Philips 227E3QPHSU/27 Service Manual

21.5 inch w lcd color monitor
Hide thumbs Also See for 227E3QPHSU/27:
Table of Contents

Advertisement

21.5 W LCD Color Monitor
Service
Service
Service
Description
Table of Contents......................................................1
Revision List.............................................................2
Important Safety Notice............................................3
1. Monitor Specifications............................................5
2. LCD Monitor Description........................................7
3. Operation Instructions............................................8
3.1 General Instructions.....................................8
3.2 Control Buttons..........................................8
3.3 OSD Menu......................................................9
4. Input/output Specification..................................10
4.1 Input Signal Connector.......................................10
4.2 Resolution & Preset Modes.................................11
4.3 Pixel Defect Policy.......................................12
4.4 Failure Mode of Panel...................................14
5. Block Diagram...............................................15
5.1 Scaler Board.....................................................15
5.2 Power Board.......................................................16
6. Schematic Diagram.............................................. 17
6.1 Scaler Board..............................................17
6.2 Power Board.......................................................23
6.3 Headphone Board.....................................25
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN
SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Copyright 2011 Philips Consumer Lifestyle
227E3QPHSU/00
227E3QPHSU/01
227E3QPHSU/27
227E3QPHSU/69
227E3QPHSU/93
227E3QPHSU/94
Page
Description
6.4 IR Board.................................................26
6.5 Key Board.................................................28
6.6 LED Board.................................................29
7. PCB Layout................................................30
7.1 Scaler Board............................................30
7.2 Power Board.............................................31
7.3 Headphone Board.....................................33
7.4 IR Board....................................................33
7.5 Key Board.................................................34
7.6 LED Board.................................................34
8. Wiring Diagram.............................................35
9. Scaler Board Overview..................................36
10. Mechanical Instructions...............................37
11. Repair Flow Chart........................................39
12. ISP Instructions..................................................43
13. DDC Instructions................................................50
15. Monitor Exploded View.......................................65
17. Different Parts List......................................76
18. General Product Specification.........................78
SAFETY NOTICE
Subject to modification
K
Jul.12, 2011
Chassis: Meridian 3
Page

Advertisement

Table of Contents
loading

Summary of Contents for Philips 227E3QPHSU/27

  • Page 1: Table Of Contents

    CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES Copyright 2011 Philips Consumer Lifestyle Subject to modification Jul.12, 2011...
  • Page 2: Revision List

    Meridian 3 Revision List Version Release Date Revision History Jul.12, 2011 Initial release, Draft Version Jul.28,2011 Update BOM for 227E3QPHSU/00 and 227E3QPHSU/69 Oct.17,2011 Add CTN model 227E3QPHSU/27 Feb.11,2012 Add CTN model 227E3QPHSU/01...
  • Page 3: Important Safety Notice

    Meridian 3 Important Safety Notice This electronic user guide is intended for anyone who uses the Philips monitor. Take time to read this user manual before you use your monitor. It contains important information and notes regarding operating your monitor. The...
  • Page 4 Meridian 3 IMPORTANT: Always activate a moving screen saver program when you leave your monitor unattended. Always activate a periodic screen refresh application if your monitor will display unchanging static content. Uninterrupted display of still or static images over an extended period may cause “burn in”, also known as “after-imaging”...
  • Page 5: Monitor Specifications

    Meridian 3 1. Monitor Specifications Technical specifications Picture/Display LCD Panel Type TFT-LCD Backlight Panel Size 21.5" W (54.6 cm) Aspect Ratio 16:9 Pixel Pitch 0.248 x 0.248 mm Brightness 250 cd/m² SmartContrast 20,000,000:1 Contrast Ratio (typ.) 1000:1 Response Time (typ.) 5 ms Optimum Resolution 1920 x 1080 @ 60Hz...
  • Page 6 Black (Black) / Blue (Front) Finish Glossy Note: 1. EPEAT Gold or Silver is valid only where Philips registers the product. Please visit www.epeat.net registration status in your country. 2. This data is subject to change without notice. Go to www.philips.com/support...
  • Page 7: Lcd Monitor Description

