Download Print this page

Advertisement

Dell Vostro 15-7570
Owner's Manual
Regulatory Model: P71F
Regulatory Type: P71F001

Advertisement

   Summary of Contents for Dell Vostro 15-7570

  • Page 1

    Dell Vostro 15-7570 Owner's Manual Regulatory Model: P71F Regulatory Type: P71F001...

  • Page 2

    A WARNING indicates a potential for property damage, personal injury, or death. © 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.

  • Page 3

    Chassis This chapter illustrates the multiple chassis' view along with the ports and connectors and also explains the function hot key combinations. Topics: • Front open view • Left view • Right view • Palmrest view • Back view • Bottom view •...

  • Page 4

    Camera status light Dual array microphones Display panel LED status light Left view Nobel Wedge lock slot Power connector Network connector USB 3.1 Gen 1 port SD card reader Right view Headset/Mic port USB 3.1 Gen 1 port USB 3.1 Gen 1 port USB Type-C port with Thunderbolt 3 HDMI port VGA port...

  • Page 5

    Palmrest view Power button/Fingerprint reader Keyboard Palmrest Touchpad Chassis...

  • Page 6

    Back view Air vent Air vent Bottom view Chassis...

  • Page 7

    Speakers Back cover Air vent Service tag label Air vent Keyboards hot key definitions Table 1. Keyboard hot key combination Fn Key Combination Function Fn+ESC Fn Toggle Fn+ F1 Speaker Mute Fn + F2 Volume Down Fn + F3 Volume Up Fn + F4 Previous track Fn + F5...

  • Page 8

    CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers. Connect any external devices, such as a port replicator or media base, and replace any cards, such as an ExpressCard.

  • Page 9

    Base cover Removing the base cover Follow the procedure in Before working inside your computer. To remove the base cover: Loosen the M2.5x2+3.5 captive screws that secure the base cover to the computer [1]. b Pry the base cover from the edge [2]. NOTE: You may need a plastic scribe to pry the base cover from the edge.

  • Page 10

    Installing the base cover Align the base cover with the screw holders on the computer. Press the edges of the cover until it clicks into place. Tighten the M2.5x2+3.5 screws to secure the base cover to the computer. Follow the procedure in After working inside your computer.

  • Page 11

    Lift the battery away from the computer. Installing the battery Insert the battery into the slot on the computer. Connect the battery cable to the connector on the battery. Removing and installing components...

  • Page 12

    Tighten the M2x3L screws to secure the battery to the computer. Install the base cover Follow the procedure in After working inside your computer. Coin cell battery Removing the coin cell battery Follow the procedure in Before working inside your computer.

  • Page 13

    Memory modules Removing the memory module Follow the procedure in Before working inside your computer. Remove the: base cover battery To remove the memory module: Pry the clips securing the memory module until the memory pops-up [1]. b Lift the memory module away from the connector [2]. Installing the memory module Insert the memory module into the memory module socket until the clips secure the memory module.

  • Page 14

    Hard drive Removing the hard drive Follow the procedure in Before working inside your computer. Remove the: base cover battery To disconnect the cable: Lift the latch and disconnect the hard drive cable from the computer [1]. b Pry the hard drive cable to release from the adhesive [2]. To remove the hard drive: Remove the M2.5x5L screws that secure the hard drive to the computer [1].

  • Page 15

    Installing the hard drive Insert the hard drive into the slot on the computer. Replace the M2.5x5L screws to secure the hard drive assembly to the computer. Affix the hard drive cable on the computer. Connect the hard drive cable to the connector on the hard drive and on the system board. Install the: battery base cover...

  • Page 16

    Installing the M.2 Solid State Drive — SSD Insert the SSD into the connector on the computer. Replace the M3x3L screw to secure the SSD to the computer. Install the: battery base cover Follow the procedure in After working inside your computer.

  • Page 17

    Disconnect the WLAN cables from the connectors on the WLAN card [3]. d Lift the WLAN card away from the connector [4]. Installing the WLAN card Insert the WLAN card into the slot on the computer. Connect the WLAN cables to the connectors on the WLAN Card. Place the bracket and replace the M2x3L screw to secure it to the computer.

