Summary of Contents for TDR VMI QUICKSAND
- Page 1 What’s In This User Guide? Getting started - sanding a disc right now Getting to know your machine and how it works Changing the consumbles and other operations Maintenance and other useful information...
-
Page 2: Getting Started
User Guide Contents Page 1 Page 5 Page 9 Getting Started How to use your machine Additional Information Unpacking your Machine Modes of Operation Repackaging The Parts of the Machine Notifications Frequent Questions Page 2 Page 6 Page 10 Initial Setup Care and Maintenance Additional Information Replacing Sanding Pads... - Page 3 Turntable Catch Assembly Tray 4. Remove the Left and the Right side packing foams. 5. Take the VMI Quicksand out of Keypad the protective plastic bag. Chip Port 6. Position the machine on a sturdy flat surface with...
-
Page 4: Powering Up The Machine
Page 2 Initial Setup Installing the Credit Chip Understanding the Consumables Take the Credit Chip provided with your machine, and install it into You will receive starter consumables in the box for 50 minutes: the Chip Port. The Quicksand unit will recognize this chip once the machine is 2 x Foam Pads powered on. - Page 5 Then re-install the Lid Stopper. To install them, simply push them on to each nozzle. They are to be replaced with every new consumables Your VMI Quicksand unit is pack. now ready to be used!
-
Page 6: How To Use Your Machine
How to use your machine Page 4 General Operation 1. Place disc onto the Turntable Assembly, with the label side facing down! Warning: Do not attempt to repair 1. Switch the machine on: the front lights Blu-ray Discs in this machine, they will and display will light up and the lid will get damaged beyond repair. -
Page 7: Modes Of Operation
Regular: 10 Seconds The Credit Chip has been designed to monitor the consumables used within your VMI Quicksand, to ensure that each disc is repaired to the same standard, and to 1. Press the “Regular” button decrease any downtime that may result from not having replacement consumables... -
Page 8: Care And Maintenance
Care and Maintenance Page 6 5. Locate the Water Reservoir and the opening Replacing Sanding Pads for the filter. Pull the filter out of the reservoir. The machine will notify the Operator to 6. Rinse the filter under warm water until all replace the Sanding Pads by displaying the of the plastic remnants are washed away. - Page 9 Care and Maintenance Page 7 Cleaning Water Reservoir (Do not fill past the ‘MAX’ fill line) It is important that you clean out and refill the 15. Re-install the Turntable. Water Reservoir at both the “CW” and “RC” 16. Re-install the Lid Stopper. messages.
- Page 10 Page 8 Care and Maintenance Cleaning the Catch Tray Replacing Jet Nozzle Extenders Over time your Catch Tray may build up with plastic residue from the Sanding Process. There 1. Pull off the existing Jet Nozzle Extenders is no set time for when this item needs to be and discard.
-
Page 11: Frequent Questions
Why do I have to remove the Water from the machine for shipping? Since we cannot control how your VMI Quicksand is handled when in transit, we ask that you 9. Place the Quicksand into the Shipping Box. -
Page 12: Specifications
Additional Information Page 10 Specifications Contacting Us totaldiscrepair.co.uk/support/vmi-quicksand Disconnect unit from supply circuit before opening! 0800 412 5424 Warning and Cautions: You are cautioned that any changes or modifications not expressively approved in this manual could void your warranty. Total Disc Repair, Unit 1, Christchurch Business Park, Radar Way, If you have any questions about this product, contact us on 01202 489 500. -
Page 13: Disc Types
Disc Types Page 11 DVDs Blu-rays With the invention of High Definition (HD) there was When discs were invented the process of The early CDs were mainly used for audio and so a need to carry more information on a disc and soon construction was quite simple. - Page 14 Page 12...