Advertisement
RESETTING AIR FILTER COUNTER
To reset the air filter counter when you replace your filter:
1. Rotate dial to AIR FILTER .
2. press and release COPY to reset counter
3. Press and release COPY again to restore previous count.
4. Return the dial to the RUN position.
SETTING THE AIR FILTER LIFE
This value sets the number of days to be counted before a filter
change is indicated.
To set the AIR FILTER USAGE LIMIT:
1. Rotate dial to AIR FILTER.
2. LCD shows: SET LIMIT at lower left, with current setting center
screen.
3. With a new filter installed, use the UP/DOWN keys to change this
value to the number of days of useful filter life specified by your filter
manufacturer.
4. The counter will be reset to zero when usage limit has changed.
5. Return the dial to the RUN position.
TEMPERATURE OVERRIDE
OVERRIDE allows you to change the current SET TEMPERATURE in
HEAT or COOL until the next program period without changing your
temperature control programs.
Press UP/DOWN to change the current temperature setting. The
G
OVERRIDE indicator appears on display.
G
The OVERRIDE will be canceled at the start of the next program period,
and the temperature setting will return to its programmed value.
G
An OVERRIDE may be terminated by rotating the dial, switching the
mode to OFF, or initiating a HOLD.
G
Adjusting the set temperature to its program value will also cancel an
OVERRIDE.
TEMPERATURE HOLD
HOLD may be used for manual temperature control. HOLD is the
simplest means to set and maintain a fixed temperature. It allows you to
set and maintain a fixed temperature indefinitely in Heat or Cool without
concern for programming. To initiate a HOLD:
G
Press and release HOLD.
G
Adjust temperature as desired with UP/DOWN.
G
Temperature setting will not change until the HOLD is cancelled.
G
To cancel a HOLD, press and release HOLD again, rotate the dial, or
switch mode to OFF.
ADVANCED FEATURES
TEMPERATURE SWING
A thermostat works by turning your heating or cooling system on or off
whenever the room temperature varies from the set-point temperature.
This variation is the "swing." Your system should cycle on about 3 to 6
times per hour. A smaller swing number increases the number of cycles,
so room temperature is more constant. A larger swing number decreases
the number of cycles, but saves energy in most cases.
SWING SETTING
1. Rotate dial to the AIR FILTER position.
2. Simultaneously press NEXT & HOLD.
3. Use UP/DOWN keys to change swing.
4. Choices are 1 through 9. The default is 2.
5. Rotate the dial to the RUN position to finish.
TEMPERATURE CALIBRATION
1. Rotate the dial to SET DAY/TIME.
2. Simultaneously press NEXT & HOLD.
3. Use UP/DOWN keys to adjust the thermostats calibration by as
much as ± 5°F (± 3°C).
LOCK
To prevent tampering, press NEXT NEXT
NEXT HOLD. This sequence of keys will lock
and unlock the set temperature, programs
and other settings. When the keys are locked,
a padlock icon will be visible above the time
and temperature display. The Lock will be
disabled after a Hardware Reset.
© COPYRIGHT 2005 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED
M
O
N
ITE
HEAT
1 : 30
70
SET
120
FILTER
SETUP OPTIONS
JUMPER SETTINGS
There are four jumpers, each controls a setting depending on its
position.
GAS/ELECTRIC MODE - J4
The position of this jumper controls when the thermostat requests the
system fan to run. In HEAT mode with the gas jumper in place, the fan is
controlled by the heating system itself. In HEAT mode with the jumper
open or removed, the fan is controlled by the thermostat.
5MIN/2MIN MINIMUM RUN TIME - J3
The position of J3 sets the minimum length of time that the thermostat
must remain with Heat or Cool either on or off before it will automatically
switch to the alternate On or Off state. This feature prevents short cycling
and provides compressor protection for cooling units. Choices are 2 or 5
minutes.
TEMPERATURE DISPLAY FORMAT °F/C - J2
The position of this jumper controls whether temperature is displayed
in degrees F° or C°
TIME DISPLAY FORMAT 12/24 HR CLOCK - J1
The position of this jumper controls whether time is displayed in 12
hour or 24 hour Military Time format.
REPOSITIONING JUMPERS
To change a setting, the jumper must be repositioned and a
HARDWARE RESET must be performed. These jumpers are located
inside the thermostat on the rear of its circuit board. To access them,
remove the unit from the wall by pressing up on the thumb latch at the
bottom of thermostat and swinging the body out and away.
The table pictured on the right is also
printed on the circuit board. The closed or
shorted position is that which covers both a
jumpers pins. To prevent its loss, a jumper
may be placed over one pin only for the
open positions. After settings have been
changed, press S8, the HARDWARE RESET
button for the changes to take effect. See HARDWARE RESET
BATTERIES AND MAINTENANCE
INSTALLING BATTERIES/ MAINTENANCE
The PSP711CC requires batteries to operate your heating/cooling
system. Replace the batteries when the battery REPLACE indicator
appears in the display or at least once a year.
1. Switch electricity to the furnace and air conditioner OFF.
2. To access your units batteries remove the unit from the wall by
pressing up on the thumb latch at the bottom of thermostat and swinging
the body up and away.
3. Remove the used batteries.
4. Install two new Energizer or DURACELL "AA" size alkaline
batteries in the battery compartment. Observe the polarity marking
shown in the compartment.
5. Hang the top of the unit by the tabs at the top corners of the base,
then snap the bottom of the unit into place. Do not use unnecessary
force. If the body does not snap into place easily, remove the body,
re-hang it from the tabs and try again.
6. Turn the power back on to your heating and/or air conditioning
system. If this is the first time you are installing batteries, the thermostat
will display "SUN 12:00 AM".
Within 90 seconds the thermostat will begin to display the room
temperature alternately with the time. To correct the display, see "Setting
the TIME and DAY," after you set the programs.
TECHNICAL ASSISTANCE
If you have any problems installing or using this thermostat, please
reread the instructions carefully or visit our online technical support at
www.luxproproducts.com. Technical assistance is available through our
Technical Service Number. If you require assistance, please call our office
between 8:00 a.m. and 4:30 p.m. Eastern Standard Time, Monday
through Friday. The number is (856) 234-8803.
WARRANTY
Limited Warranty: If this unit fails because of defects in materials or
workmanship within one year of date of original purchase, LUX will, at its
option, repair or replace it. This warranty does not cover damage by
accident, misuse, or failure to follow installation instructions. Implied
warranties are limited in duration to one year from date of original
purchase. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you. Please return
malfunctioning or defective units to the participating retailer from which
the purchase was made along with proof of purchase. Please refer to
"Technical Assistance" before returning your thermostat. Purchaser
assumes all risks and liability for incidental and consequential damage
resulting from installation and use of this unit. Some states do not allow
the exclusion of incidental or consequential damages, so the above
exclusion may not apply to you. This warranty gives you specific legal
rights and you may also have other rights which vary from state to state.
Applicable in the U.S.A. only.
OPEN CLOSE
J4
ELECT
GAS
J3
2MIN
5MIN
J2
C
F
J1
24HR
12HR
4
Advertisement