  • Page 18

    b Pry the rear cover from the edge [2]. NOTE: You may need a plastic scribe to pry the rear cover from the edge. Pry the edges of the rear cover using a plastic scribe. Removing and installing components...

  • Page 19

    Remove the rear cover from the computer. Installing the rear cover Press the edges of the rear cover until it clicks into place. Tighten the M2x2L(OD7) screws to secure the rear cover to the computer. Removing and installing components...

  • Page 20

    Install the: battery base cover Follow the procedure in After working inside your computer. Back cover Removing the back cover Follow the procedure in Before working inside your computer. Remove the: base cover battery To disconnect the cables: Disconnect the camera cable and unroute from the routing channel [1, 2]. b Disconnect the WLAN cable and unroute from the routing channel [3, 4].

  • Page 21

    Disconnect the following cables: Disconnect the Power, LED and Keyboard backlight cable from the connector [1]. b Disconnect the touchpad cable from the connector [2]. Remove the white adhesive tape and disconnect the keyboard cable from the connector [3, 4]. Removing and installing components...

  • Page 22

    Remove the M2.5xL6 (19) screws that secure the back cover to the computer. Removing and installing components...

  • Page 23

    Remove the M2L3(4) screws and turn over the system [1, 2]. Open the display assembly at 90° angle. Removing and installing components...

  • Page 24

    To remove the back cover: Using a plastic scribe, pry the edges of the plamrest [1, 2]. b Lift the plamrest away from the back cover [3]. Removing and installing components...

  • Page 25

    The component you are left with is the back cover. Removing and installing components...

  • Page 26

    Installing the back cover Press the edges of the back cover until it clicks into place. Close the display assembly and turn over the system. Replace the M2L3(4) and M2.5xL6 (19) screws to the back cover to the computer. Connect the power, LED and Keyboard backlight cable, touchpad, keyboard cable and affix the white adhesive tape to the connector to the computer.

  • Page 27

    To remove the speaker: Disconnect the speaker cable [1]. b Unroute the cable from routing channel [2, 3, 4]. Lift the speakers, along with the speaker cable, and remove it away from the back cover. Removing and installing components...

  • Page 28

    Installing the speaker Align the speakers along the slots on the computer. Route the speaker cable through the routing tabs on the computer. Connect the speaker cable to the system board. Install the: back cover rear cover memory module SSD card battery base cover Follow the procedure in...

  • Page 29

    Disconnect the coin cell battery cable from the connector [1]. b Disconnect the hard drive cable from the connector [2]. Remove the following metal tab: Remove the M2.5xL5(2) screws that secure the metal tab on the system board [1]. b Lift the metal tab that secures the power port on the system board [2]. Remove the M2.5xL5(2) screws that secure the metal tab on the system board [3].

  • Page 30

    Remove the M2x3L(4) screws that secure the system fan to the system board. Removing and installing components...

  • Page 31

    To remove the system board: Remove the 2.5x5L(3) screws that secure the system board to the computer [1]. b Lift and remove the system board from the computer [2]. Installing the system board Align the system board into its original position on the computer. Replace the 2.5x5L (3) screws to secure the system board to the computer.

  • Page 32

    Power connector port Removing the power connector port Follow the procedure in Before working inside your computer. Remove the: base cover battery SSD card memory module rear cover back cover system board To remove power connector port: Unroute the power connector port from the routing channel [1]. b Remove the power connector port from the computer [2].

  • Page 33

    Installing the power connector port Place the power connector port on the computer. Route the power connector port cable through the routing channels on the computer. Install the: system board back cover rear cover memory module SSD card battery base cover Follow the procedure in After working inside your computer.

  • Page 34

    To remove the heat sink assembly: Turn over the system board and remove the M2x3L(6) screws that secure the heat sink assembly to the system board [1]. NOTE: Loosen the screws based on the numbering on the heat sink. b Lift the heat sink assembly from the system board [2]. The component you are left with is the heat sink assembly.

