Lux Products LUXPRO PSP711CC series Installation And Operating Instructions

Complete, Easy To Read
INSTALLATION AND OPERATING
INSTRUCTIONS
PSP711CC SERIES
SMART TEMP ELECTRONIC THERMOSTAT
PM
SET
SUNDAY
WEEKDAY
PROGRAM
SET
DAY/TIME
Installs Easily Set Day and Time
LUX PRODUCTS CORPORATION
Mt. Laurel, New Jersey 08054, USA
WARNING: Use Energizer ® or DURACELL
Energizer ® is a registered trademark of Eveready Battery Company, Inc.
DURACELL ® is a registered trademark of The Gillette Company, Inc.
I M P O R T A N T !
Please read all instructions carefully before beginning
installation. Save them for future reference. Before removing
any wiring from your existing thermostat, its wires must be
labeled with their terminal designations. Ignore the color of the
wires since they may not comply with any standard.
Thank you for your confidence in our product. To obtain the best
results from your investment, please read these instructions and acquaint
yourself with your purchase before installing your new thermostat. Then
follow the installation procedures, one step at a time. This will save you
time and minimize the chance of damaging the thermostat and the
systems it controls. These instructions may contain information beyond
that required for your particular installation. Please save for future
reference.
COMPATIBILITY
The PSP711CC can be used with most single stage 24 volt gas, oil or
electric heating and air conditioning systems, single stage heat pumps, or
gas millivolt heating systems. It cannot be used with 3 wire zone valves,
120 volt heating systems, or multi stage heat pumps. Ask your dealer for
other LUX thermostats to control those systems.
FEATURES
LARGE
BACKLIT
DISPLAY
EASY
PROGRAMMING
WITH
LUX SPEED DIAL ®
Small elegant design
G G
Exclusive LUX Speed Dial
G ® G
G EL Illuminated Display G
G Comprehensive Graphical G
Filter Monitor
G
7 Day Programming
G
Energy Star Compliant
G G
4 Periods Per Day
G
Independent Fan Program G
G
Programmable (minimum)
G
Fan Duty Cycle
Nonvolatile Memory For
G
All Programs And Settings
G Temporary Temperature
Override
C A U T I O N
The PSP711CC is protected against normal static electric discharges.
To minimize the risk of damaging the unit in extremely dry weather,
touch a grounded metal object before touching your thermostat.
© COPYRIGHT 2005 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED
Easy as
HEAT
OFF
COOL
1–2–3
Choose Heat or Cool
43376
® Alkaline Batteries Only.
UP
DOWN
LIGHT
IAQ
INDEPENDENTLY
PROGRAMMABLE
FAN
MODE SWITCH
Temperature Hold
Keyboard Lockout
F/C Temperature Display
12/24 Hr Clock Display
Adjustable Temperature
Differential / Cycle Rate
User Temperature Offset /
Calibration
5/2 minute selectable
minimum Run/Off time provides
short cycle and compressor
protection
INSTALLATION
Please read all instructions carefully before beginning installation.
C A U T I O N
Turn off electricity to the appliance before installing or
OFF
servicing thermostat or any part of the system. Do not
turn electricity back on until work is completed.
Do not short (jumper) across electric terminals on furnace or air
G
conditioner to test the system. This may damage the thermostat and
void your warranty.
G All wiring must conform to local codes and ordinances.
G The thermostat should be limited to a maximum of 1.5 amps;
higher current may cause damage to the thermostat.
G Your thermostat is a precision instrument. Please handle it with
care.
TOOLS REQUIRED
G #1 Phillips screwdriver (small)
G Drill with 3/16-in. (4.8mm) bit
G Wire stripper/cutter
THERMOSTAT LOCATION
On replacement installations, mount the new thermostat in place of the
old one unless the conditions listed below suggest otherwise. On new
installations, follow the guidelines listed below.
1. Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the
floor, and in a room that is used often.
2. Do not install it where there are unusual heating conditions, such as:
in direct sunlight; near a lamp, television, radiator, register, or fireplace;
near hot water pipes in a wall; near a stove on the other side of a wall.
3. Do not locate in unusual cooling conditions, such as: on a wall
separating an unheated room; or in a draft from a stairwell, door, or
window.
4. Do not locate in a damp area. This can lead to corrosion that may
shorten thermostat life.
5. Do not locate where air circulation is poor, such as: in a corner or an
alcove; or behind an open door.
6. Do not install the unit until all construction work and painting has
been completed.
C A U T I O N
G Read instructions carefully before removing any wiring from existing
thermostat.
Wires must be labeled before they are removed.
G
Do not allow wires to touch each other or parts on thermostat.
G
G When removing wires from their terminals, ignore the color of the
wires since they may not comply with any standard.
REMOVING THE OLD THERMOSTAT
1. Switch electricity to the furnace and air conditioner
OFF; then proceed with the following steps.
2. Remove cover from old thermostat. Most are snap-
on types and simply pull off. Some have locking
screws on the side. These must be loosened.
3. Note the letters printed near the terminals. Attach
labels (enclosed) to each wire for identification.
Remove and label wires one at a time. Make sure the wires do not fall
back inside the wall.
4. Loosen all screws on the old thermostat and remove it from the wall.
MOUNTING THE PSP711CC
1. Strip insulation leaving 3/8 in.
(9.5mm) bare wire ends and clean off
any corrosion.
2. Fill wall opening with non-
combustible insulation to prevent drafts
from affecting the thermostat.
C A U T I O N
Be careful not to drop the unit or disturb electronic parts.
Leave the door closed while the body is being removed
from the base.
3. Remove the body from the thermostat's base by pressing the thumb
latch at the bottom center of the unit and swinging the body away.
N O T E
If you are mounting the base to soft material like plasterboard or if you
are using the old mounting holes, the screws may not hold. Drill a 3/16
in. (4.8mm) hole at each screw, and insert the plastic anchors provided.
1