Contents 1 Safety Instruction 9 Center Part Function Instruction 2 Product Overview 9.1 Center Volume Setting 3 Front Panel Connections 9.2 Direct Sound to the Center, 4 Rear Panel Connections Effect to Center Volume Setting 5 Boot Screen 9.3 Center Musical Delay, 6 Music Function Instructions Music to Center Volume Set 6.1 Music Input Line Option...
IMPORTANT SAFETY INSTRUCTIO The lightning flash with arrowhead synbol within an equilateral triangle is intended to alert the user to the CAUTION presence of uninsulated dangerous voltage within the RISK OF ELECTRIC SHOCK product's enclosure, that may be of sufficient magnitude DO NOT OPEN to constitute a risk of electric shock to persons.
Product Overview USER PROGRAM PARAMETER STORE MUS VOL/EDIT(PUSH) MIC VOL EFF VOL MIC ENHANCE MIC MODE EFF MODE MUS MODE MAIN MODE CENT MODE SUB MODE The product uses 56-bit high-performance DSP and 24bit AD / DA, 48kHz sampling frequency of professional digital multi-channel karaoke processor high performance professional concerts effect (reverb, echo, dual-echo, reverb + echo).
Front panel instruction USER PROGRAM PARAMETER STORE MUS VOL/EDIT(PUSH) MIC VOL EFF VOL MIC ENHANCE MIC MODE EFF MODE MUS MODE MAIN MODE CENT MODE SUB MODE 7 8 9 10 11 12 13 14 16 17 1 3-ways microphone input jack and volume control potentiometer 2 132 * 32 dot- matrix LCD display is used to display a variety of menus and parameter adjustment information.
4 Rear Panel instruction 12 13 14 Made In China MIC INPUT INPUT ADJUST RS232 S/PDIF CENT ∞ +3dB ~90V-250V POWER 50-60Hz OPTIC LINE REMOTE AUX OUT REC OUT RIGHT LEFT VIDEO AUDIO INPUT 1 Power Switch (T1AL/250VAC) 2 Standard IEC Power Input (~ 90V-220V) 3 RS232 interface 4 Digital Audio Output (S / PDIF) 5 The OPTIC Interface (fiber interface)
5 Power-On processor. Connect power cable, press the power switch on the rear panel, screen display trademark will be shown as below: Then the version No#, the processor unit starts loading data (the boot loaded data can be set after the boot, there are 5 options: [the last memory before turn-off], [1-4 user program],here show the selected set).
Music part operating instructions 6.1 Line select function of music input 6.1.1 analog music input 3-way analog music input line: background music, Input 1, Input 2 Potentiometer adjustment function, adjustment range: - 8 ~ +3 db Method 1: continuously press panel buttons "music mode" until display to the music input selection screen, as shown below: Music Input: Panel...
6.4. Music PEQ setting PEQ: 7 bands Type: Parametric equalization filters(can be set as low/high-tone filter), graphic equalization (the 7 band can be set up as a high-cut). Frequency range: 20Hz - 20kHz Gain range: - 15db ~ + 12 db(can be limited to +6db in the "evice Settings" of interface software),stepping is 0.1 db Band range: 0.011 ~3.595 Operating method 1: (panel can only set the gain) press "usic mode"...
7.3 Microphone Enhancement Feature Range: adjust range - 50% (off) ~ + 50 % Operating method 1: On the panel press the key "Music Enhance", set to continuously change enhance switch, turn the knob to adjust music inspired. Operating method 2: Operation from the interface software to set up MIC Enhance Panel Display...
7.8 microphone PEQ settings Balanced qty: 10 Type: parametric equalization filter (can be set to low / treble tone filter), graphic equalizer Frequency range: 20hz ~ 20khz Gain Range:-15db ~ +12 db (can be limited to +6db settings, setting from Device Settings "...
7.10 effect volume set Range: mute,-30db ~ 0db, Stepping: 0.5db Operation: set by "effect volume knob on the panel. " Operating method 2: by effect +", ffect on the remote control " " " Operating method 3: Operation from the interface software to set up Music Music Panel...