  • Page 35

    NOTE: Tighten the screws based on the order mentioned in the removal procedure. Turn over the system board. Connect the heat sink assembly cable to the system board. Install the: back cover rear cover memory module SSD card battery base cover Follow the procedure in After working inside your computer.

  • Page 36

    Installing the touchpad Place the touchpad into the slots on the display assembly. Replace the M2x2L (4) screws that secure touchpad on the display assembly. Install the: back cover rear cover memory module SSD card battery base cover Follow the procedure in After working inside your computer.

  • Page 37

    Slide and lift the LED board from the display assembly [3]. Installing the LED board Place the LED board into the slots on the display assembly. Replace the M2x3L screw that secures LED board on the display assembly. Connect the LED board cable to the display assembly. Install the: back cover rear cover...

  • Page 38

    SSD card memory module rear cover back cover To release the power button board: Lift the latch and disconnect the power button board cable [1]. b Peel of the power button board cable from the adhesive [2]. To remove power button board: Remove the M2x3L (2) screws that secure the power button board [1].

  • Page 39

    Installing the power button board Place the power button board into the slots on the display assembly. Replace the M2x3L (2) screw that secures power button board on the display assembly. Connect the power button board cable to the display assembly. Install the: back cover rear cover...

  • Page 40

    base cover battery SSD card memory module rear cover back cover To release the fingerprint reader: By using a plastic scribe lift the fingerprint reader board [1]. b Remove the M2x2 screws that secure the fingerprint reader to the palm rest [2]. Lift the fingerprint reader away from the palm rest [3].

  • Page 41

    Keyboard Removing the keyboard Follow the procedure in Before working inside your computer. Remove the: base cover battery SSD card memory module rear cover back cover display hinge Disconnect the following cables: power board cable b LED board cable keyboard backlight cable d touchpad cable keyboard cable Remove the M1.6x2.2L (30) screws and lift the keyboard [1, 2].

  • Page 42

    Remove the keyboard from the palm rest. Installing the keyboard Place the keyboard into the slots on the palm rest. Replace the M1.6x2.2L (30) screws that secure keyboard on the palm rest. Connect the following cable to the display assembly. power board cable Removing and installing components...

  • Page 43

    b LED board cable keyboard backlight cable d touchpad cable keyboard cable Install the: display hinge back cover rear cover memory module SSD card battery base cover Follow the procedure in After working inside your computer. Display assembly Removing the display assembly Follow the procedure in Before working inside your computer.

  • Page 44

    Slide and lift the display assembly. The component you are left with is the display assembly. Removing and installing components...

  • Page 45

    Installing the display assembly Place the display assembly on the computer. Place the hinge bracket on the display assembly. Replace the M2.5x5L(2) screws that secure the hinge bracket to the display assembly. Install the: back cover rear cover memory module SSD card battery base cover...

  • Page 46

    Install the following components on the new palm rest. display hinge display assembly keyboard fingerprint reader power button board LED board touchpad back cover rear cover WLAN card hard drive memory module SSD card coin cell battery battery base cover Follow the procedure in After working inside your computer Display bezel...

  • Page 47

    display assembly Using a plastic scribe, pry the edges to release the display bezel from the display assembly [1, 2]. Remove the display bezel from display assembly. Removing and installing components...

  • Page 48

    Installing the display bezel Place the display bezel on the display assembly. Starting from the top corner, press on the display bezel and work around the entire bezel until it clicks on to the display assembly. Install the: display assembly back cover rear cover memory module...

  • Page 49

    Installing the camera Place the camera on the display assembly. Connect the camera cable to the connector on the display assembly. Install the: display bezel display assembly back cover rear cover memory module SSD card battery base cover Follow the procedure in After working inside your computer.

  • Page 50

    base cover battery SSD card memory module rear cover back cover display assembly display bezel To remove the display hinge: Remove the M2.5x2.5L (8) screws that secure the display hinge to the display assembly [1]. b Lift the display hinge away from the display assembly [2]. Installing the display hinge Place the display hinge cover on the display assembly.

  • Page 51

    battery base cover Follow the procedure in After working inside your computer. Display panel Removing the display panel Follow the procedure in Before working inside your computer. Remove the: base cover battery SSD card memory module rear cover back cover display assembly display bezel display hinge...

