Operating The Fire; Manual Controls - Valor ALTON DIMENSION Manual

Method C (Fig. 5 & Fig. 6)
Note: The optional spacer frame enables the appliance to be fixed against a flat wall. For your safety, the frame and the
appliance must be securely fixed to the wall/surround.
Fitting the spacer Frame to the Wall/Surround
Identify the rear of the spacer frame which has two fixing slots on the top rear flange. Position the rear of the spacer
frame flat against the wall. Ensure that the spacer is central to the fireplace and that the legs are positioned correctly and
are upright. Mark the upper position of the fixing slots on the wall (Fig 5). Remove the spacer frame and drill a hole on the
marked locations using a suitable sized masonry drill bit for the supplied wall plugs. Insert two wall plugs into the holes,
then screw in two wood screws in to the wall plugs until approximately 6mm of screw is left protruding from the wall.
Fitting the Spacer Frame to the Appliance
The spacer frame is secured to the appliance in four positions (Fig. 6). Secure the spacer frame to the appliance using
the four No.8 x 3/8 screws supplied.
Fitting the Appliance with Spacer Frame
Carefully lift the appliance and locate the slots on the rear of the spacer frame onto the screws in the wall. The screws
can be adjusted to ensure a tight fit. When mounting to decorative surfaces such as wallpaper, care must be taken not
to drag the appliance down the wall as it may damage the decorative surface.
Fitting the Decorative Fascia to the Appliance (Fig. 7 - Fig. 10)
Fitting the Fascia Frame
Remove the fascia frame from its packaging. Attach the four large fascia frame magnets to the side flanges of the
appliance in the approximate locations shown in Fig. 8. Line up the fascia frame with the appliance and ensure the
magnets are positioned correctly so that they fit inside the fascia frame. Push the fascia frame onto the appliance until
the magnets lock the fascia frame in place.
Fitting the Fascia Trims
Carefully remove the fascia trims from their packaging, taking care not to scratch their outer surfaces and taking care
of any burrs that may be present on the edge of the trims. Attach the six small trim magnets to the fascia frame in the
approximate locations shown in Fig. 9. Attach the two side fascia trims on to the outer edges of the fascia frame, then
attach the top fascia trim. The trim magnets may have to be repositioned so that the trims sit flat on the fascia frame.
Fitting the Plastic Infill Trim (Alton, Bauhaus, Clifton & Downton models only)
Remove the plastic infill trim from its packaging. Locate the four tabs on the rear of the plastic infill trim into the four
corresponding slots on the front of the appliance. Push the infill trim downwards so that the tabs lock in place (Fig. 10)
Fitting the Fret and Ash Pan
Remove the fret, ash pan and metal infill from their packaging.
For the Blenheim model, locate the metal infill on the back of the fret as per the instruction leaflet in the fret packaging.
For the Alton, Bauhaus, Clifton and Downton models, the metal infill can be disgarded.
For the Bauhaus model, fit the two finials on top of the fret as per the instruciton leaflet in the fret packaging.
Centre the fret in front of the appliance. Position the ash pan beneath the fret.

Operating the Fire

MANUAL CONTROLS

The manual controls are located at the base of the appliance. Remove the ash pan to access the controls (Fig 11a).The
main switch controls the electricity supply to the appliance.The switch can be pressed on either side. Please see the
table below for the functions that correspond to the switching sequence.
Switch Operation
Press Once
Press
Press
Press
Press Once
Two Red LED's as shown in Fig. 11b are located behind the flame panel and indicate the heat setting of the appliance.
These LED's illuminate when a heat setting is selected and remain illuminated for aproximatly 3 seconds.
- One illuminated LED corresponds to Half Heat (650 Watts).
- Two illuminated LED's correspond to Full Heat (1300 Watts).
LED Hologram Effect On
LED Hologram & Flame Effect On
Once
Flame Effect & Half Heat On
Again
Flame Effect & Full Heat On
Again
Setting
Fire is turned off
Visual Indication
Flame panel illuminated
Flame movement within flame panel
1 Red LED behind flame panel
2 Red LED's behind flame panel
Flame panel becomes darkened