1. Safety instructions 1. Read these instructions carefully. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this system near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Failure to do so may cause fast overheating and force system to switch itself off.
Additionaly, Fly line array is fully integrated with Powersoft® amplifiers, extending its functionality and convenience. Fly 6 is a line array module with fixed vertical curvature (20°). Closed enclosure with four 6” mid- range transducers and two 1,75” VC HF drivers is complete with integrated flying/stacking system and pole mount adapter.
Standard 5/8” shackle may be used to suspend the entire system. Attaching two Fly 6 systems - On the upper Fly 6 system release quick lock pins, pull the integrated link down, and secure it with the quick lock pin.
Page 8
- 0,5° - 4,5° Single, two or three Fly 6 cabinets are capable to be flown via FL-01 and FL-02 accessories. Table above states the angle between horizontal plane and vertical axis of the top-most cabinet. Positive angle means cabinets are “looking up“, negative angle means cabinets are “looking down“.
Page 9
4.1. System operation - Rigging Fly Sub 12 system flying via flying adapter Required accessories: FL-01 (part No. 0200101101) - 2 pcs FL-04 (part No. 0200101102) - 1 pcs VA-0010 (part No. 0209000001) - 4 pcs - Release quick locking pins on the top of the Fly Sub 12.
Page 10
- Mount securely the SAT-3T distance pole into the M20 socket of the Fly Sub 15 or Fly Sub 18 subwoofer. - Mount the Fly 6 + FL-01 + FL-03 assembly onto the SAT-3T distance pole. MAXIMUM OF TWO FLY 6 SYTEMS ARE ALLOWED FOR POLE MOUNTING.
4.2. System operation - amplifiers Fly 6 and Fly Sub 12 Fly Sub 15 and Fly Sub 18 built-in power amplifier: built-in power amplifier: LIMIT PRESET1 LIMIT PRESET1 TEMP PRESET2 TEMP PRESET2 SIGNAL PRESET3 SIGNAL PRESET3 READY PRESET4 READY PRESET4...
Fly Array systems are equipped with PowerCon B mains power outlets for mains link to additional Fly system. For linking several Fly 6 full-range systems CN-0011 PowerCon link cable may be used. (Part number 0204000004, not supplied with the system).
Fly 6 configurations. Fly 6 full-range speaker systems should be set up differently while using different number of units in stack. For this purpose, different presets on all speaker in the stack should be used: 2x Fly 6...
Page 14
Fly Sub 12 Fly Sub 12 Fly Sub 12 Fly Sub 12 (inv) (inv) PRESET 1 PRESET 3 PRESET 2 PRESET 4 Fly 6 Fly 6 Fly Sub 12 Fly Sub 12 Stack Stack PRESET 1 PRESET 3 Fly 6 Fly 6...
System Fly 6 Fly Sub 12 Fly Sub 15 Fly Sub 18 1 pcs - Fly 6 - 1 pcs - Fly Sub 12 1 pcs - Fly Sub 15 1 pcs - Fly Sub 18 powered fixed array - powered array...
Page 16
MANUFACTURER’S WARRANTY 1. By this warranty MAG Audio grants that all equipment manufactured under the MAG Audio trademark is free from defects in material, components and factory workmanship under the normal use and maintenance for the time as specified below.
Need help?
Do you have a question about the Fly 6 and is the answer not in the manual?
Questions and answers