  • Page 52

    Installing the display panel Connect the eDP cable to the connector. Affix the adhesive tape to secure the eDP cable. Replace the display panel to align with the screw holders on the display assembly. Tighten the M2x2.5L (4) screws to secure the display panel to the display assembly. Install the: display bezel display assembly...

  • Page 53

    back cover display assembly display bezel display hinge display panel Unroute the eDP cable from the routing channel to remove from the display. Installing the eDP cable Place the eDP cable on the display panel. Route the eDP cable through the routing channel. Install the: display panel display bezel...

  • Page 54

    Display back cover assembly Removing the display back cover assembly Follow the procedure in Before working inside your computer. Remove the: base cover battery SSD card memory module rear cover back cover display assembly display bezel display hinge display panel camera eDP cable The display back cover assembly is the remaining component, after removing all the components.

  • Page 55

    back cover rear cover memory module SSD card battery base cover Follow the procedure in After working inside your computer. Removing and installing components...

  • Page 56

    How to check the status of AC Adapter in BIOS? Restart / Power on your computer. At the first text on the screen or when the Dell logo appears, tap <F2> until the message Entering Setup appears. Under General > Battery Information, you will see AC Adapter listed.

  • Page 57

    Support for the Intel® I219LM and Intel® I219V Gigabit Network Connection. Intel® integrated 10/100/1000 MAC NOTE: Not all features mentioned here for the HM175 Express chipset may be available for Dell units, please refer to particular system specification for detail. DDR4 DDR4 (double data rate fourth generation) memory is a higher-speed successor to the DDR2 and DDR3 technologies and allows up to 512 GB in capacity, compared to the DDR3's maximum of 128 GB per DIMM.

  • Page 58

    DDR4 needs 20 percent less or just 1.2 volts, compared to DDR3 which requires 1.5 volts of electrical power to operate. DDR4 also supports a new, deep power-down mode that allows the host device to go into standby without needing to refresh its memory. Deep power-down mode is expected to reduce standby power consumption by 40 to 50 percent.

  • Page 59

    Memory Errors Memory errors on the system display the new ON-FLASH-FLASH or ON-FLASH-ON failure code. If all memory fails, the LCD does not turn on. Troubleshoot for possible memory failure by trying known good memory modules in the memory connectors on the bottom of the system or under the keyboard, as in some portable systems.

  • Page 60

    • An additional physical bus that is added in parallel with the existing USB 2.0 bus (refer to the picture below). • USB 2.0 previously had four wires (power, ground, and a pair for differential data); USB 3.0/USB 3.1 Gen 1 adds four more for two pairs of differential signals (receive and transmit) for a combined total of eight connections in the connectors and cabling.

  • Page 61

    the new protocol, the connector itself remains the same rectangular shape with the four USB 2.0 contacts in the exact same location as before. Five new connections to carry receive and transmitted data independently are present on USB 3.0/USB 3.1 Gen 1 cables and only come into contact when connected to a proper SuperSpeed USB connection.

  • Page 62

    HDMI 1.4 This topic explains the HDMI 1.4 and its features along with the advantages. HDMI (High-Definition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or video monitor, such as a digital TV (DTV).

  • Page 63

    Features • Support for up to three independent displays via HDMI 1.4, DisplayPort (DP) 1.2, an Embedded DisplayPort (eDP) 1.4 interfaces. • Quick Sync Video • Clear Video • Clear Video HD Power Consumption The HD Graphics 630 can be found in several notebook and desktop processors of different TDP classes (35 — 91 W). Key Specifications The following table contains the key specifications of the Intel HD Graphics 630: Table 4.

  • Page 64

    Power Consumption The NVIDIA GeForce GTX 1050 Graphics can be found in several notebook and desktop processors of different TDP classes (40 — 50 W). Key Specifications The following table contains the key specifications of the NVIDIA GeForce GTX 1050: Table 5.