    Meridian 3 2. LCD Monitor Description The LCD monitor will contain a scaler board, a power board, a headphone board, two IR boards, a LED board and a key board. The scaler board houses the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC inverter voltage to drive the backlight of panel and the scaler board chips each voltage.
  • Page 8: Operation Instructions

    Meridian 3 3. Operating Instructions Connecting to your PC 3.1 General Instructions Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor. By changing these setting, the picture can be adjusted to your personal preference.
  • Page 9: Osd Menu

    3.3 OSD Menu On-screen Display (OSD) is feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly...
  • Page 10: Input/Output Specification

    Meridian 3 4. Input/ Output Specification 4.1 Input Signal Connector T.M.D.S. data0+ T.M.D.S. data0 shield D-sub Connector No Connect Pin No. Signal Name No Connect T.M.D.S clock shield Green/ SOG T.M.D.S. clock+ Blue T.M.D.S. clock- Sense (GND) Cable Detect (GND) Red GND Green GND Blue GND...
  • Page 11: Resolution & Preset Modes

    Meridian 3 4.2 Resolution & Preset Modes Power Management Definition Power Management Definition Maximum Resolution VESA Power 1920 x 1080 at 60 Hz (analog input) Video Mode Used Color 1920 x 1080 at 60 Hz (digital input) < 35 W Active White Recommended Resolution...
  • Page 12: Pixel Defect Policy

    No manufacturer can guarantee that the monitor displays a dark pattern. There are three panels will be free from pixel defects, but Philips types of bright dot defects: guarantees that any monitor with an unacceptable...
  • Page 13 In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.
  • Page 14: Failure Mode Of Panel

    Meridian 3 4.4 Failure Mode Of Panel Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical Polarizer has bubbles instruction on this manual to eliminate failure by replace LCD panel.
  • Page 19 D405 RLZ5.6B C429 NC/100N16V D404 RLZ5.6B C428 NC/100N16V D403 RLZ5.6B C427 NC/100N16V C426 100N16V C425 100N16V C432 NC/0.1UF50V D406 NC/RLZ5.6B...
  • Page 21 R617 NC/750R 1/10W 5% OUTR R616 NC/0R05 1/16W SE-1 R615 NC/750R 1/10W 5% OUTL R614 NC/0R05 1/10W R613 NC/0R05 1/10W...
  • Page 30: Pcb Layout

    Meridian 3 7. PCB Layout 7.1 Scaler Board 715G4641M01000004K Remark: Parts position can be searched by using FIND function in PDF. CN411 CN701 CN408 CN410 R605 C437 C709 C705 CN409 R470 C701 C702 U704 R702 R710 R752 R717 Q702 U703 C435 R705 R721...
  • Page 31: Power Board

    Meridian 3 7.2 Power Board Power 715G4750P02000001S Remark: Parts position can be searched by using FIND function in PDF. GND1 CN902 BD901 J905 C801 CN801 D902 D904 J801 R932 D901 L801 Q903 R935 Q901 ZD902 L901 C908 C927 FB801 F902 R919 R903 J904...
  • Page 32 Meridian 3 Converter 715G4711P0B0020040 Remark: Parts position can be searched by using FIND function in PDF. R814 C813 CN802 C801 R825 IC801 Q801 F801 L801 C810 CN801 ZD801 CN804 CN803...
  • Page 33: Headphone Board

    Meridian 3 7.3 Headphone Board 715G4909T01000004S Remark: Parts position can be searched by using FIND function in PDF. CN006 CN007 7.4 IR Board 715G4595R01000001S Remark: Parts position can be searched by using FIND function in PDF. U053 CN053 R065 C059 715G4813T01000004S Remark: Parts position can be searched by using FIND function in PDF.
  • Page 34: Key Board

    Meridian 3 7.5 Key Board 715G4799K01000004F Remark: Parts position can be searched by using FIND function in PDF. R005 ZD002 CN001 U001 R001 R002 R003 ZD004 7.6 LED Board 715G4864T01000004F Remark: Parts position can be searched by using FIND function in PDF. LED001 CN002...
  • Page 35: Wiring Diagram

