Features • Ventilation: install the unit in a well-ventilated place, otherwise the humidification or vapor may damage SSC-SD26P/36P is a color video camera, equipped with internal parts. a 1/4 type CCD, zoom lens and quick 360° scanning • Power: please observe the labeled specifications on the function.
90% effective image. can it be used for any other special purposes. Sony • Install the unit away from interference sources and Corporation shall not be liable for any incidental,...
Main/Accessory • Camera unit (1) • Operating Instructions Chinese version (1) English version (1) • Sun shield (optional) • 9 pin connecting cable (1) • 3 pin connecting cable (1) • Screw spanner (1) • Allen Wrench (1) • Small plastic bag (2) •...
Component Diagram Connections and setup Alarm In 1 Alarm In 2 Alarm In 3 Alarm In 4 Alarm In 5 Alarm In 6 Monitor Alarm inputs Alarm Alarm Out Open outputs Alarm Out Com Alarm Out Close RS485 AC 24V power adapter Adapter (not supplied) Keypad controller (not supplied)
Operation Instructions Scan function Startup screen: the startup screen will show the software Auto Scan version, communication protocol, machine address, and transmission baud rate, etc. Auto scan can be configured to run at startup, or can be controlled by the keypad controller (for details, see the table on Page 26).
When the scan range has been set When the scan range has been set The camera will scan at 45° increments within the scan The camera will randomly pick a stop point and perform range until a command from the keypad controller is scanning in the set range until a command from the received (e.g., horizontal rotate, vertical rotate, iris, keypad controller is receivied (e.g., horizontal rotate,...
Move the cursor to <MODE>, and then press the Camera Settings OPEN key to enter the mode selection menu. Move the joystick up and down to choose the function to use. FOCUS Press the OPEN key to confirm, or press CLOSE Main menu →...
• In FULL AUTO mode, the shutter speed is fixed at • Zoom levels: 26×, 52×, 104×, 208× and 312× 1/50 sec (PAL), and the camera will automatically (SSC-SD26P), adjust the aperture according to the amount of outside maximum optical zooming: 26×, 52× to 312× is light.
Press the OPEN key to confirm, or press CLOSE Move the cursor to <CAMERA SETUP>, and then to cancel selection and exit from the menu screen. press the OPEN key to enter the <CAMERA SETUP> menu. ZOOM SPEED Move the cursor to SHARPNESS, and then press the OPEN key to enter sharpness selection.
Press the OPEN to key to confirm the zone size, PRIVACY ZONE and then go to the setup screen for the zone color: This feature can enable the user to black out (or white Screen display: PRIVACY ZONE COLOR out) a specifi c portion of the screen to protect the Move the joystick up/down to select the zone color necessary privacy.
Set Alarm Horizontal Pan/Vertical Press “95,” and then hold the PRESET key for Tilt Setup 2 seconds to enter the main menu screen. Main menu → <PAN/TILT SETUP> menu Move the cursor to <CAMERA SETUP>, and then press the OPEN key to enter the <CAMERA SETUP>...
Move the joystick up/down to choose ON or OFF. Move the joystick up/down to choose the desired zoom speed. Press the OPEN key to confirm, or press CLOSE Press the OPEN key to confirm, or press CLOSE to cancel selection and exit from the menu screen. to cancel selection and exit from the menu screen.
Set the Stop Time RECOVER TIME In scan mode (auto, frame, random), if tour and Enter “95,” and then hold the PRESET key for recording tour are interrupted by inadvertent keypad 2 seconds to enter the main menu screen. controller input, the camera will resume the previous action after a set amount of time.
TOUR5 CAMERA TITLE Press “80” and the PRESET key to run TOUR 5. TOUR6 Main menu → <CAMERA TITLE> menu Press “81” and the PRESET key to run TOUR 6. TOUR7 Press “82” and the PRESET key to run TOUR 7. <...
Move the joystick up/down to choose the desired PRESET SETUP preset point, and move left/right to set the preset speed. Main menu → <PRESET SETUP> menu Press the OPEN key to confirm, or press CLOSE to cancel selection and exit from the menu screen. <...