  • Page 65

    Table 6. Key Specifications Specification NVIDIA GeForce GTX 1050 Ti HD Graphics Series NVIDIA GeForce GTX 1050 Ti Codename N17P-G1 Architecture Pascal Pipelines 768 - unified Core Speed * 1493 - 1620 (Boost) MHz Memory Bus Width 7000 MHz Shared Memory Technology 14 nm Features...

  • Page 66

    Specification NVIDIA GeForce GTX 1060 Shared Memory Technology 16 nm Features Multi-Projection, G-SYNC, Vulkan, Multi Monitor DirectX DirectX 12_1 Technology and components...

  • Page 67

    Boot menu Press <F12> when the Dell logo appears to initiate a one-time boot menu with a list of the valid boot devices for the system. Diagnostics and BIOS Setup options are also included in this menu. The devices listed on the boot menu depend on the bootable devices in the system.

  • Page 68

    Keys Navigation Enter Selects a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop‐down list, if applicable. Moves to the next focus area. NOTE: For the standard graphics browser only. Moves to the previous page until you view the main screen.

  • Page 69

    System Configuration screen options Option Description Integrated NIC Allows you to configure the integrated network controller. The options are: • Disabled • Enabled • Enabled w/PXE: This option is enabled by default. SATA Operation Allows you to configure the internal SATA hard-drive controller. The options are: •...

  • Page 70

    Option Description USB PowerShare This field configures the USB PowerShare feature behavior. This option allows you to charge external devices using the stored system battery power through the USB PowerShare port (disabled by default). Audio This field enables or disables the integrated audio controller. By default, the Enable Audio option is selected. The options are: •...

  • Page 71

    Option Description NOTE: Successful password changes take effect immediately. Default setting: Not set Strong Password Allows you to enforce the option to always set strong passwords. Default Setting: Enable Strong Password is not selected. NOTE: If Strong Password is enabled, Admin and System passwords must contain at least one uppercase character, one lowercase character and be at least 8 characters long.

  • Page 72

    Option Description • Disable • Activate (selected by default) NOTE: The Activate and Disable options will permanently activate or disable the feature and no further changes will be allowed CPU XD Support Allows you to enable the Execute Disable mode of the processor. Enable CPU XD Support (default) OROM Keyboard Allows you to set an option to enter the Option ROM Configuration screens using hotkeys during boot.

  • Page 73

    Option Description NOTE: If you disable the Custom Mode, all the changes made are erased and the keys restore to default settings. Intel Software Guard Extensions screen options Option Description Intel SGX Enable This field specifies you to provide a secured environment for running code/storing sensitive information in the context of the main OS.

  • Page 74

    Configuration • Standard — Fully charges your battery at a standard rate. • ExpressCharge — The battery charges over a shorter period of time using Dell’s fast charging technology. This option is enabled by default. • Primarily AC use •...

  • Page 75

    POST Behavior screen options Option Description Adapter Warnings Allows you to enable or disable the system setup (BIOS) warning messages when you use certain power adapters. Default setting: Enable Adapter Warnings Numlock Enable Allows you to enable the Numlock option when the computer boots. Enable Network.

  • Page 76

    Wireless screen options Option Description Wireless Switch Allows to set the wireless devices that can be controlled by the wireless switch. The options are: • WLAN • Bluetooth All the options are enabled by default. Wireless Device Allows you to enable or disable the internal wireless devices. Enable •...

  • Page 77

    If BitLocker is enabled, it must be suspended prior to updating the system BIOS, and then re-enabled after the BIOS update is completed. Restart the computer. Go to Dell.com/support. • Enter the Service Tag or Express Service Code and click Submit.

  • Page 78

    Password type Description Setup password Password that you must enter to access and make changes to the BIOS settings of your computer. CAUTION: The password features provide a basic level of security for the data on your computer. CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended. NOTE: Your computer is shipped with the system and setup password feature is disabled.

  • Page 79

    System specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more information about the configuration of your computer, go to Help and Support in your Windows operating system and select the option to view information about your computer.

  • Page 80

    Memory Feature Specification Type DDR4 SDRAM Speed 2400 MHz Connectors Capacity 4 GB, 8GB, 16 GB Minimum Memory 4 GB ( 1 x 4GB) Maximum memory 32 GB Video Feature Specification Type MXM type-A add-in card Data bus PCIE x16, Gen3 Video controller and •...