    CN804...
  • Page 37: Mechanical Instructions

    Meridian 3 10. Mechanical Instructions Note: Take the 227E3LPH for example (the way of 227E3QPH disassembly is almost the same as 227E3LPH) Step 2: Remove the rear cover 1. Open the latches and along the red arrowhead direction as the picture to open other latches. Step 1: Remove the stand base ASSY 1.
  • Page 38 Meridian 3 Step 3: Remove the bezel 1. Remove the five screws that secure the connectors. 1. Remove the two screws to remove the IR boards. 2. Remove the eight screws to remove the power board and scaler board from the main frame. 2.
  • Page 39: Repair Flow Chart

    Meridian 3 11. Repair Flow Chart 1. No Power No power Check power cable is Re-plug the power cable tightened? Check Power “On/Off” Turn on the Power “On/Off” switch is “On”? Check the LED Check the AC power indicator is OK? Replace the power board and check connections Replace main board and check connections Replace key board and check connections...
  • Page 40 Meridian 3 No Video (Power LED White) No Video (Power LED White) Press the power Replace the main board button is OK? Replace the power The end board and connection Replace the main The end board and connection Check the FFC cable Replace the FFC cable or panel or panel...
  • Page 41 Meridian 3 3. DIM DIM (image overlap, focus or flicker) Reset in factory mode The end Set to the optimal The end frequency, select the recommended frequency Readjust the phase and pixel The end clock in the user mode Pull out signal cable and Check the signal cable check “Self Test Feature and the PC...
  • Page 42 Meridian 3 4. Color is not optimal Color is not optimal Color shift Miss color Reset the factory mode Replace the signal cable In the user mode, set the “color settings” until customer satisfy The end Pull out the signal cable and check the screen color display is normal? Replace the signal cable or PC...
  • Page 43: Isp Instructions

    Meridian 3 12. ISP Instruction Note: Take the 227E3LPH ISP SOP for example (the 227E3QPH SOP is almost the same as 227E3LPH) When do the parts, need the tools as follow: 1. An i486 (or above) personal computer or compatible. 2.
  • Page 44 Meridian 3 Click “Finish” to complete the USB serial port driver installation.
  • Page 45 Meridian 3 12.3 Install the ISP tool and run it: 1. Double-click to install ISP program. 2. Double-click to run the ISP tool. 3. Set the parameters to restore the HDCP key.
  • Page 46 Meridian 3 4. Setup ISP tool. Click “Setup ISP tool” to open the configuration window. 5. Configuration for ISP tool. Tick “FTDI”.
  • Page 47 Meridian 3 6. Load the F/W you want to upgrade. 7. Start to program. Click “Auto” to start programming.
  • Page 48 Meridian 3 8. Programing success. There will be the message in the red frame after successful programming. 12.4 Check the firmware version and reset the factory setting Check the firmware version 1. Connect the video source and power off the monitor. 2.
  • Page 49: Troubleshooting

    Meridian 3 Reset the factory setting Power on the monitor and open the user menu. Do factory reset: Setup – Reset – Yes. Factory reset will turn off “Burn in” mode which screen color switches among red, green, blue and black. 12.5 Troubleshooting: When can’t upgrade, please retry below several ways to upgrade.
  • Page 50: Ddc Instructions

