Automatically Recording And Finalizing A Disc - Pioneer PDR-609 Operating Instructions Manual

1
1
DIGITAL ANALOG
REC LEVEL REC LEVEL
PUSH ENTER
ANALOG
L REC BALANCE R
MENU/
TEXT
DELETE
SYNCHRO
2
Legato Link Conversion
CD TEXT
3
◊ÛB - >?/
3
AUTO
SCROLL TIME MONITOR
MANUAL
TRACK NO.
WRITE
AUTO INPUT
ERASE FINALIZE MANUAL SELECTOR
2
1-track sync
All-track sync
AUTO/
•
REC SYNCHRO MANUAL
3
TIME A B C D E F
All-track sync w/ finalization
1 2 3
DISPLAY
G H I J K L M N O
/CHARA
4 5 6
SCROLL
P Q R S T U V W X Y Z
7 8 9
MENU/
MARK NAME
DELETE
10/0 >10 Record-pause (no sync)
4
¢
CURSOR
3
1 ¡
ENTER
7
REPEAT RANDOM NAME CLIP
8
FADER PROGRAM CHECK CLEAR
I NPUT
SKIP ID
SKIP PLAY
SELECTER
2
SET CLEAR
Î
Automatically
recording and
finalizing a disc
This is a variation on all-track synchro
recording on the previous page. After all
tracks on the source material have been
recorded, the recorder automatically
finalizes the disc.
You can also copy CD text digitally as long
as: it has not been copy-protected by the
manufacturer; the disc you want to copy is
not in program-play mode; you use a
completely blank CD-R.
Load a CD-R or CD-RW disc.
Check the display to make sure that there's
enough space on the disc for what you
want to record.
Press INPUT SELECTOR to
choose an input.
Pressing repeatedly
INPUT SELECTOR
switches the active input:
Analog - Optical - Coaxial
The display indicates the current input.
Make sure that the source is not
playing, then press SYNCHRO
three times.
Press repeatedly to change the
SYNCHRO
recording mode:
SYNC–1
SYNC–ALL
SYNC–FINAL
O1 O1 OO:OO
Synchro recording won't work if the source
is already playing!
The recorder goes into all-sync record
pause and the and
SYNC FINALIZE
indicators start to blink.
CD-R
SYNC–FINAL FINALIZE
SYNC
4 Getting started
The display shows all-track sync with
finalization, with the
indicators blinking to show that
FINALIZE
recording can start.
Note: If You want to record CD text
information as well, press
pressing
SYNCHRO
indicator will light.
4 Play the source.
Recording starts automatically.
If you press
SYNCHRO
the recorder will finish recording without
finalizing the CD-R.
5 After recording all tracks on the
source, the recorder starts
finalizing the disc.
After the recorder encounters about five
seconds of continuous silence, it assumes
the end of the source has been reached and
goes into all-sync record-pause.
Be careful: If the recorder detects
another signal or start ID (DAT or DCC) it
will start recording again!
If the recorder detects no signal for one
minute, finalization starts (no more
recording is possible after this so make
sure that there aren't any spaces of more
than one minute during the source you're
recording). See Automatically number-
ing tracks on page 33 to set the silence
threshold.
Finalization takes about two minutes,
during which time none of the buttons are
CD-R
SYNC-1 operative.
Never turn the power off during finaliza-
CD-R
tion!
SYNC
• If a digital signal is interrupted, the
CD-R
recorder continues recording. However,
FINALIZE
SYNC
if no signal has been detected within
five seconds, the recorder pauses
CD-R
recording and will not finalize the
disc—see Digital signal interruptions
on page 18.
• If the recorder reaches the end of the
disc, the recorder begins finalization.
Note: If you find that synchro recording
does not seem to work, see the trouble-
shooting section on pages 40–42 for
possible remedies.
and
SYNC
after
NAME
. The
CD TEXT
during recording,
21
En