1. Manuals
  2. Brands
  3. Borg & Overstrom Manuals
  4. Dispenser
  5. b5
  6. Quick start manual

Borg & Overstrom b5 Quick Start Manual

Hide thumbs Also See for b5:
Table of Contents

Advertisement

Quick Links

Quick Start Guide
Chilled
Ambient
Contents
Page No
Page No
Description
Description
2
3
4
5
Cold Water Connection & Operation
7
8
9
11
12
13
Dispense Options
Chilled & Ambient
Chilled, Ambient & Sparkling
Chilled, Ambient & Hot
Chilled, Hot & Sparkling
GB

Advertisement

Table of Contents
loading

Related Manuals for Borg & Overstrom b5

Summary of Contents for Borg & Overstrom b5

  • Page 1: Table Of Contents

    Quick Start Guide Dispense Options Chilled & Ambient Chilled, Ambient & Sparkling Chilled, Ambient & Hot Chilled Ambient Chilled, Hot & Sparkling Contents Page No Page No Description Description Major Components Water & CO2 Connection CO2 Bottle Installation Level Sensor Assembly Cold Water Connection &...

  • Page 2: Major Components

    Installation Major Components Left Table Water Tap Set Plate Handle Drip Tray Right Table Plate IC Control Board Cold Tank Leak Detector Reset Level Sensor Water & CO2 Connection Hot Power Switch Drain Port Carbonation Switch Chilled Switch IEC Power Socket Inlet Water (1/4”) CO2 Connector (1/4”) ©...

  • Page 3: Co2 Bottle Installation

    CO2 Bottle Installation (Sparkling Versions Only) IMPORTANT! ALWAYS ENSURE SECURITY CLIPS ARE USED ON ALL WATER AND CO2 CONNECTIONS. Attach the regulator to the After completing the water disposable CO2 bottle, ensuring installation, turn on the soda the regulator is closed. Connect power switch and the pump will the CO2 bottle and regulator run.

  • Page 4: Level Sensor Assembly

    Level Sensor Assembly Check all parts are present. Locate and connect the drainage tubing into the top of the level sensor connector. The LED lighting at the base of the Empty the waste container to cancel. faucet will flash slowly for 1 minute. This is also repeataed every time a dispense button is pressed.
  • Page 5 Operation Water Connection & Operation Connect and turn on the water Plug in the power supply, supply. cold, hot & sparkling tanks will automatically fill. Activate the carbonation & hot Activate cold power switch. power switch (if present). Borg & Overström Quick Start Guide...
  • Page 6 Water Connection & Operation (Continued) cold heating chilling Flush through 10 litres of water When the cold water switch is before use. turned on, the cold water and chilling LED will be on. 10 c cold cold heating heating chilling chilling The temperature of cold water When the heating LED is off the...

  • Page 7: Functions & Controls

    Functions & Controls Hot Water Lock Button cold heating chilling Sparkling Water Button (selected models) Hot Water Button Cold Water Button Ambient Water Button General Safety • Leave a space no less than 15cm between the wall and dispenser. • Keep the machine away from sunlight, heat and moisture.

  • Page 8: Isolation & Removal

    Maintenance & Cleaning Isolation & Removal Please make sure the machine Turn off the water supply. is completely disconnected from electricity before carrying out any maintenance work. Cold water drain To drain the Direct Chill tank, remove the cap on the back of the machine. We recommend it is refitted immediately upon draining being completed.

  • Page 9: Sanitisation Guide

    Sanitisation Guide NOTE: Before beginning the sanitation process please ensure that water is turned off at the mains and refer to the MSDS document for further information. Use bioguard hand gel and ensure gloves are worn. cold heating chilling Add 25 ml of Bioguard Briefly press cold/ambient dispense button to release Internal Sanitisation fluid to a...
  • Page 10 Sanitisation Guide (continued) When the external cleaning Remember to include the (minimum 5 minutes) is drip tray. Empty the Waste completed, flush the machine Overflow system and flush using the cold button with through with a small amount of clean water until the dispense sanitisation fluid if needed.

  • Page 11: Leak Dectection

    Leak Detection NOTE: This machine is equipped with a leakage detection device. When leaking is detected, the dispense operation will be cut off automatically. This is indicated by a blue LED flashing at the base of the tap. To reset: Unplug the machine and remove Locate the leak and rectify.

  • Page 12: Emptying The Carbonation Tank

    Emptying the Carbonation Tank cold heating chilling Switch off the Carbonation Press and hold the Sparkling System switch on the back of water dispense button until all the unit. water is expelled The tank is empty of sparking Ensure to release the Sparkling water when only CO2 is being water button and take care to released.

  • Page 13: Troubleshooting

    Troubleshooting Fault Diagnosis: Water Dispensing Issues Problem/Report Possible Cause Suggested Action No Water From Water Supply turned off. Check all Taps/valves/ filters on Ambient Valve incoming supply are fitted and are turned on. No Electricity/Power Check power cord connected and Supply.
  • Page 14 Water Dispensing Issues Continued Problem/Report Possible Cause Suggested Action Cold Water not Cold Fan not working. Check and replace, as required. Hot Water not Hot Heating cycle incomplete. Wait for heating LED to stop showing. High hot water usage. Advise user/s. Hot thermostat not working.
  • Page 15 Fault Diagnosis: Miscellaneous Problem/Report Possible Cause Suggested Action No LED Control Lights No electricity to Machine. Check power supply and reconnect as necessary. Check Fuse in IEC Socket. Replace if necessary. Control PCB not working. Check and replace PCB as necessary.
  • Page 16 Borg & Overström Quick Start Guide...

Table of Contents