    Meridian 3 13. DDC Instruction Note: Take the 227E3LPH EDID SOP for example (the 227E3QPH SOP is almost the same as 227E3LPH) General DDC Data Re-programming In case the main EEPROM with Software DDC which store all factory settings were replaced because a defect repaired monitor’...
  • Page 51 2. Put the EDID data and “config.ini” files into one folder named Philips 227E3LPH. 3. Copy the folder named Philips 227E3LPH to the “DDC” folder (It must be “DDC” instead of other names), and put the “DDC” folder and “HDMISinglePort.exe” into the same folder.
  • Page 52 Meridian 3 2. Choose the Analog +DVI ”, and click “Loadfile” to set the parameters as the below picture: 3. Click the “Next” to load the EDID file.
  • Page 53 Meridian 3 4. Select the “Philips 227elph” and then click “OK”, the tool will read the EDID information: 5. Choose the “Only connect HDMI” and “Write SN”, and key in the 14 digital S/N that must be the same as the S/N...
  • Page 54 Meridian 3 6. Click the “Program” to start programming after monitor power on. When it shows “Analog: PASS!, SN write OK!, DVI: PASS! and HDMI: PASS!”. The EDID and SN writing process are finished. 13.5 Check the SN 1. Connect the video source and power on monitor. 2.
  • Page 55 Meridian 3 227E3QPH EDID Analog 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ----------------------------------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 8E C0 94 BA 0A 00 10| 10 15 01 03 6E 30 1B 78 2A FC A5 A0 54 4E A0 27 20| 12 50 54 BD 4B 00 D1 C0 81 80 95 0F 95 00 B3 00 30| 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40| 45 00 E0 0C 11 00 00 1E 00 00 00 FF 00 31 33 32...
  • Page 56 Meridian 3 800 x 600 @ 60Hz VESA Established Timings 2:4B 800 x 600 @ 75Hz VESA 1024 x 768 @ 60Hz VESA 1024 x 768 @ 75Hz VESA 1280 x1024 @ 75Hz VESA Established Timings 3:00 <-Standard Timing Identification: -> 1920 x 1080 @ 60Hz 1280 x 1024 @ 60Hz 1440 x 900 @ 75Hz...
  • Page 57 Meridian 3 Digital 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ----------------------------------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 8E C0 94 BA 0A 00 10| 10 15 01 03 80 30 1B 78 2A FC A5 A0 54 4E A0 27 20| 12 50 54 BD 4B 00 D1 C0 81 80 95 0F 95 00 B3 00 30| 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40| 45 00 E0 0C 11 00 00 1E 00 00 00 FF 00 31 33 32...
  • Page 58 Meridian 3 Established Timings 2:4B 800 x 600 @ 75Hz VESA 1024 x 768 @ 60Hz VESA 1024 x 768 @ 75Hz VESA 1280 x1024 @ 75Hz VESA Established Timings 3:00 <-Standard Timing Identification: -> 1920 x 1080 @ 60Hz 1280 x 1024 @ 60Hz 1440 x 900 @ 75Hz 1440 x 900 @ 60Hz...
  • Page 59 Meridian 3 HDMI 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F --------------------Block 0-------------------- 00| 00 FF FF FF FF FF FF 00 41 0C 8E C0 94 BA 0A 00 10| 11 15 01 03 80 30 1B 78 2A FC A5 A0 54 4E A0 27 20| 12 50 54 BD 4B 00 D1 C0 81 80 95 0F 95 00 B3 00 30| 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40| 45 00 E0 0C 11 00 00 1E 00 00 00 FF 00 31 33 32...
  • Page 60 Meridian 3 <-Established Timings: -> Established Timings 1: BD 720 x 400 @ 70Hz VGA, IBM 640 x 480 @ 60Hz VGA, IBM 640 x 480 @ 67Hz Apple, Mac II 640 x 480 @ 72Hz VESA 640 x 480 @ 75Hz VESA 800 x 600 @ 60Hz VESA Established Timings 2:4B 800 x 600 @ 75Hz VESA...
  • Page 61 Meridian 3 ------------------------------------------------------- Block 1: Extended Block Type: CEA 861B Detailed Timing Blocks start at Byte: 22 DTV Underscan YES DTV Basic Audio YES YCbCr (4:4:4) YES YCbCr (4:2:2) YES <-Video Short Block Description: -> 640 x 480 P 59.94/60Hz 4:3 720 x 480 P 59.94/60Hz 4:3 720 x 480 P 59.94/60Hz 16:9 1920 x 1080 I 59.94/60Hz 16:9...
  • Page 62 Meridian 3 Detailed Timing Descriptions: 720x480 @ 60Hz H Image Size: 480 mm V Image Size: 268 mm Pixel Clock: 27 Hz Refreshed Mode: Non-Interlaced Detailed Timing Descriptions: 1280x720 @ 60Hz H Image Size: 480 mm V Image Size: 268 mm Pixel Clock: 74 Hz Refreshed Mode: Non-Interlaced Detailed Timing Descriptions: 720x576 @ 50Hz...
  • Page 63: White Balance, Luminance Adjustment

