Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for NTC RZ113
- Page 1 NTC STAVEBNÍ TECHNIKA spol. s r.o. Jiřinková 120, 552 03 Česká Skalice Czech Republic Tel.: +420 491 452 184 fax: +420 491 401 609 E-mail: ntc@ntc.cz www.ntc.cz OPERATION MANUAL ASPHALT AND CONCRETE CUTTERS RZ113, RZ123 (version 01/2017)
- Page 2 Prohlašujeme, že zařízení definované níže uvedenými údaji je ve shodě s požadavky níže uvedených NV a směrnic We declare that the trough below mentioned specifications defined equipment complies with requirements of below cited Directives Výrobce (manufacturer): NTC STAVEBNÍ TECHNIKA spol. s r.o. Sídlo firmy (company domicile): Jiřinková 120, Česká Skalice 552 03 IČ...
-
Page 3: Table Of Contents
Phone: +420 491 452 184, fax: +420 491 401 609 E-mail: ntc@ntc.cz NTC STAVEBNÍ TECHNIKA spol. s r.o. is a light construction equipment manufacturer with a long- term experience. NTC machines are exported to many European countries, among others to Spain, Netherlands, Italy, Hungary, Romania and Russia. - Page 4 Asphalt and concrete cutters Operation manual 4.1.1. Gasoline Engines HONDA ........................14 4.2..............................14 PERATION 4.2.1. Selection of the Cutting Disc ......................... 14 4.2.2. Fastening of the Cutting Disc ........................ 15 4.2.3. Cutting ..............................15 4.2.4. Cutting Depth Scale ..........................15 4.3.
-
Page 5: Safety Instructions
Asphalt and concrete cutters Operation manual SAFETY INSTRUCTIONS 1.1. General instructions for operation of light construction equipment 1.1.1. Requirements for qualification of the operator 1. The machine must be operated by 2. The operator is obliged to use suitable trained reliable operators of age above working dress, safety gloves and firm boots 18. -
Page 6: Operation Of The Machine
Asphalt and concrete cutters Operation manual 1.1.4. Operation of the machine DANGER! Leaking fuel tank and distribution Before starting: may cause explosion. Replace these parts 1. Check the machine thoroughly, repair all immediately if damaged. failures before starting the engine. If the failures cannot be repaired at the jobsite, do Jobsite: not operate the machine. -
Page 7: Prohibited Activities
Asphalt and concrete cutters Operation manual 1.2. Prohibited activities operate the machine within the protective Never: use the machine for other than intended range of power lines or transformer purposes stations use the machine in other way than as ... -
Page 8: Liquidation Of The Machine
NTC bears no responsibility for any damages environmental protection. caused by breaking above mentioned hygienical Metal parts must be disposed only by and ecological rules. authorized companies. 1.6. Safety Instructions Besides of general safety instruction, the 5. -
Page 9: List Of Safety Marks Used On The Machine
Asphalt and concrete cutters Operation manual 1.8. List of safety marks used on the machine In accordance to requirements of law no 22/1997 Sb. About technical requirements on products in valid version, there are stickers of safety marks and informative symbols placed on the machines (types – see point 2.1). Types of the stickers are explained further, explanation is attached to each symbol. -
Page 10: Technical Description
1.9 Dispose of packing material NTC STAVEBNI TECHNIKA spol. s r.o. is registered by company EKO-KOM a.s. There is an agreement done for redemption of packing materials with EKO-KOM a.s. by NTC STAVEBNI TECHNIKA spol. s r.o. or packing materials suppliers. -
Page 11: Basic Technical Data
Asphalt and concrete cutters Operation manual 2.1. Basic Technical Data: RZ 113 RZ 123 Cutting depth (mm) Cutting disc fastening at right at right Max. disc dia (mm) Travel manual manual Cutting depth adjust. manual Fastening hole dia (mm) 25,4 25,4 Spindle speed (RPM) -
Page 12: Identification
Asphalt and concrete cutters Operation manual Fig. Machine decal 2.3. Identification For communication with the manufacturer (i.e. for warranty claims, service requests, spare parts ordering) always report exact model and serial number of your machine. These data are stamped on the machine decal. 2.4. -
Page 13: Visual Inspection Of The Machine
Asphalt and concrete cutters Operation manual 3.2. Visual Inspection of the Machine free motion of the cutting disc spindle Check regularly the machine for: missing parts Pay special attention to safety devices (covers) released bolts and screws and controls. -
Page 14: Operation
Asphalt and concrete cutters Operation manual OPERATION 4.1. Starting 4.1.1. Gasoline Engines HONDA 1. Turn the fuel tap into the ON position. 2. Turn on the electric switch of ignition. 5. Pull out the starter grip slowly till some resistance is felt, then pull vehemently. Do not release the grip, but return it slowly into the original position. -
Page 15: Fastening Of The Cutting Disc
Asphalt and concrete cutters Operation manual 4.2.2. Fastening of the Cutting Disc 1. Turn off the engine and open the disc cover. 2. Use the enclosed wrenches to hold the spindle and unscrew the fastening nut. NOTE: Left thread! 3. Fit the cutting disc on the spindle and secure 4. -
Page 16: H Andling , T Ransport , S Toring
Asphalt and concrete cutters Operation manual 4.4. Handling, Transport, Storing When handling the machine keep safety general safety rules valid for operation of lifting regulation shown in this manual and well as or hoisting equipment. 4.4.1. Manual Handling For manual lifting, cooperation of mode people is required. -
Page 17: Maintenance
Asphalt and concrete cutters Operation manual MAINTENANCE The basic activities of maintenance, which are described in this Manual can be carried out by the designated operator. Repairs and adjustments beyond the extent of this Manual should be committed to an authorized service. It is forbidden to intervent the engine (except for standart maintenance) during warranty period. -
Page 18: Maintenance Schedule
To be carried more often when operating in dusty environment!!! Such maintenance should be performed by service technicians NTC, respectively. authorized service according to engine type, especially if the user does not have the proper tools and knowledge about these devices. -
Page 19: Warranty Conditions
7. WARRANTY CONDITIONS Construction machines manufactured by NTC are designed and manufactured to suit longterm operation by most difficult conditions. Based on our experience we can say that these machines do work reliably not during the warranty period but also long time after the warranty expires. - Page 20 Please send properly filled protocol by fax, e-mail or post to above mentioned address, you will speed the process up! Accepting the warranty (to be filled in by warranty dept. of NTC): Date of repair start: Date of repair...
- Page 21 Used spare parts: Part no. Description Tech. director sign. Production director sign Finishing warranty management (to be filled by warranty dept. of NTC): Arranged by: Way of transport: Shipment date: Returning the machine to owner (in case of repair in...
- Page 22 Asphalt and concrete cutters Operation manual Page 22 issued 01/2017...
Need help?
Do you have a question about the RZ113 and is the answer not in the manual?
Questions and answers