7.16 Echo mode, Echo thickness settings Range: Single, stereo, dual echo Range: On, Off Operation: Press the buttons "Effect Mode" on the panel continuously into the Echo Mode/ Echo Thickness, as shown below: MONO ECHO MODE ECHO TO REV Panel Display Keys "<"...
7.19 reverb type set Range: 1.off ; 2. Room ; 3 Small hall; 4.Hall; 5. Church; 6. Cathedral; 7. Vocal. Operation: Press the buttons "Effect Mode" on the panel continuously into the Reverb Type, as shown below: REV TYPE Room Panel Display Turning knob "music volume / Edit (press)"...
8.2 Direct sound to the main output, and the effect to the main output volume setting Range: Mute,-30db ~ 0db, Stepping: 0.5db Operation: Press the buttons "Main output Mode" on the panel continuously into the Direct sound to main output and Effect to the main output volume, as shown below: MIC DIR TO MAIN 5.0dB...
Keys "<" and ">" to switch the needed PEQ. Turning knob "music volume / edit (press) "to set Gain. Operating method 2: Operation from the interface software to set up(all equalizer parameter can be set ) Panel 8.5 Main output left delay, right-delay setting Range: 0.0ms ~ 5.0ms, stepping 0.1ms Operation method1: Press the buttons "Main output Mode"...
9 Center part operating instructions 9.1 Center volume setting Range: Mute, -3 0db ~ 0db, Stepping: 0.5db Operation method 1: Press the buttons "Center Mode" on the panel continuously into the Center volume , as shown below: CENT VOL 0.0dB CENT MAX VOL + 6.0dB Panel Display...
Keys "<" and ">" to switch Direct sound to the center and Effect to the center. Turning knob "usic volume / edit (press) "to set. Operating method 2: Operation from the interface software to set up Panel 9.4 Center PEQ settings The PEQ qty: 3 Type: parametric equalization filter (can be set to low / treble tone filter) and graphic equalizer.
10 The Sub woofer part operating instructions 10.1 Sub woofer volume and phase settings Volume range: mute,-30db ~ 0db, Stepping: 0.5db ° ° Phase range: 0 , 180 Operation method 1: Press the buttons "Sub Woofer Mode" on the panel continuously into the Sub woofer volume and phase, as shown below: SUB VOL 19.5dB...
10.3 Sub woofer PEQ settings PEQ qty : 3 Type: parametric equalization filter (can be set to low / treble tone filter) and graphic equalizer Frequency range: 20hz ~ 20khz Gain Range:-15db ~ +12 db, stepping 0.1db Bandwidth range: 0.011 to 3.595 Operation method 1: (Only can set EQ gain on the panel)Press the buttons "Sub Woofer Mode"...
10.5 Subwoofer compressor settings Threshold range: -20 ~ +16 db, stepping 0.5db Ratio: 2:1 4:1 8:1 16:1 32:1 64:1 128:1 Range: On, Off Operation method 1: (Only Threshold can be set )Press the buttons "Sub Mode" on the panel continuously into the Subwoofer compressor, as shown below: SUB COMP: THRES:...
11.3 program deleted (computer software interface features) 11.4 program data is saved to the computer (computer software interface features) 11.5 program import the data from the computer to the processor (computer software interface features) Turn-On to load the selected program. Connect the Processor unit to the computer ,open the software, set the program in"eboot effect"rom "evice setting"...
15 Subwoofer output options. Set this function under "Device Settings" in the software provided. when the mode is manual, the subwoofer volume setting does not change. when the mode is automatic: once the Microphone receives input signal, subwoofer output volume is the "concert" setting. if Microphone has no input signal, a certain time later , the subwoofer volume will switch to "ance"...
the wireless remote control The easy-to-use remote control function, eliminating the need for manual operation. Simple parameter adjustment makes you to adjust the parameter settings used easily as picture shown below. : Remote control keys function PRESET/USER Keys Function Adjust the feedback elimination Feedback eliminate Digit keys Press the digit keys to recall the memory directly...
22 When on-line computer interface software control the processor functions Online, the panel can not operate. COM Port Detect Automatically. Software can set all the parameters of the processor. Please refer to the corresponding HELP documentation software instruction. USB and RS232 cannot operate together. If RS232 interface is needed, please remove USB connection. 3 Important instruction on PC control Please read the following instruction carefully before doing the connection.