Table of Contents
Advertisement
Quick Links
1800 Courtney Park Drive East,
Unit 5-7, Mississauga, Ontario L5T 1W1
For further operating, installation, or maintenance assistance:
PRINTED IN U.S.A.
2434 0497SR
"HL" and "SL" Series
Installation/Operation/Parts
Call 1-800-363-PUMP (7867)
OWNER'S MANUAL
Convertible Deep Well Jet Pumps
6 0
4 0
8 0
2 0
0
1 0
BE423 (Rev. 3/18/98)
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Berkeley HL series
Summary of Contents for Berkeley HL series
- Page 1 OWNER’S MANUAL Convertible Deep Well Jet Pumps 1800 Courtney Park Drive East, Unit 5-7, Mississauga, Ontario L5T 1W1 2434 0497SR “HL” and “SL” Series Installation/Operation/Parts For further operating, installation, or maintenance assistance: Call 1-800-363-PUMP (7867) BE423 (Rev. 3/18/98) PRINTED IN U.S.A.
-
Page 2: General Safety
Safety READ AND FOLLOW ELECTRICAL SAFETY SAFETY INSTRUCTIONS! Capacitor voltage may be hazardous. To discharge motor capacitor, hold insulated handle screw- This is the safety alert symbol. When you see this driver BY THE HANDLE and short capacitor terminals symbol on your pump or in this manual, look for together. -
Page 3: Table Of Contents
Requests for service under this warranty shall be made by contacting ranty lasts, so the above limitations or exclusions may not apply to the installing Berkeley/Wicor dealer as soon as possible after the dis- you.This warranty gives you specific legal rights and you may also have covery of any alleged defect. -
Page 4: Typical Installations
Typical Installations Piping omitted Discharge for clarity "Double Pipe" "Single Pipe" (4" and Larger (2" and 3" Suction over Diameter Well) Diameter Well) Drive Suction (Larger) Pipe f rom Well Drive To Household (Smaller) Air Volume Water System Pipe to Control Well Drive Pipe... -
Page 5: Discharge Pipe And Pressure Tank Connections
Discharge Pipe and Pressure Tank Connections To Household PRE-CHARGE TANK CONNECTION (Figure 6) Water System If your system uses a pre-charged tank, it should be connected to the pump as shown in Figure 6. The relief valve must be capable of passing the entire Relief Valve pump capacity at 100 PSI pressure. -
Page 6: Electrical
Electrical Disconnect power before working on pump, motor, pressure switch, or wiring. Your Motor Terminal Board (under the motor end cover) wiring if line voltage is 230 Volts or if you have a single and Pressure Switch look like one of those shown below. voltage motor. -
Page 7: Preparing To Start The Pump - Deep Well
Preparing to Start the Pump – Deep Well Never run pump against closed discharge. To do so can boil Open control valve as far as possible water inside pump, causing hazardous pressure in unit, risk of explosion and fill pump and and possibly scalding persons handling pump. -
Page 8: Preparing To Start The Pump - Shallow Well
Preparing to Start the Pump – Shallow Well Never run pump against closed discharge. To do so can boil Open control valve water inside pump, causing hazardous pressure in unit, risk of explosion as far as possible and possibly scalding persons handling pump. and fill pump and piping through priming port... -
Page 9: Repair Parts
Repair Parts Repair Parts – “HL” Series Cast Iron Jet Pumps Part 10HL Description Qty. 1/2 HP 3/4 HP 1 HP Motor A100CHL A100DHL A100EHL #§2 Water Slinger C69-2 C69-2 C69-2 Seal Plate N3-9 L3-10 L3-10 #§4 Seal Plate Gasket N20-35 C20-21 C20-21... -
Page 10: Troubleshooting
Troubleshooting Troubleshooting Symptoms Things to Do: A. Motor will not run. A. Check that the disconnect switch is ON and that the circuit breaker has not tripped or the fuse has not blown. DISCONNECT POWER and make sure that wires connecting motor to power supply and pressure switch are tight and correctly connected (see Page 6).
Need help?
Do you have a question about the HL series and is the answer not in the manual?
Questions and answers