Move the joystick up/down to choose the desired Other menus preset point, and move left/right to set OFF, BLC or WDR. Press the OPEN key to confirm, or press CLOSE FREEZE ACTIVITY to cancel selection and exit from the menu screen. When the camera is in frame, random, auto, or preset scanning modes, the camera screen can be disabled PRESET MOTION...
Press the OPEN key to confirm, or press CLOSE Press the OPEN key to confirm, or press CLOSE to cancel selection and exit from the menu screen. to cancel selection and exit from the menu screen. SCHEDULE MOTION DETECTION Main menu → <OTHERS> menu Main menu →...
Press the OPEN key to confirm, or press CLOSE SYSTEM to cancel selection and exit from the menu screen. PASSWORD WEEK Main menu → <SYSTEM> menu Main menu → <SYSTEM> menu W E E K Mon. < C A M E R A S E T U P > T I M E 1 5 : 1 5 : 1 5 Mon.
TOUR: The camera will run TOUR 1. E-FLIP DEFAULT: The camera will move to the factory set position. Set as E-Flip Main menu → <SYSTEM> menu Press “95,” and then hold the PRESET key for W E E K Mon. <...
Press the OPEN key to confirm, or press CLOSE RECORDING TOUR to cancel selection and exit from the menu screen. This camera provides 4 sets of patterns and playback ACTION modes to select from. Actions for playback include lens zoom, horizontal pan, and vertical tilt, etc. Once the It can be set to resume the previous action (AUTO pattern is recorded, it can be played back accordingly to RETURN) or return to the preset point 1 (PARK) when...
Menu Index Menu Structure <CAMERA SETUP> <Main Menu> <FOCUS> <FOCUS> < C A M E R A S E T U P > MODE AUTO <AE> < P A N / T I L T S E T U P > ACTIVE TIME ----- x 2 6...
Page 25
Main menu Submenu 1 Submenu 2 Contents Factory default CAMERA TITLE CAMERA TITLE 20 CHARACTERS (MAX) INPUT CAMERA TITLE UP/DOWN POSITION CAMERA TITLE ON/OFF PRESET SETUP TOUR P0 ~ 255: ON/OFF PRESET SPEED P0 ~ 255: 30°/sec ~ MAX TITLE PRESET TITLE 20 CHARACTERS (MAX) INPUT...
Preset Commands Preset Commands Use the keypad controller preset commands to quickly execute specific functions or perform setting changes. Refer to the following table for button combinations and corresponding functions. The following commands are for using with keypad controllers Pelco-D or Pelco-P. Shortcut key Function &...
Page 27
Shortcut key Function & Action 97+ Preset Start random scanning 98+ Preset Start frame scanning 99+ Preset Acivate auto scanning 101+ Preset Run Recording Tour - Group 1, repeatable 102+ Preset Run Recording Tour - Group 2, repeatable 103+ Preset Run Recording Tour - Group 3, repeatable 104+ Preset Run Recording Tour - Group 4, repeatable...
Adjust the DIP switch Mount method Use the supplied screw spanner to loosen the 3 screws, and turn the cover in the clockwise direction, then remove the cover. Install the camera Before installation After deciding the installation position of the camera, select the appropriate installation method according to the size of the fixture (not supplied).
Page 29
Install the camera If the camera is installed in the high position, perform regular checks (at least once a year) to ensure no loose connections. If at all possible perform checks more Slide the fixture (not supplied) onto the adapter ring frequently.
Specifications Specifications Model SSC-SD26P SSC-SD36P CCD module FCB-CX990DP FCB-CX1010P name Image device 1/4 type with Exwave HAD CCD Electric shutter 1/1 sec ~ 1/10000 sec Gain control Auto/Manual (–3 ~ +28dB) Exposure control FULL AUTO/SHUTTER PRIORITY/IRIS PRIORITY/MANUAL ATW/AUTO/ONE PUSH/INDOOR/OUTDOOR/MANUAL FOCUS...
Page 36
120W Note Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.
Compatible communication protocol table Protocal type Pelco D/P Protocal type Pelco D/P Joystick Query Tilt Position Zoom Query Zoom Position Iris Set Pattern Start Focus Set Pattern Stop Preset Set Run Pattern Preset Go Backlight ON/OFF Filp (Preset go 33) Set PTZ Position Pan Zero (Preset go 34) Zoom Speed...