Xray X10 Instruction Manual
  1. Manuals
  2. Brands
  3. Xray Manuals
  4. Motorized Toy Car
  5. X10 Link
  6. Instruction manual

Xray X10 Instruction Manual

1/10 pan car
Hide thumbs Also See for X10:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X10 and is the answer not in the manual?

Questions and answers

Related Manuals for Xray X10

Summary of Contents for Xray X10

  • Page 2: Customer Support

    Make sure you review this entire manual, download and use set-up book from racing car is not intended for use by beginners, inexperienced customers, or the web, and examine all details carefully. If for some reason you decide The X10 by children without direct supervision of a responsible, knowledgeable adult.

  • Page 3: Warranty

    Over-charging, incorrect charging, or using inferior R/C & BUILDING TIPS Please support your local hobby shop. We at XRAY Model Racing Cars support all local • Make sure all fasteners are properly tightened. Check them periodically. • Make sure that chassis screws do not protrude from the chassis.

  • Page 4: Symbols Used

    (HUDY #107600) (HUDY #107601) EQUIPMENT INCLUDED NOT INCLUDED HUDY Premium Silicone Diff Grease XRAY offers wide range of optional tuning parts SAMPLE OF Oil 700cSt (#106370) (HUDY #106211) which are listed in tables like these. Please refer OPTIONAL PARTS Oil 10000cSt (#106510)
  • Page 5 GRAPHITE PART PREPARATION PREPARE ALL GRAPHITE PARTS To protect and seal edges of graphite parts, sand edges smooth and then apply CA glue. Fine sandpaper Use fine sandpaper to sand smooth the edges of all graphite parts. Apply CA glue to all adges of the graphite parts.

  • Page 6: Front Suspension

    372316-O 373241 372180 #372131 HARD INCLUDED 965019 372122 372294 303121-O 372293 #371014 372292 X10’18 ALU FLEX 2.0MM CHASSIS - 7075 T6 ALU ECCENTRIC BUSHINGS M3 NUTS #960030 STEEL SILVER INCLUDED #372316-O 0mm INCLUDED #372317-O 0.5mm OPTION #960031 SILVER OPTION #296530-O ALU ORANGE OPTION #372318-O 1.0mm...
  • Page 7 1. FRONT SUSPENSION UPPER SUSPENSION ARMS #372130 MEDIUM OPTION #372131 HARD INCLUDED NOTE ORIENTATION STEEL BALL 5.2mm 5.2mm NOTE DETAIL DETAIL CAMBER ORIENTATION If the arm does not have enough play, remove the clips and thin DETAIL 901304 the clips slightly with sandpaper. SB M3x4 The arms must have free movement and not bind.
  • Page 8 RIDE HEIGHT enough material so you can insert #372179 C=3.0 GREY OPTION #372183 C=5.5 GREY OPTION the kingpin without a lot of force. #371014 X10’18 ALU FLEX 2.0MM CHASSIS - 7075 T6 903312 SFH M3x12 960030 N M3 M3 NUTS...

  • Page 9: Rear Suspension

    373094 902306 371190 303241 903306 903306 903306 #371156 X10 ALU 2.0MM REAR POD LOWER PLATE - 7075 T6 303241 BALL UNIVERSAL 5.8 MM HEX (4) 373590 COMPOSITE SPRING HOLDER (2) 306219 COMPOSITE SET OF SERVO SHIMS (4) 373591 COMPOSITE SIDE SPRING HOLDER (2) 371076 X10’18 REAR BRACE - GRAPHITE 2.5MM...
  • Page 10 3. REAR SUSPENSION NOTE 902306 ORIENTATION SH M3x6 903306 SFH M3x6 Lightly tighten the screws so there is no free play, but do not overtighten otherwise the ball will not move freely. 902306 DETAIL SH M3x6 Ensure free, smooth movement without excessive freeplay.
  • Page 11 3. REAR SUSPENSION POD Linkage position DETAIL NOTE ORIENTATION Ensure free, 903306 smooth movement SFH M3x6 OUTER POSITION - (INITIAL SETTING) the side link is straight, easier to drive INNER POSITION - the side link is angled, increased in-corner steering TIGHTEN FULLY DETAIL NOTE ORIENTATION...
  • Page 12 3. REAR SUSPENSION 306219 3x6mm SHIM 3x6x1 3x6mm 902306 SH M3x6 BLACK nut M3 902308 SH M3x8 3x8mm 903306 ALTERNATIVE 1 ALTERNATIVE 2 SFH M3x6 SHORT SHOCK LONG SHOCK FORWARD MOUNT POSITION REARWARD MOUNT POSITION "SHORT SHOCK" INITIAL SETTING 960032 N M3 3x6mm "LONG SHOCK"...