  • Page 81

    USB C connector one (optional) with Thunderbolt USB 3.1 with Gen 1 three (with PowerShare) Video HDMI 2.0 Memory card reader SD 4.0 Display Features Specification Type FHD (1920 x 1080) Size 15.6 inches Dimensions: Height 193.59 mm (7.62 inches) Width 344.16 mm (13.54 inches) Diagonal...

  • Page 82

    • 1048/984 cpi Size Sensor-active area: • Width: 99.5 mm (3.92 inches) • Height: 53 mm (2.09 inches) Multi-Touch Configurable single finger and multi-finger gestures Camera Features Specification Type CMOS Sensor Still Resolution 1280 x 720 Pixels (Maximum) Video Resolution 1280 x 720 Pixels (Maximum) Diagonal 74 degrees...

  • Page 83

    • Discharge: 0° C to 70° C (32° F to 122° F) Non-Operating -20° C to 65° C (4° F to 149° F) Coin-cell battery 3 V CR2032 lithium ion cell AC adpter Features Specification Wattage 180 W Input voltage 100 VAC to 240 VAC Input current 3.5 A...

  • Page 84

    Operating 10° C to 35° C (50° F to 95° F) Storage -40° C to 65° C (-40° F to 149° F) Relative humidity (maximum): Storage 20% to 80% (non-condensing) Maximum vibration: Operating 5 to 350 Hz at 0.0002 G²/Hz Storage 5 to 500 Hz at 0.001 to 0.01 G²/Hz Maximum shock:...

  • Page 85

    Device drivers This section provides information about Windows 10 drivers. Drivers can be downloaded from the Dell Support website. Most of the device drivers are pre-installed during the Windows installation process. For best results, Dell recommends installing the chipset driver utility first, followed by the rest of the devices' drivers/software packages in any sequence.

  • Page 86

    Intel chipset drivers Verify if the Intel chipset drivers are already installed in the laptop. Table 10. Intel chipset drivers Before installation After installation Intel management engine interface Verify if the Intel management engine interface drivers are already installed in the laptop. Software...

  • Page 87

    Table 11. Intel management engine interface Before installation After installation Intel Serial Input Output Verify if the Intel Serial I/O driver is already installed in the system, by referring to the illustration below. Software...

  • Page 88

    Table 12. Intel Serial Input Output Before installation After installation Intel dynamic platform and thermal framework drivers Verify if the Intel dynamic platform and thermal framework drivers are already installed in the laptop. Table 13. Intel dynamic platform and thermal framework drivers Before installation After installation Intel software guard extensions...

  • Page 89

    Intel HID event filter Verify if the Intel HID event filter driver are already installed in the laptop. Table 14. Intel HID event filter Before installation After installation Intel HD Graphics Verify if the Intel HD Graphics driver is already installed in the system, by referring to the illustration below. Table 15.

  • Page 90

    Table 17. Bluetooth drivers Before installation After installation Intel Ethernet controller drivers Verify if the Intel ethernet controller drivers are already installed in the laptop. There is no visible change before and after installation Table 18. Intel Ethernet controller drivers Before installation After installation RealTek card reader drivers...

  • Page 91

    Running the ePSA diagnostics Power-on the computer. As the computer boots, press the F12 key as the Dell logo appears. On the boot menu screen, select the Diagnostics option. Click the arrow key at the bottom left corner.

  • Page 92

    Thunderbolt 3 Type-C port does not support certain docking systems features The Vostro 15-7570 system do not support all of the Dell Docking solution features of the Dell Thunderbolt Dock TB16, Dell Dock WD15, Dell Universal Dock D6000, as well as third-party docking solutions features.

  • Page 93

    Third-party docking solutions features • The Vostro 15-7570 system supports standard Thunderbolt 3 protocol/features on external graphic docks. However, performance has not been validated in many third-party Thunderbolt 3 eGfx docks and so users may experience certain unexpected compatibility issues.

Comments to this Manuals

Symbols: 0
Latest comments: