Table of Contents
Advertisement
MODE
4
Each time you press this button,a mode is selected in a sequence that goes from AUTO, COOL,DRY, FAN,and HEAT *, as the
following:
AUTO
COOL
After energization, AUTO mode is defaulted. In AUTO mode, the set temperature will not be displayed on the LCD, and the unit
will automatically select the suitable operation mode in accordance with the room temperature to make indoor room comfortable.
FAN
5
This button is used for setting Fan Speed in the sequence that goes from AUTO,
to Auto.
Auto
SWING
6
Press this button to set up &down swing angle, which circularly changes as below:
This remote controller is universal . If any command
indicates the guide louver swings as:
I FEEL
7
Press this button to turn on I FEEL function. The unit automatically adjust temperature according to the sensed temperature. Press this button again to
cancel I FEEL function.
/
8
Press this button to achieve the on and off of healthy and scavenging functions in operation status.Press this button for the first time to start scavenging
function; LCD displays"
Press this button for the third time to quit healthy and scavenging functions simultaneously. Press the button for the fourth time to start healthy function;
LCD display "
". Press this button again to repeat the operation above.
SLEEP
9
●Press this button, can select Sleep 1 (
is defaulted.
●Sleep 1 is Sleep mode 1, in Cool, Dehumidify modes: sleep status after run for one hour, the main unit setting temperature will increase 1 ℃,setting
temperature increased 2℃, the unit will run at this setting temperature; In Heat mode: sleep status after run for one hour, the setting temperature will
decrease 1 ℃, 2 hours, setting temperature will decrease 2 ℃, then the unit will run at this setting temperature.
●Sleep 2 is sleep mode 2, that is air conditioner will run according to the presetting a group of sleep temperature curve.
●Sleep 3- the sleep curve setting under Sleep mode by DIY:
(1) Under Sleep 3 mode, press "Turbo" button for a long time, remote control enters into user individuation sleep setting status, at this time, the time of
remote control will display "1hour ", the setting temperature "88" will display the corresponding temperature of last setting sleep curve and blink (The first
entering will display according to the initial curve setting value of original factory);
(2) Adjust "+" and "-" button, could change the corresponding setting temperature, after adjusted, press "Trubo "button for confirmation;
(3) At this time, 1hour will be automatically increased at the timer postion on the remote control, (that are "2hours " or "3hours " or "8hours "), the place of
setting temperature "88" will display the corresponding temperature of last setting sleep curve and blink;
(4) Repeat the above step (2) ～ (3) operation, until 8hours temperature setting finished, sleep,curve setting finished, at this time, the remote control will
resume the original timer display;temperature display will resume to original setting temperature.
●Sleep3- the sleep curve setting under Sleep mode by DIY could be inquired:
The user could accord to sleep curve setting method to inquire the presetting sleep curve, enter into user individuation sleep setting status, but do not
change the temperature, press "Turbo" button directly for confirmation.Note: In the above presetting or enquiry procedure, if continuously within10s, there
is no button pressed, the sleep curve setting within 10s, there is no button pressed, the sleep curve setting status will be automatically quit and resume to
display the original displaying. In the presetting or enquiry procedure, press "ON/OFF" button, "Mode" button, "Timer"button or "Sleep" button, the sleep
curve setting or enquiry status will quit similarly.
TEMP
10
Press this button, could select displaying the indoor setting temperature or indoor ambient temperature.When the indoor unit firstly
power on it will display the setting temperature, if the temperature's displaying status is changed from other status to"
the ambient temperature, 5s later or within 5s, it receives other remote control signal that will return to display the setting
temperature. if the users haven't set up the temperature displaying status,that will display the setting temperature.
DRY
FAN
HEAT*
Low speed
Low-Medium speed
Medium-High speed
OFF
,
". Press the button for the second time to start healthy and scavenging functions simultaneously; LCD displays"
), Sleep 2 (
),Sleep 3 (
*Note:Only for models with heating function.
Medium speed
High speed
or
is sent out,the unit will carry out the command as
) and cancel the Sleep,circulate between these, after electrified, Sleep Cancel
,
,
,
,
, to then back
" and "
" .
",displays
Hide quick links:
Advertisement
Table of Contents