    Meridian 3 14. White Balance, Luminance Adjustment 1. Apparatuses and program: analyzer CA-210, PC, tool, FGA adjustment program (Philips LEDFGA.DDCI), Pattern generator. 2. Equipment installation: a. Connect analyzer CA-210 to PC by USB connector, install drive program CA-SDK Ver4.00 for CA-210 and restart PC after finish installing b.
  • Page 64 Meridian 3 5. Color Temp confirmation Connect the signal to the monitor, the monitor displays white-picture, use CA-210 to measure the Color Temp of the screen center and select the OSD to make sure whether the Color Temps accord with the SPEC. 11500K 8200K 7500K...
  • Page 66: Recommended & Spare Parts List

    Meridian 3 16. Recommended & Spare Parts List Recommended Parts List for 227E3QPHSU/94 Item Location PCM Codes Description Remark FQ106 A34G2670AMCA2M0130 BEZEL L215W-Uph1d-s1 FQ004 KEPCAQP3 KEY BOARD ASSY FQ007 IRPCAQA7 IR BOARD ASSY FQ015 LEPCAQP1 LED BOARD ASSY FQ007 IRPCAQT1 IR BOARD ASSY E750 750GBG215F3C13M0PH...
  • Page 67 Meridian 3 U106 056G 662 48 ESD PROTECT AZC399-04S.R7G SOT23-6L U107 056G 662 48 ESD PROTECT AZC399-04S.R7G SOT23-6L U109 056G 662 48 ESD PROTECT AZC399-04S.R7G SOT23-6L U053 056G 627911 IR 38KHZ KSM-603TM2M CN053 095G820H 3X507 HARNESS 3P(SANW)-3P(A1253HA) 170MM U052 056G 192 25 D-AMP AS358MTR-E1 SOIC-8 U001 056G 669 10...
  • Page 68 Meridian 3 FQ110 A37G0251011 HINGE 21.5 FQ125 A34G2576AFL 1B0100 STAND FQ205 803GQA44231 L215WA-Uph1-s1 227E3L EPS ASSY FQ002 756GQBCB PL003 00 SCALER BOARD ASSY(CBPCANUP1Q2) U402 100GPNGI00GNT1 MCU ASSY(056G2233 11) CN602 033G3802 5B Y CONNECTOR 5P 2.0 CN411 033G3802 5B Y WEAFER CN406 033G3802 7B Y WAFER...
  • Page 69 Meridian 3 R118 061G0402101 JT RST CHIP 100R 1/16W 5% TZAI YUAN R702 061G0402102 JI RST 0402 1K 5% 1/16W TA-I R129 061G0402102 JT RST CHIP 1K 1/16W 5% TZAI YUAN R410 061G0402103 JI TEST ONLY RST 0402 10K 5% 1/16W TA-I R632 061G0402103 JT RST CHIP 10K 1/16W 5% TZAI YUAN...
  • Page 70 Meridian 3 R420 061G0603560 JT RST CHIP 56R 1/10W 5% TZAI YUAN R455 061G1206221 JI RST 1206 220R 5% 1/4W R455 061G1206221 JT RST CHIPR 220 OHM +-5% 1/4W TZAI YUAN C621 065G040210412K CAP 0402 0.1UF 10% 16V X7R C412 065G040210412K CAP CHIP 0402 100nF 16V X7R C715...
  • Page 71 Meridian 3 CN053 095G820H 3W507 HARNESS 3P(SANW)-3P(A1253HA) 170MM CN053 095G820H 3X507 HARNESS 3P(SANW)-3P(A1253HA) 170MM R065 061G0805101 JF RST 0805 100R 5% 1/8W R065 061G0805101 JT RST CHIP 100R 1/8W 5% TZAI YUAN C059 065G080510432K CAP CHIP 0805 100N 50V X7R +/-10% C059 065G080510432K CAP CHIP 0805 0.1UF K 50V X7R...
  • Page 72 Meridian 3 C920 065G306K6812BW CAP Y1 680PF 10% 250V Y5P C900 065G306M3322B3 CAP Y1 3.3NF 20% 250V Y5U C900 065G306M3322BP CAP Y1 3.3NF 20% 250V Y5U C903 067G 40Z47015H EC 47uF M 450V 13*36mm C903 067G 40Z47015K EC 47UF 20% 450V 12.5*35 C903 067G 40Z47015L EC 47UF 20% 450V 12.5*35...
  • Page 73 Meridian 3 R812 061G0603101 JF RST CHIPR 100 OHM +-5% 1/10W FENGHUA R812 061G0603101 JI RST 0603 100R 5% 1/10W TA-I R810 061G0603102 JF RST CHIPR 1K OHM +-5% 1/10W FENGHUA R810 061G0603102 JT RST CHIP 1K 1/10W 5% TZAI YUAN R806 061G0603103 JF RST CHIPR 10K OHM +-5% 1/10W FENGHUA...
  • Page 74 Meridian 3 R921 061G08051501FT RST CHIPR 1K5 +-1% 1/8W TZAI YAUN R921 061G08051501FY RST CHIP 1K5 1/8W 1% R920 061G0805221 JI RST CHIPR 220 OHM +-5% 1/8W 0805 R920 061G0805221 JT RST CHIP 220R 1/8W 5% TZAI YUAN R926 061G08054701FF RST CHIPR 4.7KOHM +-1% 1/8W FENGHUA R926 061G08054701FT...
  • Page 75 Meridian 3 D904 093G 6452452T SWITCHING 1N4148-B4006 0.2A 100V DO-35 R919 061G152M47852T SY RST MOFR 0.47 OHM +-5% 2WS FUTABA R919 061G152M47852T HX RST MOFR 0.47 OHM +-5% 2WS Q903 057G 419 18 T SMALLTRAN 2SD1207-T-AE 2A 60V MP Q903 057G 761 16 TRA KTD1028 KEC IC903...
  • Page 78: General Product Specification

