Yale SR-310 User Manual page 19

Changing the Batteries
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte - Door/Window Contact Battery Change
(SE) Batteribyte - (DK) Batteriskift.
When the battery is low the LED will light up when the
door/window is opened.
Note: Door/Window Contact case tamper conditions are also
(22)
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte -
indicated by a lit LED, check the tamper before changing
(SE) Batteribyte - (DK) Batteriskift.
the battery.
To change the battery:
1. Disarm
SR-KP
4. Remove battery
(22)
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte -
(SE) Batteribyte - (DK) Batteriskift.
SR-DC
PIR Battery Change
When the battery is low the LED will flash when any motion is
detected. The batteries are changed as follows:
SR-PC
EF-PIR
SR-KP
1. Disarm 2.
SR-PIR / PETPIR Unscrew
& remove
top case
SR-DC
SR-PC
1. Disarm 2.
SR-PC
Unscrew
& remove
top case
SR-PIR / PETPIR
(22)
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte -
(SE) Batteribyte - (DK) Batteriskift.
CHANGE
BATTERY
CHANGE
BATTERY
SR-KP
CR 2032
CR 2032
CHANGE
BATTERY
3.
2. Unscrew
Remove cap
top case.
CR 2032
SR-DC
CR 2032
CR 2032
5. Replace 6. Refit.
CR 2032
Please ensure battery
2 x 1.5v AA
is inserted correctly.
SR-PC
2 x 1.5v AA
CHANGE
BATTERY
2 x 1.5v AA
3 x 1.5v AAA
CR 2032
3 x 1.5v AAA 3 x 1.5v AAA
Alkaline
SR-PIR / PETPIR
3. 3. CR 2032
Remove Replace
Batteries Batteries
2 x 1.5v AA
Alkaline
3. Remove &
replace Batteries
3 x 1.5v AAA
Please be careful when
removing case as cable
is very delicate.
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte -
(SE) Batteribyte - (DK) Batteriskift.
SR-PVC
1. Disarm
(GB) Changing batteries - (IT) Sostituzione batterie - (DE) Batteriewechsel - (NO) Batteribytte -
SR-PVC
(SE) Batteribyte - (DK) Batteriskift.
Key Fob Battery Change
When the battery is low the LED will glow dimly when any key is
SR-PVC
pressed. The battery is changed as follows:
SR-KF
1.
Disarm
SR-KF
SR-SD
Press any key and check that the LED lights. If the LED lights the
new battery installation is successful.
SR-SD
Ensure tamper spring is fully depressed when re-fitting the PIR
to the back case. If this has not been done correctly this will be
indicated by a flashing LED on the PIR.
SR-PB
SR-PB
4. Refit.
4. Refit.
(cont.)
CHANGE
BATTERY
CR 2032
3 x 1.5v AA
(Lithium)
3.
2.
Unscrew Remove
& remove & replace
top case Batteries
CR 2032
3 x 1.5v AA
(Lithium)
CR 2032
2 x 1.5v AA
2. 3.
Unscrew &
Remove
remove
& replace
battery
3 x 1.5v AA
3 x 1.5v AAA
(23)
4. Refit.
(23)
CR 2032
3 x 1.5v AA
4.
Replace cover
CR 2032
CR 2032
19