Do you have a question about the SOPHIA and is the answer not in the manual?
Questions and answers
Chris
April 10, 2025
To initiat self clean I hole the turbo self clean button down for more than two seconds???
1 comments:
Mr. Anderson
April 10, 2025
To initiate the self-clean feature on the Cooper & Hunter SOPHIA, press and hold the TURBO/SELF CLEAN button for more than 2 seconds. To disable the self-clean feature, press and hold the same button again for more than 2 seconds.
CONTENTS Handling the remote controller ............Remote controller Specifications........... Function buttons ................Indicators on LCD ................How to use the buttons ..............Auto operation................. Cooling/Heating/Fan operation............Dehumidifying operation ............... Adjusting air flow direction............Timer operation................SLEEP/FRESH function..............LED/FOLLOW ME function ............14 TURBO/SELF CLEAN function .............
Handling the remote controller Location of the remote controller. Use the remote controller within a distance of 26,2ft (8 meters) from the appliance, pointing it towards the receiver. Reception is confirmed by a beep. CAUTIONS The air conditioner will not operate if curtains, doors or other materials block the signals from the remote controller to the indoor unit.
Remote Controller Specifications 3.0V(Dry batteries R03/LR03×2) Rated Voltage Signal Receiving 26,2ft ( Range Environment 23 F~140 F Performance Feature 1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only model without), and FAN. 2. Timer Setting Function in 24 hours. 3. Indoor Setting Temperature Range: 62 F~86 F. 4.
Function buttons ON/OFF Button Operation starts when this button is pressed and stops when this button is pressed again. MODE Button Each time the button is pressed, the operation mode is selected in a sequence of following: AUTO COOL HEAT NOTE: Heat mode is for Cooling &...
Function buttons RESET Button: When you press the recessed RESET button, all current settings are cancelled and the control will return to the initial settings. UP Button( Push this button to increase the indoor temperature setting in 1 F increments to 62 F. ON/OFF DOWN Button( TEMP...
Page 7
FAN SPEED Button Used to select the fan speed in four steps: AUTO HIGH TIMER ON Button Press this button to initiate the auto-on time sequence. Each press will increase the auto-timed setting in 30 minutes increments. When the setting time displays 10H, each ON/OFF press will increase the auto-timed setting TEMP...
Indicators on LCD Transmission Indicator This transmission indicator lights when remote controller transmits signals to the indoor unit. Mode display Displays the current operation mode. Including auto( ), cool( ), dry( ), heat( ) (Not applicable to cooling only models), fan( and back to auto( Temp./Timer display auto cool dry heat...
How to use the buttons Auto operation Ensure the unit is plugged in and power is available. The OPERATION indicator on the display panel of the indoor unit starts flashing. 1. Press the MODE button to select Auto. 2. Press the UP/DOWN button to set the ON/OFF desired temperature.
Dehumidifying operation Ensure the unit is plugged in and power is available. The OPERATION indicator on the display panel of the indoor unit starts flashing. 1. Press the MODE button to select DRY mode. 2. Press the UP/DOWN buttons to set the desired temperature.
Timer operation Press the TIMER ON button can set the auto-on time of the unit. Press the TIMER OFF button can set the auto-off time of the unit. To set the Auto-on time. 1. Press the TIMER ON button. The remote controller shows TIMER ON, the last Auto-on setting time and the signal "h"...
CAUTION The effective operation time set by the remote controller for the timer function is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15,16,17, 18, 19, 20, 21, 22, 23 and 24.
Page 13
TIMER OFF TIMER OFF (Auto-off Operation) The TIMER OFF feature is useful when you want the unit to turn off automatically after you go to bed. The air conditioner will stop automatically at the set time. Example: Stop To stop the air conditioner in 10 hours. 1.
TIMER ON → TIMER OFF (Off → Start → Stop operation) TIMER ON OFF This feature is useful when you want to start the air conditioner before you wake up and stop it after you leave the house. Example: Start To start the air conditioner 2 hours after setting, Stop and stop it 5 hours after setting.
LED/FOLLOW ME function Press this button less than 2nds will initiate LED function. And if keep pressing this button more than 2nds,the FOLLOW ME function is initiated. When the Follow Me function is activated, the remote display is actual temperature at its location.
Page 16
FAQs Why does the fan continue to run even when the unit is not cooling or heating? To maintain consistent temperatures and minimize energy-loss from constant starts and stops, the fan keeps air flowing past the thermostat. What temperature is displayed on the remote controller? The remote always displays your desired indoor temperature.
Need help?
Do you have a question about the SOPHIA and is the answer not in the manual?
Questions and answers
To initiat self clean I hole the turbo self clean button down for more than two seconds???
To initiate the self-clean feature on the Cooper & Hunter SOPHIA, press and hold the TURBO/SELF CLEAN button for more than 2 seconds. To disable the self-clean feature, press and hold the same button again for more than 2 seconds.
This answer is automatically generated