUCS™. You can use the handy form included with the assembly packet or go online at www.ambucs.org.
Need help?
Do you have a question about the 1412 and is the answer not in the manual?
Questions and answers