    4.2 Brightness/ Brightness Uniformity 4.3 Color Temperature Adjustment 5. Mechanical Characteristics 5.1 Cosmetic 5.2 Mechanical Data Files 5.3 Location of Philips Logo 5.4 Gap between Panel and Front Bezel 5.5 Location of Control Icons 5.6 Color for Resin/Paint 5.7 Fire Enclosure Request...
  • Page 79: Foreword

    All optical characteristics are determined according to panel specification after warming up longer than 30 minutes. 2. Product Profile This display monitor unit is a color display monitor enclosed in PHILIPS styling cabinet which has an integrated tilt base. 2.1 EDID Header 1 User visible strings on .inf file...
  • Page 80: Lcd

    Scaler should be capable of below items. 1) Scaler must support color engine for Image enhancement feature (SmartImage) 2) Scaler must have enough memory to support PerfecTune feature and Philips OSD 3) Scaler must support SmartContras, 20M: 1 DCR preferred...
  • Page 81: Interface Signals

    Meridian 3 signal is detected. Monitor will automatically optimize resolution and frequency whenever connected to different signal source. When press the “Auto”, the screen also show a status bar. During adjustment period, a status bar will show on screen from 0% to 100% to indicate the progress of adjustment. Auto adjustment: new timing &...
  • Page 82 Meridian 3 1080i 1920 x 1080 50Hz , 60Hz 1080p 1920 x 1080 50Hz, 60Hz Picture Centering: H&V<=0.5% (for TV, 480i/p, 576p, 720p, 1080i/p) OverScan: 1. RGB signal: OFF (no this function) 2. YUV signal: (Video timming) ON (Be used and set ON/OFF, but only 1080p definde is OFF) PC timing: to follow PC timing table TMDS/+5V/DDC/HPD/CEC Signals (TMDS Signal)
  • Page 83: Interface

    Meridian 3 d) Display Port (option, refer to Quick specification table) Follow Display Port 1.1 specification e) USB Hub 2.0 (option, refer to Quick specification table) USB port (1 upstream, 2 or 4 downstream) f) Audio in (option, refer to Quick specification table) Input signal: 1Vrms Loudspeaker: stereo of RMS Power Frequency range: (WAIT FOR SUPPLIER INPUT)
  • Page 84: Timing Requirement

    Meridian 3 Pin Assignment: Signal Assignment Signal Assignment T.M.D.S. data2- No Connect T.M.D.S. data2+ +5V Power T.M.D.S. data2 shield Ground (for +5V) No Connect Hot plug detect No Connect T.M.D.S. data0- DDC clock T.M.D.S. data0+ DDC data T.M.D.S. data0 shield No Connect No Connect T.M.D.S.
  • Page 85: Osd/Keypad Functions

