Now You Are Ready To Fly; Recognizing The Front And Back Of The Dart ™ 1.0; Automatically Take Off / Land; Speed Setting Button - Propel RC DART 1.0 Instruction Booklet

NOW YOU ARE READY TO FLY!

If you have successfully synced your DART ™ 1.0 to your controller as explained on page 4 you are now
ready to fly.Before beginning to fly your drone you should familiarize yourself with how to start and stop
the rotors,how to use your take off and auto land feature and how the controls work.please carefully read
and familiarize yourself with various control features explained in the next few pages.Once again as a
beginner pilot you should learn how to control your drone in a large open field or park on a day with zero or
very light wind.Do not try to fly your DART ™ 1.0 too high until you become a more experienced pilot.
RECOGNIZING THE FRONT AND BACK OF THE DART ™ 1.0
Even though the DART ™ 1.0 has four rotors there is still a
front or forward-facing direction and back or backwards-
facing direction.TheFront and forward-facing direction of the
DART ™ 1.0 is the side with two holes.The rear and back of the
DART ™ 1.0 is where the battery charging socket and the
power ON/OFF is.The DART ™ 1.0 when in flight will also help
you keep aware of the orientation with lighted LED lights in
the arms of the DART ™ 1.0
NOTE: The front of the copter displays WHITE LED lights and the
back of the copter displays RED LED lights.

AUTOMATICALLY TAKE OFF / LAND

Make sure you have properly synced The DART ™ 1.0.
• simply press the"start/land"button on the top of controller,your DART ™ 1.0 will automatically
take off.
• To stop or land the DART ™ 1.0 just press the"START/LAND"button again and the DART ™ 1.0 will
descend and land automatically.
Tips: You also can move the two control sticks simultaneously down to the inside corners, hold them till you
hear a "beep" and the blades start spinning. Release the control sticks and push the throttle stick slowly to
take off manually.
In case of emergency : to stop the rotors instantly, simply press the calibrate button on the top of
the cotroller, located in the center.

SPEED SETTING BUTTON

The DART ™ 1.0 has 4 speed settings; T(Training),1(SLOW),2(MEDIUM) and 3(HIGH).The Default
setting when you first turn on your DART ™ 1.0 is T(Traning).To exit T Mode and to increase the speed
simply press the speed button(see remote diagram on page 3).You will hear a beep and the speed
indicator will display the current speed setting with the Number.Number 1 indicates slow speed,2
indicates medium speed and 3 indicates high speed.

T (Training)MODE

Simply press and hold the Speed Setting Button; you will hear a long beep and the speed indicator will
change to "T." Now you are in T mode.T mode allows you to learn how to operate your DART ™ 1.0 at a
very slow speed.To exit T mode just press the speed setting button again.
AUTO-SHUT-OFF
In T-Mode and Mode 1 (with safety cage fitted),The DART ™ 1.0's motors will automatically shut off
when it comes into contact with the ground,walls or any other objects.This is a safety feature for
beginner pilots and is disabled in modes 2 and 3.
5

3/4 CHANNEL SELECTION

DART ™ 1.0 allows you to control your Quadrocopter in 3 channel mode (beginner) or 4 channel mode
(advanced flying).The DART ™ 1.0 default setting is 4 Channel mode.
To change to 3 Channel mode:
PRESS the 3CH button (see remote diagram on pg 3); you will hear 3 short beeps indicating the DART ™
1.0 now is set to 3CH mode.
To change back to 4 Channel mode:
PRESS the 4CH button (see remote diagram on pg 3); you will hear 4 short beeps indicating the Zipp
Nano™ is now set to 4CH mode.
UNDERSTANDING TRIM ADJUSTMENTS

Forward/Backward Trim

�• If your DART ™ 1.0 is moving forwards or backwards automatically,you may need to adjust the
Front
FORWARD/BACKWARD TRIM buttons.
•�If your DART ™ 1.0 flies forward,push and release the B TRIM button repeatedly until the
moving stops and proper flight is maintained.
•�If your DART ™ 1.0 flies backwards,push and release the F TRIM button in the same manner
until the problem is resolved.
• From time to time you may have to adjust the FORWARD/BACKWARD TRIM to ensure the
DART ™ 1.0 will hover in mid-air and respond accurately to your commands.
Forward/Backward
Trim
Back
Forward/Backward
Trim Controls

Banking Left/Right Trim

�• If your DART ™ 1.0 is not steadily hovering and is banking to the left or right automatically,you may
need to adjust the BANKING TRIM buttons.
•��If your DART ™ 1.0 banks to the left,push and release the R TRIM button repeatedly until the
banking stops and proper flight is maintained.
•��If your DART ™ 1.0 banks to the right,push and release the L TRIM button in the same manner until
the problem is resolved.
• From time to time you may have to adjust the BANKING TRIM to ensure the DART ™ 1.0 will steadily
hover in mid-air and respond accurately to your commands.
Banks Trim
3CH
4 CH Left/Right Banking
Controls
NOTE: The use of theTrim buttons are accompanied with a beep tone.A single long beep indicates the product is
centre-trimmed.No beeping after press the trim button indicates the product is trimmed to the maximum on a particular side.
If flying forward...
3CH 4CH
Push backward
trim button
Banks Trim
4CH
Push the "L" trim button to
increase left banking
sensitivity
If flying backward...
Push forward
trim button
Push "R" trim button to
increase right banking
sensitivity
6