  • Page 13: Ball Differential

    CARBIDE BALL-BEARING AXIAL F3-8 3x8x3.5 375012 STEEL REAR AXLE SHAFT - HUDY SPRING STEEL™ 930230 CERAMIC BALL 3.175MM (12) (OPTION) 375035 X10 ALU REAR WHEEL HUB - RIGHT 930238 CERAMIC BALL-BEARING AXIAL F3-8 3x8x3.5 (OPTION) 375045 X10 ALU REAR WHEEL HUB - LEFT 941438 HIGH-SPEED BALL-BEARING 1/4“x3/8“x1/8“...
  • Page 14 4. BALL DIFFERENTIAL Depending on the tires and their diameter, there are three ways to mount the alu upper clamp: 303140-O NOTE SHIM 3x5x2 ORIENTATION 1. Shims above clamp. 303141-O SHIM 3x5x1 2. Shims between clamp and bulkhead. 303142-O SHIM 3x5x0.5 3.

  • Page 15: Shock Absorber

    5. SHOCK ABSORBER SHOCK SPRINGS #378092 C=1.5 SILVER OPTION #378093 C=1.8 GOLD INCLUDED 378050-O #378094 C=2.1 BLACK OPTION #378095 C=1.4-1.9 BLACK OPTION 378080 #378096 C=2.0-2.5 BLACK OPTION 378011 378011 378060 965015 965015 971022 HUDY SHOCK OILS 378030-O #106310 100cSt 378020 #106315 150cSt 378093...
  • Page 16 5. SHOCK ABSORBER 971022 O 2x2 Shock Oil Shock Oil DEFAULT SHOCK SETTING FOR CENTER SHOCK ABSORBER Follow the steps below to set the shock. HALF TIGHTEN TIGHTEN FULLY 100% 700cSt 3~5x UP & DOWN ➐ Keep the shock shaft ➊...
  • Page 17 5. SHOCK ABSORBER ALTERNATIVE 1 - SHORT SHOCK ALTERNATIVE 2 - LONG SHOCK (INITIAL SETTING) For the LONG shock alternative, use the shock adaptor. 901303 901303 SB M3x3 SB M3x3 By using longer or shorter shock, the damping and steering characteristics can be changed. SHORT SHOCK: LONG SHOCK: Shock is built WITHOUT adaptor.

  • Page 18: Final Assembly

    HEX SCREW SB M3x3 (10) 309402 BODY CLIP FOR 6MM BODY POST (4) 902308 HEX SCREW SH M3x8 (10) 371040 X10 GRAPHITE 2.5MM FRONT BUMPER & SHIMS - V2 902310 HEX SCREW SH M3x10 (10) 371225 X10 FOAM BUMPER 903305...
  • Page 19 6. FINAL ASSEMBLY ALTERNATIVE 2 ALTERNATIVE 1 - MID size servo - STANDARD size servo (OPTIONAL) (INITIAL SETTING) 306219 OPTIONAL INCLUDED SHIM 3x6x2 STANDARD size servo MID size servo (NOT INCLUDED) (NOT INCLUDED) 903310 SFH M3x10 For basic set-up use For basic set-up use 3x6x2mm composite shims.
  • Page 20 6. FINAL ASSEMBLY 35.7mm 35.7mm Left thread Left thread NOTE ORIENTATION Note groove position NOTE ORIENTATION Note groove position 902310 SH M3x10 981212 P 2x12 The bodies for 1/10 pan cars are available in different lengths. The bumper position depends on the 903308 length of the body.
  • Page 21 6. FINAL ASSEMBLY 981212 P 2x12 Pinion (NOT INCLUDED) PINION GEARS ALU HARDCOATED #305968 18T / 64P OPTION Motor 902308 (NOT INCLUDED) #305969 19T / 64P OPTION SH M3x8 #305970 20T / 64P OPTION #305971 21T / 64P OPTION #305972 22T / 64P OPTION #305973...
  • Page 22 6. FINAL ASSEMBLY ELECTRONICS CONFIGURATION: REARWARD POSITION INITIAL POSITION) 903305 SFH M3x5 Battery Pack When inserting or removing batteries, (NOT INCLUDED) remove graphite plate for mounts and antenna holder. Receiver Speed Controller (NOT INCLUDED) (NOT INCLUDED) Double-sided Tape (HUDY #107875) (NOT INCLUDED) ELECTRONICS CONFIGURATION: FORWARD POSITION...
  • Page 23 6. FINAL ASSEMBLY M3 NUTS #960030 STEEL SILVER INCLUDED 375390 #960031 SILVER OPTION ALU SCH M3x8 #296530-O ALU ORANGE OPTION 901304 SB M3x4 951851 BB 1/8“x5/16“x9/64“ 960030 N M3 Fibre Tape Receiver Wire (HUDY #107870) (NOT INCLUDED) Rear Wheels & Tires (NOT INCLUDED) Front Wheels &...
  • Page 24 RC AMERICA, 2030 Century Center Blvd #15, Irving, TX 75062, USA PHONE: 214-744-2400, FAX: 214-744-2401, xray@rcamerica.com...

Table of Contents