    OSD Translation Russian, Simplified Chinese, Portuguese, Turkish (9) Power On Logo: Power On Show up Philips logo 3 seconds Power ON Logo Change to input signal. This picture is reference only. The official drawing will send out by PM. Stand-alone- On:...
  • Page 86: Horizontal Scanning

    Meridian 3 3.5 Horizontal scanning Sync polarity : Positive or Negative Scanning frequency : 30 - 83 KHz PS: Item 3.4 and 3.5, as far as possible to be display (another Horizontal and Vertical) 3.6 Vertical scanning Sync polarity : Positive or Negative Scanning frequency : 56 - 76 Hz 3.7 Power input connection...
  • Page 87: Vga Display Identification

    In accordance with DVI requirement (DDWG digital Visual Interface revision 1.0) use DDC-2B, DDC/CI, and EDID V1.3 3.11 DDC /CI Support and Smart Manage /Control In accordance with VESA DDC/CI and MCCS ver.2.0, the monitor should be workable with, Philips SmartManage, SmartControl V6.1, and Portrait Display Tune at least 3.12 Hot-key definition 3.13 Smart Image...
  • Page 88 Meridian 3 3.15.4 Audio Amplifier The amplifier shall provide two channels of audio up to 1.5 Watts per channel from 100Hz to 20 KHz, based upon an audio signal input of 1.0Vrms per channel. 3.15.5 Volume Control For monitors with a manual volume control, the direction (at the bottom) of the bezel volume control is “-”...
  • Page 89 Meridian 3 Sensor distance measure: 1. Cotton material color: black 2. Monitor center straight distance (90 deg) 3. Body with: about 40 cm 4. Body horizontal move: Monitor center +/- 5cm Anti-interference between two monitors Monitors must have anti-interference methods (coding .ect) to prevent monitors to talk to each other. Power sensor functional behavior Time Period 60sec...
  • Page 90: Visual Characteristics

    Meridian 3 3.17 Pixel-orbiting function 3.17.1 On wide view angle models (IPS/e-IPS/AMVA/PVA/MVA) 3.17.2 Functional description Every 1 min to shift one pixel for whole picture, 8 min to original point and Routing path (H-1, V+1, H+1, V-1, V-1, H+1, V+1, H-1) 4.
  • Page 91: Mechanical Characteristics

    5. Mechanical Characteristics 5.1 Cosmetic - Philips ID 5.2 Mechanical data files - ProE files required 5.3 Location of Philips logo - Per Philips make-up sheet 5.4 Gap between panel and front bezel < 1.2 mm 5.5 Location of Control icons - Per Philips Graphic sheet 5.6 Color for resin/paint -...
  • Page 92: If Paint Is Used

    MMD request metal plate in Kensington hole. 5.15 Label Regulatory label / Carton label should follow Philips requirement. Detail document refer to Philips Engineering Reference Book. 5.16 Product dimension / Weight (Refer to Philips approved SHT 191/ SHT560) Unit dimension Packed unit dimension: Net weight...
  • Page 93: Transportation

    3. Cold Drop test (for design reference) Un-package test 1. Sine vibration (operating) 2. Half sine shock test (non operation) 5.18 Pallet / Container loading (Refer to Philips approved SHT 560) Transportation standards refer to TYE-M0002, UAN-D1534 and UAW-0309. Air shipment - Sea container 20'(pallet/slip sheet)
  • Page 94: Environmental Characteristics

    Meridian 3 Transportation request for China and India Container loading for China and India Truck loading Transportation request for EU Land 45‘Truck and Trailer (800X1200mm pallet) Land 45‘Truck and Trailer (1000X1200mm pallet) for UK 6. Environmental Characteristics The following sections define the interference and susceptibility condition limits that might occur between external environment and the display device.
  • Page 95 4. When the HV circuitry is operating properly there is no possibility of an x- tube must be the same type as the original, including suffix letter, or a Philips radiation problem. High voltage should always be kept at the manufacturer's approved type.

Table of Contents