JVC DR-MV2SEU Service Manual page 18

3.2 DISASSEMBLY/ASSEMBLY PROCEDURES OF DECK MECHANISM
Before following the procedures described below, be sure to remove the deck assembly from the cabinet. (Refer to CABINET DISAS-
SEMBLY INSTRUCTIONS.)
All the following procedures, including those for adjustment and replacement of parts, should be done in Eject mode; see the positions
of [44] and [45] in Fig.1 on page 1-20. When reassembling, follow the steps in reverse order.
STEP/ STARTING PART
LOC. No. No.
[1] [1] Guide Holder A
[2] [1] Cassette Holder Assembly
[3] [2] Slider (SP)
[4] [2] Slider (TU)
[5] [4] Lock Lever
[6] [2] Cassette Plate
[7] [7] Cylinder Assembly
[8] [8] Loading Motor Assembly
[9] [9] ACE Head Assembly
[10] [2] Tape Guide Arm Assembly
[11] [10] C Door Opener
[12] [11] Pinch Arm (B)
[13] [12] Pinch Arm (A) Assembly
[14] [14] FE Head
[15] [15] Prism
[16] [2] Slider Shaft
[17] [16] C Drive Lever (SP)
[18] [16] C Drive Lever (TU)
[19] [19] Capstan Motor
[20] [20] Clutch Assembly (HI)
[21] [20] Center Gear
*[22] [22] F Brake Assembly (HI)
[23] [22] Worm Holder
[24] [22] Pulley Assembly (HI)
[25] [25] Mode Gear (LM)
[26] [20],[25] Mode Lever (HI)
[27] [22],[23],[26] Cam Gear (A) (HI)
[28] [26] TR Gear C
[29] [28] TR Gear Spring
[30] [29] TR Gear A/B
[31] [31] FF Arm (HI)
[32] [26] Idler Assembly (HI)
[33] [26] BT Arm
[34] [26] Loading Arm (SP)Assembly
[35] [34] Loading Arm (TU) Assembly
[36] [16],[26] M Brake (TU) Assembly (HI)
[37] [2],[26] M Brake (SP)Assembly (HI)
1-18 (No.YD087)
REMOVAL
Fig. No. REMOVE/*UNHOOK/
UNLOCK/RELEASE/
UNPLUG/DESOLDER
T 3 2(S-1)
T 4
T 5 (S-1A), *(L-1)
T 5 *(L-2)
T 5 *(L-3), *(P-1)
T 5
T 1,6 Desolder, 3(S-2)
T 1,7 Desolder, LDG Belt, 2(S-3)
T 1,7 (S-4)
T 1,8 *(P-2)
T 1,8 (S-4A), *(L-4)
T 1,8,9 *(P-3)
T 1,8,9
T 1,10 (S-5)
T 1,10 (S-6)
T 11 *(L-5)
T 11
T 11 (S-7), *(P-4)
B 2,12 3(S-8), Cap Belt
B 2,13 (C-1)
B 13
B 2,13 *(L-6)
B 2,14 (S-9), *(L-7), *(L-8)
B 2,14
B 2,14 (C-2)
B 2,14,15 (C-3)
B 2,14,15 (C-4)
B 2,14 (C-5)
B 14
B 14
B 1,16
B 1,16 *(L-9)
B 2,16 *(P-5)
B 2,16
B 2,16
T 1,17
T 1,17 *(P-6)
INSTALLATION
ADJUSTMENT
CONDITION
(+)Refer to Alignment
Sec.Page 1-41
(+)Refer to Alignment
Sec.Page 1-41
(+)Refer to Alignment
Sec.Page 1-41