Miller skyline 90 Operator's Manual
  1. Manuals
  2. Brands
  3. Miller Manuals
  4. Camera Accessories
  5. skyline 90
  6. Operator's manual

Miller skyline 90 Operator's Manual

Fluid head
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
skyline
90
Fluid Head
OPERATOR'S
MANUAL
#1085 Skyline 90 Fluid Head

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the skyline 90 and is the answer not in the manual?

Questions and answers

Related Manuals for Miller skyline 90

Summary of Contents for Miller skyline 90

  • Page 1 Fluid Head OPERATOR’S MANUAL #1085 Skyline 90 Fluid Head...
  • Page 2 Introduction Thank you for purchasing the Skyline 90 Fluid Head. The Skyline 90 Fluid Head has been designed to suit payload capacities of EFP , OB and Studio camera systems up to 75 kg (165.4 lbs). The robust design and construction of the Skyline 90 Fluid...

  • Page 3: Features And Controls

    Features and Controls Camera Screws Wedge Base Plate Sliding Plate Wedge Plate Tilt Stopper Sliding Plate Lock Tilt Lock Pan Lock Carry Handle Assembly Mitchell Castle Nut Fig. 1...
  • Page 4 Features and Controls Wedge Plate Release Lever Sliding Plate Adjusting Knob Counterbalance Indicator Dial Counterbalance Control Knob TIlt Drag Knob Tilt Safety Lock Pan Drag Knob Mitchell Key Fig. 2...

  • Page 5: Safety Instructions

     Do not exceed the maximum payload capacity of the Fluid Please use this manual to familiarise yourself with the Head. operation of the Skyline 90 Fluid Head and observe these instructions to prevent any damage to your equipment.  Do not leave the camera unattended on the Fluid Head.

  • Page 6: Technical Data

    Technical Data Weight 23.0 kg (50.7 lbs) 350 (13.8") Payload Range 0 – 75 kg (0 – 165.4 lbs) Maximum Capacity 75.0 kg (165.4 lbs) Tilt Drag 15 Selectable fluid drag positions + 0 Tilt Range +60˚ / -60˚ Tilt Lock Positive lock brake system plus Tilt Safety Lock.

  • Page 7: Operating Instructions

    The operating instructions are described in three steps. Please read and understand these instructions before using this equipment. Do not omit any steps. The Skyline 90 Fluid Head can be mounted on a MITCHELL BASE only. 1 Fluid Head Set-up (Mitchell Base) 1.1 Ensure the Tripod, Jib, Pedestal etc.

  • Page 8: Camera Setup

    Sliding Plate Knob 2.5 Engage the WEDGE PLATE with the WEDGE BASE PLATE on SKYLINE 90 Head and lock off by returning the WEDGE PLATE RELEASE LEVER. Centre axis 2.6 Release the SLIDING PLATE LOCK and adjust the SLIDING PLATE (turn SLIDING PLATE KNOB) such that the camera’s...
  • Page 9 Operating Instructions 3 Counterbalance Control The counterbalance system was designed to neutralise the effect of the camera weight when it is tilted. The Skyline 90 Fluid Head offers a continuous counterbalance system which can be operated via the COUNTERBALANCE SELECTOR (fig.

  • Page 10: Maintenance And Storage

    Maintenance & Storage Warranty The Skyline 90 Fluid Head can be stored for extended periods; Please refer to warranty card for complete details, Miller recommends storage in a Miller Skyline 90 Head Case (#3348) and the following: Alternatively you can register your product via our warranty registration page.
  • Page 11 Miller Authorised Service Agents must carry out all service and repair work. Failure to observe this requirement may void warranty. It is advisable to notify Miller or a Miller Authorised Service Agent if a change of performance is observed as a result of dropping or rough usage.
  • Page 12 MILLER CAMERA SUPPORT EQUIPMENT 30 Hotham Parade Artarmon, Sydney NSW 2064 Australia Tel: +61 2 9439 6377 Fax: +61 2 9438 2819 D11409-1...

Table of Contents