Related Manuals for Graco Dream Suite
Summary of Contents for Graco Dream Suite
- Page 1 Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE. Dream Suite ™...
- Page 2 • In gaps between extra padding and side of the product, and • On soft bedding. Use ONLY mattress/pad provided by Graco. NEVER add a pillow, comforter or another mattress for padding. • Product can roll over on soft surfaces and suffocate child.
- Page 3 • If a sheet is used with the pad use only the one provided by • STRANGULATION HAZARD: Graco or one specifically • Never place baby face down on designed to fit the dimensions of the changing table. the product.
- Page 4 FOR SAFE BATTERY USE: Keep the batteries out of children’s reach. Any battery may leak battery acid if mixed with a different battery type, if inserted incorrectly (put in backwards) or if all batteries are not replaced or recharged at the same time. Do not mix old and new batteries.
- Page 5 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 6 2-A Parts list This model may not include some features shown below. Check that you have all the parts for this model BEFORE assembling your product. If any parts are missing, call Customer Service. Tools required: Philips Screwdriver ALL MODELS Toy styles may vary...
- Page 7 Position Handle Position Handle is assembled to foot end of bassinet/changer. NOTE: Start assembly with the Button handle in this orientation. If it is not Botón in this orientation, follow steps 1-2. 1. Slide button inside of handle up and squeeze.
- Page 8 2. Rotate handle until it clicks into place. SNAP!
- Page 9 Bassinet/changer Assembly Head End 1. Lay bassinet/changer on floor Head End with canopy facing down. CHECK tube is inserted in channel above mesh exactly as shown. 2. MAKE SURE that webbing straps between pad and leg hub are not twisted. Insert tube into the top channel of leg hub in head end of bassinet/ changer as shown.
- Page 10 3. CHECK tube is inserted in channel Head End above mesh exactly as shown. 4. Insert tube into the top channel of leg hub in head end of bassinet/changer as shown. The metal button should be facing out when snapped in place as shown.
- Page 11 5. Flip bassinet/changer over so side Head End with the canopy is facing up. CHECK tube with grooves is inserted exactly as shown. Groove 6. Insert tube with grooves into the top channel of leg hub in head end of bassinet/changer as shown.
- Page 12 7. CHECK tube with grooves is Head End inserted exactly as shown. Groove 8. Insert tube with grooves into the top channel of leg hub in head end of bassinet/changer as shown. The metal button should be facing out when snapped in SNAP! place as shown.
- Page 13 9. CHECK that leg tube with handle is rotated as shown, if not see 3-A. 10. Attach end of tube with groove on the foot end of bassinet/ changer into top channel of leg hub with handle. The metal button should be facing out when snapped in place as shown.
- Page 14 11. Attach other tube with groove on the foot end of bassinet/changer into top channel of leg hub with handle. The metal button should be facing out when snapped in place as shown. Foot End SNAP! 12. Flip bassinet/changer back to changer side.
- Page 15 11. Insert covered mattress into bassinet. 12. Press down on mattress pad to be sure hook and loop tape is attached.
- Page 16 13. Attach legs to bassinet/changer as shown. SNAP! SNAP!
- Page 17 14. Attach other two legs to bassinet/changer as shown. SNAP! SNAP!
- Page 18 15. Insert end tubes into channels in storage as shown. 16. Insert ends of tubes into corners of long tubes as shown. SNAP! SNAP!
- Page 19 17. Insert other ends of tubes into corners of long tubes as shown. SNAP! SNAP! ¡CRAC! 18. Stand bassinet/changer up. NOTE: DO NOT use bassinet/changer without storage attached.
- Page 20 19. Place storage under bassinet/ changer. Insert tabs into larger end of channels in legs and press down firmly until they secure into place. Repeat on all four legs. 20. CHECK that tabs are pushed all the way down to the bottom of the channels in legs by pulling on them.
- Page 21 Canopy 1. (A) Slide button inside of handle up and squeeze then (B) press button on top of handle. Rotate changer over to bassinet side. Press down on side of bassinet and handle to make sure bassinet/changer is locked into mode.
- Page 22 Switching Modes Bassinet Mode • Modo 1. (A) Slide button inside of handle up and squeeze then (B) press button on top of handle. 2. Rotate changer over to bassinet side. Press down on side of bassinet and handle to make sure bassinet/changer is locked into mode.
- Page 23 3. To open canopy, attach hook and loop tape on both sides as shown. Changer Mode 1. Slide button inside of handle up and squeeze.
- Page 24 2. Rotate over to changer side. Press down on center of changer side to make sure bassinet/changer is locked into mode. SNAP!
- Page 25 Canopy 1. Disconnect hook and loop tape on canopy flaps from sides of the bassinet. 2. Connect strap on head end of bassinet to tab in center of canopy.
- Page 26 Brakes • Frenos 1. Push tab up on all four wheels to unlock. 2. Push tab down on all four wheels to lock.
- Page 27 To Use Vibration 1. Remove battery lid on the foot end of product, with a philips screwdriver and insert 1-D (LR20-1.5V) battery in module. Replace lid. 2. Vibration: To use vibration, slide button to left or right for hi or lo speed.
- Page 28 • FROM TIME TO TIME CHECK YOUR PRODUCT for loose screws, worn parts, torn material or stitching. Replace or repair the parts as needed. Use only Graco replacement parts. • TO CLEAN PRODUCT, wipe clean with damp cloth. • TO CLEAN FRAME, use only household soap and warm water.
- Page 29 To Clean Mattress cover 1. Remove mattress from bassinet. 2. Separate hook and loop tabs and remove mattress pad from mattress cover. See label on mattress cover for proper cleaning.