Table of Contents
Advertisement
Menu List (Setup Screen)
Category
Setting item
VIDEO OUT
OUTPUT COLOR SPACE
OUTPUT DVI-D/HDMI
PREVIEW CONTRAST
PREVIEW SATURATION
PREVIEW BRIGHTNESS
PREVIEW COLOR SPACE
PREVIEW DVI-D/HDMI
OUTPUT FADE
OUTPUT FADE WHITE LEVEL 0–255
OUTPUT FADE BLACK LEVEL 0–255
OUTPUT FADE AUDIO FLW
AUDIO
AUTO MIXING SW
AUTO MIXING SETUP
ECHO CANCEL SW
ECHO CANCEL SETUP
AUDIO FOLLOW SW
AUDIO FOLLOW SETUP
Page 3/3
USER
The setting items are similar to those for "USER Button Settings" (p. 14).
MEMORY
SAVE
LOAD
MANUAL MODE
POWER ON LOAD
REMOTE
MIDI Rx CHANNEL
RS-232
BAUDRATE
GPI 1 TYPE
:
GPI 4 TYPE
GPO 1 TYPE
:
GPO 4 TYPE
SYSTEM
HDCP
FRAME RATE
SYSTEM FORMAT
4
Value
AUTO, RGB-FULL, RGB-LIMIT, YCbCr This sets the color space for HDMI OUT connector and RGB/COMPONENT output connector.
DVI-D, HDMI
-64–0–63
-64–0–63
-64–0–63
AUTO, RGB-FULL, RGB-LIMIT, YCbCr This sets the color space for PVW OUT connector.
DVI-D, HDMI
BLACK, WHITE, STILL
OFF, ON
OFF, ON
([EDIT])
OFF, ON
([EDIT])
OFF, ON
([EDIT])
([SETUP])
([SELECT])
OFF, ON
OFF, 1–8
1–16
OFF, ON
9600, 19200, 38400, 115200
N/A, VIDEO CH SEL 1–4,
MEMORY LOAD 1–8,
USER 1–5
ONE SHOT, ALT
OFF, ON
59.94 Hz, 50 Hz
720p, 1080i, 1080p
Explanation
This sets the output mode of the HDMI OUT connector.
This adjusts the contrast of the preview output video.
This adjusts the saturation of the preview output video.
This adjusts the brightness of the preview output video.
This sets the output mode for PVW OUT connector.
5 "BLACK" or "WHITE" specifies the fade color used during an output fade.
5 Setting this to "STILL" makes the [OUTPUT FADE] button function as a still-image output
button.
This adjusts the white level during output fade.
This adjusts the black level during output fade.
Setting this to "ON" enables the Audio Follow feature during output fade.
This switches the Auto Mixing feature on or off.
This displays the AUTO MIXING Screen (p. 6).
This switches the Echo Cancel feature on or off.
This displays the ECHO CANCEL Screen (p. 6).
This switches the Audio Follow feature on or off.
This displays the AUDIO FOLLOW Screen (p. 11).
This displays the MEMORY SELECT Screen (p. 7).
This displays the MEMORY LOAD Screen (p. 7).
This sets whether the state of the operation panel is updated (ON) or not updated (OFF)
when a memory is recalled.
Selecting a memory number causes the settings at the selected memory number to be
recalled at startup.
This sets the receive channel for MIDI messages when operating the VR-4HD remotely using
an external MIDI device.
Setting this to "ON" makes it possible to send and receive RS-232 commands.
This sets the communication speed (bps) of the RS-232 connector.
This sets the function assigned to the GPI channel.
N/A:
No function is assigned.
VIDEO CH SEL: This switches the video.
MEMORY LOAD: This loads a memory.
USER:
This performs the same operation as pressing the USER button.
* When a control signal is input from an external source, the assigned function is executed.
The GPI trigger is fixed at the trailing edge (low: ON).
For details, refer to "Inputting a Control Signal" (p. 22).
This sets the operation mode of the GPO channel.
ONE SHOT: This outputs a control signal for 1 second.
ALT:
This outputs a control signal using alternate operation.
* You can output a control signal by assigning a GPO channel (1–4) to a USER button, then
operating the USER button.
For details, refer to "Outputting a Control Signal" (p. 23).
When set to "ON, " copyright-protected (HDCP) video can be input. HDCP is also added to the
video that is output.
This sets the frame rate.
* For output via the USB 3.0 only, the frame rate when set to "59.94 Hz" is "29.97 Hz. "
Similarly, when set to "50 Hz, " the frame rate is "25 Hz. "
This specifies the system format for the VR-4HD. The input and output formats of the
respective connectors are determined according to the system format, as shown in the table
below.
Input format (*2)
System
Input connector:
format
HDMI IN 1–3
720p
720p
1080i
1080i, 1080p
1080p
1080i, 1080p
(*2) For the channel 4 input connectors (HDMI IN 4, RGB/COMPONENT 4, and COMPOSITE 4),
you set the input format individually using "RESOLUTION (EDID)" (p. 2), irrespective
of the system format.
(*3) For the HDMI OUT connector and the RGB/COMPONENT output connector, you can
specify a desired output format by using "OUTPUT RESOLUTION" (p. 3).
The system format setting is followed only when "OUTPUT RESOLUTION" is set to "AUTO. "
Output format
Output connector:
Output connector:
PVW OUT, HDMI OUT (*3),
USB 3.0
RGB/COMPONENT (*3)
720p
720p
1080i
1080p
1080p
Hide quick links:
Advertisement
Table of Contents
