Specific Unit Information - Coleman PxXU-V series Installation Instructions Manual

035-17468-001 Rev. A (801)
VENT SAFETY CHECK PROCEDURE
This furnace may not be common vented with any
other appliance, since it requires separate, properly-
sized vent lines. The furnace shall not be connected
to any type of B, BW or L vent or vent connector,
and not connected to any portion of a factory-built or
masonry chimney.
If this furnace is replacing a common-vented fur-
nace, it may be necessary to resize the existing vent
line and chimney to prevent oversizing problems for
the new combination of units. Refer to the National
Gas Code (ANSI Z223.1) or CAN/CGA B149.1 or.2
Installation Code (latest editions).
The following steps shall be followed with each appliance
connected to the venting system placed in operation, while
any other appliances connected to the venting system are not
in operation:
1. Seal any unused openings in the venting system.
2. Inspect the venting system for proper size and horizontal
pitch, as required in the National Fuel Gas Code, ANSI
Z223.1, or the CAN/CGA B149 Installation Codes and
these instructions. Determine that there is no blockage
or restriction, leakage, corrosion or other deficiencies
which could cause an unsafe condition.
3. Insofar as is practical, close all building doors and win-
dows and all doors between the space in which the appli-
ance(s) is located and other spaces of the building. Turn
on clothes dryers. Turn on any exhaust fans, such as
range hoods and bathroom exhausts, so they shall oper-
ate at maximum speed. Do not operate a summer
exhaust fan. Close fireplace dampers.
4. Follow the lighting instructions. Place the appliance
being inspected in operation. Adjust thermostat so the
appliance shall operate continuously.
5. Test for draft hood equipped appliance spillage at the
draft hood relief opening after 5 minutes of main burner
operation. Use the flame of a match or candle.
6. After it has been determined that each appliance con-
nected to the venting system properly vents when tested
as outlined above, return doors, windows, exhaust fans,
fireplace dampers and any other gas burning appliance
to their previous conditions of use.
7. If improper venting is observed during any of the above
tests, the venting system must be corrected.
8. Any corrections to the common venting system must be
in accordance with the National Fuel Gas Code Z223.1
or CAN/CGA B149.1 or.2 Installation Code (latest edi-
tions). If the common vent system must be resized, it
should be resized to approach the minimum size as
determined using the appropriate tables in Appendix G
of the above codes.
Unitary Products Group

SPECIFIC UNIT INFORMATION

LIMITATIONS & LOCATION
This furnace should be installed in accordance with all
national and local building/safety codes and requirements, or
in the absence of local codes, with the National Fuel Gas
Code ANSI Z223.1 or CAN/CGA B149.1 or .2 Installation
Code (latest editions), local plumbing or waste water codes,
and other applicable codes.
CLEARANCES FOR ACCESS
Ample clearances should be provided to permit easy access
to the unit. The following minimum clearances are recom-
mended:
1. Twenty-four (24) inches between the front of the furnace
and an adjacent wall or another appliance, when access
is required for servicing and cleaning.
2. Eighteen (18) inches at the side where access is
required for passage to the front when servicing or for
inspection or replacement of flue/vent connections.
NOTE: In all cases, accessibility clearances shall take prece-
dence over clearances for combustible materials where
accessibility clearances are greater.
Do not install the furnace in an unconditioned space
or garage that could experience ambient tempera-
tures of 32° F (0° C) or lower. For application in
below freezing locations, See "BELOW FREEZING
LOCATIONS" on page 4.
The furnace is not to be used for temporary heating
of buildings or structures under construction.
This unit must be installed in a level (1/4") position
side-to-side and front-to-back to provide proper con-
densate drainage.
Do not allow return air temperature to be below 55°F
for extended periods. To do so may cause conden-
sation to occur in the maim fired heat exchanger.
Only use natural gas in furnaces designed for natu-
ral gas. Only use propane (LP) gas for furnaces that
have been properly converted to use propane (LP)
gas. Do not use this furnace with butane. Using
wrong gas could create a hazard, resulting in dam-
age, injury or death.
3