Advertisement
801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 •
www.sdcsecurity.com • E-mail: service@sdcsecurity.com
ALUMINUM FRAME MOUNT CONFIGURATION
.865
1.755
O1.150
1.500
NOTE: TEMPLATE DIMENSIONS ARE SUBJECT TO
CHANGE WITHOUT NOTICE.
TECHNICAL DATA (FOR STANDARD UNIT)
FACE PLATE: 10-1/2" x 1-1/2" X 1/8"
STRIKE: 4" x 1-1/2" x 1/8"
ID REQUIREMENTS: 10-1/2" x 1-1/2" x 1-1/2"
BOLT: 5/8" DIA. STAINLESS STEEL
BOLT THROW: 3/4"
P:\INSTALLATION INST\Electric Bolt Locks\TEMP-1091A\Temp-1091ADMR.vsd
1091ADMR
INSTALLATION INSTRUCTIONS/TEMPLATE
MECHANICAL RELEASE
.750
11.605
10.500
REV A
(8X) TAP TABS
FOR #10-32
CYLINDER NOT
INCLUDED
1.51
.750
(2X) TAP FOR #10-32
4.00
L C OF BOLT
1.50
.125
09-17
Page 1
Door Preparation
3.25
4.00
L C OF DOOR
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email engineer@sdcsecurity.com
Advertisement
Table of Contents
Related Manuals for SDC Spacesaver 1091 ADMR
Summary of Contents for SDC Spacesaver 1091 ADMR
- Page 1 801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 • www.sdcsecurity.com • E-mail: service@sdcsecurity.com 1091ADMR INSTALLATION INSTRUCTIONS/TEMPLATE MECHANICAL RELEASE ALUMINUM FRAME MOUNT CONFIGURATION (8X) TAP TABS .750 FOR #10-32 .865 CYLINDER NOT INCLUDED 1.755 11.605 O1.150 10.500 Door Preparation 1.500 1.51 .750 (2X) TAP FOR #10-32...
- Page 2 HOLLOW METAL MOUNT CONFIGURATION (8X) TAP TABS .865 .750 FOR #10-32 CYLINDER NOT INCLUDED 1.755 11.605 O1.150 10.500 Door Preparation 1.500 1.51 .750 (2X) TAP FOR #10-32 4.00 NOTE: TEMPLATE DIMENSIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 3.25 4.00 L C OF BOLT TECHNICAL DATA (FOR STANDARD UNIT) FACE PLATE: 10-1/2"...
- Page 3 DOOR MOUNT CONFIGURATION .865 .750 Door Preparation (8X) TAP TABS FOR #10-32 CYLINDER NOT INCLUDED 1.755 O1.150 11.605 10.500 Frame Preparation 1.51 .750 1.500 4.00 3.25 (2X) TAP #10-32 4.00 BOLT NOTE: TEMPLATE DIMENSIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 1.50 TECHNICAL DATA (FOR STANDARD UNIT) FACE PLATE: 10-1/2"...
- Page 4 INSTRUCTIONS FOR REVERSING THE CYLINDER Cylinder Locking Remove the Cylinder locking set screw, and screw the Set Screw Cylinder out of the Mounting Block. Remove the four screws securing the Mounting Block and the Sliding Link Block. Mounting Block Sliding Link Block Reverse the components and re-install as shown.
- Page 5 LOCK WIRING Select 24VDC OR 12VDC Configuration, and use provided pigtail connector: 24VDC SOLENOID 24VDC CONFIGURATION POWER Access INPUT Control or YEL (+) Push Button NOTE: Cap FROM (N/C) PIGTAIL unused wires LOCK CONNECTOR (PRE- WIRED) WHT (-) ELECTRICAL DATA: Dual Voltage Solenoid 12VDC@ .9 mA (max.) 24VDC@ .45 mA (max.)
Need help?
Do you have a question about the Spacesaver 1091 ADMR and is the answer not in the manual?
Questions and answers