Related Manuals for NatComm DS1
Summary of Contents for NatComm DS1
- Page 1 USER GUIDE For Technical Assistance call the Manufacturers direct ph 0800 530 8645 9AM - 5PM West Coast Pacific Time NATCOMM USA LLC Responsible Supplier Code NC...
-
Page 2: Table Of Contents
ADSL & Security Alarm Information Page Balance POT Adjustment Page PBX Installation and User Info Pages 14 - 15 Programming Options and Page Information Programming Procedure Page Troubleshooting Audio Problems Page 18 - 19 Specifications Pages 20 Warranty Information Pages 20 Page 2 Natcomm... -
Page 3: Description
Your DS1 Controller is completely TRANSPARENT in operation, so it will not affect the normal operation of your telephone line in any way. ONE or TWO Door Phones can be connected to the DS1 unit. They must be connected in parallel with each other. Either Door Phone can trigger a Door Phone call. - Page 4 DS1 can be used with MOST CORDLESS PHONE MODELS. However, a small number of CORDLESS PHONE MODELS may ignore the ring from DS1 and will NOT RING when there is a Door Phone call.
-
Page 5: Door Phone Options
DOOR PHONES Four Door Phones are for use with your DS1 and should be ordered separately: Model DP1 - SURFACE MOUNT Plastic injection moulded casing 2 Wire connectivity Basic audio clarity and volume Budget solution ... -
Page 6: Door Phone Covers
Door Phones, so that your Door Phone can be mounted ONTO a wall surface, rather than into it. Two separate surface mounting kits are available, to cater for the different sized DP2-DP5 Door Phones: Model SMK2 for DP2 Door Phones Model SMK3 for DP4, DP5 Door Phones Page 6 Natcomm... -
Page 7: Operation Summary
OPERATION SUMMARY When a visitor at your door or gate presses the call button on your supplied Door Phone, DS1 will ring all of the telephones connected to your line up to 10 times (the number of rings can be changed). -
Page 8: Installation Diagram
MODEL DS1 INSTALLATION Page 8 Natcomm... -
Page 9: Installation Instructions Pages
In the event of a malfunction or power cut, your telephone line will continue to operate. Your DS1 unit should be fitted inside the home or office. If it is fitted outside next to the Door Phone, then it MUST be fitted within a Water Proof enclosure. - Page 10 Double Telephone adaptor. VERY IMPORTANT NOTE - LOSS OF TELEPHONE SERVICE D) Should the DS1 device ever need to be removed, or if it becomes faulty, you will lose your telephone service. To overcome this, you should remove the cable from the LINE IN port of...
-
Page 11: Door Phone Connection
Power Connection - Connect Pins 3 & 6 (the 2 pins either side of the center 2 pins) of the 8 pin RJ45 socket of DS1, to the outside positions of the 4 position Phoenix Plug. Polarity is not important. -
Page 12: Usa And Canada Compliance
However it is ESSENTIAL to fit a SINGLE High Quality ADSL filter immediately ahead of the DS1 Controller. Failure to do so, or use of additional ADSL filters connected direct to your telephones, WILL cause problems in the operation of your DS1 Controller and ADSL service. -
Page 13: Balance Pot Adjustment
PHONE, as feedback interference will affect the Balance Pot settings. Move at least 15ft from the Door Phone. The Balance POT does not increase volume. Moving it when unnecessary may cause deterioration in audio quality or a loss of audio in 1 direction. Natcomm Page 13... -
Page 14: Pbx Installation And User Info Pages
In this situation, the incoming telephone line, prior to the system controller should be connected to the LINE IN port of the DS1 Controller and the LINE OUT port of the DS1 Controller should then be connected to the system controller. - Page 15 Diagram 1 - Connecting to the LAST LINE of a PBX system Last Line passes through the DS1 Last Line passes through our DS Controller Diagram 2 - Connecting to an UNUSED Trunk of a PBX system Important Note Line Input is not required for our DS Controller.
-
Page 16: Programming Options And
PROGRAMMING OPTION You can set the Number of Rings that DS1 will generate when a visitor presses the Call Button on your Door Phone. The Default setting is 10 Rings. You may wish to change this to prevent a Door Phone call being answered by your answering machine. -
Page 17: Programming Procedure
TURN OFF POWER TO YOUR UNIT SWITCH ON POWER AND PRESS # (WITHIN 30 SECONDS) You must use a telephone connected to DS1. YOUR UNIT WILL OUTPUT 3 SHORT ‘BEEPS’ Do not proceed until you have heard 3 short beeps. If you do not hear 3 beeps, return to the start (1). -
Page 18: Troubleshooting Audio Problems
EMI. Please TURN OFF any SWITCH MODE POWER SUPPLIES located near the DS1 controller (and its power supply) and test if the problem is resolved. If the DS1 Power Supply is connected to an Uninterruptable Power Supply, remove it and test if the problem is resolved. - Page 19 These devices are available from your Dealer If your problem is still unresolved, please call NATCOMM on ph 0800 530 8645 to report the above results and arrange for further advise or repair. Please call 0800 530 865 for additional assistance.
-
Page 20: Specifications Pages
Damage caused to this device or attached equipment by lightning strikes or over voltage surge is not covered under this warranty. THE CASE IS SEALED AT THE FACTORY. OPENING THE CASE WILL VOID THE WARRANTY. Page 20 Natcomm...