Sanyo VPC-WH1W Service Manual page 25

Adjustment value determination is effectuated using the
"CHECK", "CHECK_FS", "MS", "MS_M", "MS_C", "MS_C2",
"MS_C3", "MS_C4", "MS_C5", "MS_Z", "MS_M_Z", "MS_C_Z",
"MS_C2_Z", "MS_C3_Z", "MS_C4_Z", "MS_C5_Z", "MS_Z2",
"MS_M_Z2", "MS_C_Z2", "MS_C2_Z2", "MS_C3_Z2",
"MS_C4_Z2", "MS_C5_Z2", "IRIS_PWM1", "IRIS_PWM2",
"IRIS_PWM3" and "IRIS_PWM4" values. If
CHECK = wc0, wc1, wc2
CHECK_FS = wnc0, wnc1, wnc2
MS = ms1, ms2
MS_M = ms3, ms4
MS_C = ms5, ms6
MS_C2 = ms7, ms8
MS_C3 = ms9, ms10
MS_C4 = ms11, ms12
MS_C5 = ms13
MS_Z = ms14, ms15
MS_M_Z = ms16, ms17
MS_C_Z = ms18, ms19
MS_C2_Z = ms20, ms21
MS_C3_Z = ms22, ms23
MS_C4_Z = ms24, ms25
MS_C5_Z = ms26
MS_Z2 = ms27, ms28
MS_M_Z2 = ms29, ms30
MS_C_Z2 = ms31, ms32
MS_C2_Z2 = ms33, ms34
MS_C3_Z2 = ms35, ms36
MS_C4_Z2 = ms37, ms38
MS_C5_Z2 = ms39
IRIS_PWM1 = s1, s2
IRIS_PWM2 = s3, s4
IRIS_PWM3 = s5, s6
IRIS_PWM4 = s7
the adjustment values fulfill the conditions below, they are
determined as within specifications.
Adjustment value determination
wc0=128 ± 2, wc1=128 ± 2, wc2<=255
wnc0=128 ± 2, wnc1=128 ± 2, wnc2<=255
2090<=ms1<=3500, 990<=ms2<=1620,
1860<=ms3<=2730, 1680<=ms4<=2440,
1510<=ms5<=2210, 1430<=ms6<=2150,
1380<=ms7<=2100, 1370<=ms8<=2080,
1370<=ms9<=2080, 1350<=ms10<=2060,
1230<=ms11<=1940, 1150<=ms12<=1870,
1040<=ms13<=1760, 2400<=ms14<=3800,
990<=ms15<=1620, 1990<=ms16<=3000,
1730<=ms17<=2500, 1510<=ms18<=2210,
1430<=ms19<=2150, 1380<=ms20<=2100,
1370<=ms21<=2080, 1370<=ms22<=2080,
1350<=ms23<=2060, 1230<=ms24<=1940,
1150<=ms25<=1870, 1040<=ms26<=1760,
2400<=ms27<=3910, 990<=ms28<=1620,
2120<=ms29<=3320, 1970<=ms30<=3030,
1860<=ms31<=2780, 1820<=ms32<=2650,
1730<=ms33<=2560, 1640<=ms34<=2480,
1520<=ms35<=2360, 1360<=ms36<=2200,
1230<=ms37<=1940, 1150<=ms38<=1870,
1040<=ms39<=1760
s1>s2>s3>s4>s5>s6>s7
Adjustment values other than the above are irrelevant.
5. CMOS White Point Defect Detect Adjustment
Preparation:
POWER switch: ON
Adjustment method:
1. Double-click on the DscCalDi.exe.
2. Select "CCD Defect" on the LCD "Test", and click the "Yes".
3. After the adjustment is completed, OK will display.
4. Click the OK.
6. CMOS Black Point And White Point Defect Detect
Adjustment In Lighted
Camera
Preparation:
POWER switch: ON
Setting of pattern box:
Color temperature: 3100 ± 20 (K)
Luminance: 900 ± 20 (cd/m
Adjusting method:
1. Set a distance of 0.5-1.0 cm between the pattern box and
the camera.
2. Double-click on the DscCalDi.exe.
3. Select "CCD Black" on the LCD "Test", and click the "Yes".
4. After the adjustment is completed, the number of defect
will appear.
5. Click the OK.
– 25 –
Pattern box
(color viewer)
2
)