Agilent Technologies InfiniiVision 3000 Programmer's Manual page 1226

Index
RCL (Recall), 167
Rds (dynamic ON resistance) waveform,
Rds(on) value for conduction calculation,
reactive power, 462, 539
read configuration, 163
ReadIEEEBlock method, 59, 63, 65
ReadList method, 59, 63
ReadNumber method, 59, 63
readout, 1019
ReadString method, 59, 63
real (actual) power, 539
real power, 463
real-time acquisition mode, 223
recall, 167, 566, 828
recall arbitrary waveform, 567
RECall commands, 565
recall filename, 568, 969
recall mask, 569
recall path information, 570
recall reference waveform, 572
recall setup, 571
recalling and saving data, 290
receiver width, I2S, 659
RECTangular window for transient signals,
reference, 311, 836
reference for time base, 1043
reference waveform save source,
reference waveform, recall, 572
reference waveform, save, 594
reference waveforms, clear, 987
reference waveforms, display, 988
reference waveforms, label, 989
reference waveforms, save to, 990
reference waveforms, skew, 991
reference waveforms, Y offset, 992
reference waveforms, Y range, 993
reference waveforms, Y scale, 994
reference, lister, 362
registers, 160, 167, 171, 184, 193, 195, 197,
199, 201, 203, 205, 208, 210
registers, clearing, 1074
reject filter, 869
reject high frequency, 847
reject noise, 852
relative standard deviation, 428
remote control examples, 1097
Remote Terminal Address (RTA), M1553
trigger, 702
remove cursor information, 365
remove labels, 297
remove message from display, 820
reorder channels, 185
repetitive acquisitions, 211
report errors, 821
report transition, 429, 431
reporting status, 1055
reporting the setup, 844
request service, 175
Request-for-OPC flag clear, 157
reset, 168
reset conditions, 168
reset defauts, waveform generator,
1226
reset mask statistics,
554 reset measurements,
556 resolution of printed copy,
resource session object,
ResourceManager object,
restore configurations, 163, 167, 171,
restore labels,
restore setup,
return values, query,
returning acquisition type,
returning number of data points,
RF burst demo signal,
right reference,
ringing pulse demo signal,
ripple (output) analysis,
ripple, output,
rise time measurement,
rise time of positive edge,
Rise Time, power modulation analysis,
rising edge count measurement,
rising pulse count measurement,
RMS - AC, power modulation analysis,
RMS value measurement,
321 roll time base mode,
root (:) commands, 179,
root level commands,
593 RQL (Request Control) status bit, 158,
RQS (Request Service),
RS-232/UART triggering,
RST (Reset), 168
rules, tree traversal,
rules, truncation,
run, 176, 211
Run bit, 199, 201
run count, current harmonics analysis,
run mode, mask test,
running configuration, 171,
RUNT SEARch commands,
runt search polarity,
runt search qualifier,
runt search source,
runt search, pulse time,
RUNT trigger commands,
runt trigger polarity,
runt trigger qualifier,
runt trigger source,
runt trigger time,
Rx frame count (UART),
Rx source, 734
S
sample rate, 230
sampled data,
sampled data points,
SAV (Save), 171
save, 171, 575
save arbitrary waveform,
SAVE commands,
save current harmonics analysis results,
save filename,
980
save image, 578
Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
479
295
1014
59
59
828
297
167
1095
231
224
275
836
274
540
464
388
418
529
409
412
529
440
833
182
3
160
175
596
1093
1090
520
486
828
758
759
760
761
762
892
893
894
895
896
729
1006
933
576
573
585
577
save image with inksaver, 581
save mask, 583, 584
save mask test failures, 489
save path information, 586
save reference waveform, 594
save setup, 587
save to reference waveform location,
save waveform data, 588
saved image, area, 1041
saving and recalling data, 290
SBUS A429 commands, 600
SBUS CAN commands, 618
SBUS commands, 595
SBUS I2S commands, 654
SBUS<n> commands, general, 597
scale, 335, 837, 841
scale factors output on hardcopy, 345,
scale for channels, 270
scale units for channels, 271
scale units for external trigger, 305
scaling display factors, 263
SCPI commands, 67
SCPI.NET example in C#, 1198
SCPI.NET example in IronPython,
SCPI.NET example in Visual Basic .NET,
SCPI.NET examples, 1198
scratch measurements, 1018
screen area for hardcopy print, 343
screen area for saved image, 1041
screen image data, 296
SDI pattern, ARINC 429 trigger, 613,
SEARch commands, 743
SEARch commands, A429, 768
SEARch commands, CAN, 774
SEARch commands, EDGE, 748
SEARch commands, FLEXray, 780
SEARch commands, general, 744
SEARch commands, GLITch, 751
SEARch commands, I2S, 786
SEARch commands, IIC, 792
SEARch commands, LIN, 799
SEARch commands, M1553, 805
SEARch commands, RUNT, 758
SEARch commands, SPI, 809
SEARch commands, TRANsition,
SEARch commands, UART, 813
search mode, 746
search state, 747
search, edge slope, 749
search, edge source, 750
SECAM, 909, 913
seconds per division, 837
segmented waveform save option,
segments, analyze, 225
segments, count of waveform, 943
segments, setting number of memory,
segments, setting the index, 227
segments, time tag, 944
select measurement channel, 421
self-test, 177
sensing a channel probe, 1005
sensing a external trigger probe,
990
579
1210
1204
772
763
592
226
1009