Table of Contents
Advertisement
Model 1317A
Changes and Options
SECTION VII
MANUAL CHANGES AND OPTIONS
7-1.
INTRODUCTION.
7-2. This section contains information required to
backdate or update this manual for a specific in-
strument.
Description of special options and standard
options are also in this section.
7-3.
MANUAL CHANGES.
7-4. This manual applies directly to instruments
having the same serial prefix shown on the manual
title page. If the serial prefix of the instrument is not
the same as the one on the title page, find your serial
prefix in table 7-1 and make the changes to the
manual that are listed for that serial prefix. When
making changes listed in table 7-1, make the change
with the highest number first. Example: if backdating
changes 1, 2, and 3 are required for your serial prefix,
do change 3 first, then change 2, and finally change 1.
If the serial prefix of the instrument is not listed
either in the title page or in table 7-1, refer to the
enclosed
replacement pages
in
the front of this manual.
Table 7-1. Manual Changes
Serial Prefix
Make Changes
1406A
3, 2, 1
1510A
3, 2
1542A
3
7-5.
STANDARD OPTIONS.
7-6. Standard options are modifications installed
on HP instruments at the factory and are available on
request. Contact the nearest Hewlett-Packard Sales/
Service Office for information concerning standard
options. Table 7-2 lists the Model 1317 A standard
options.
7-7.
INSTRUMENT IMPROVEMENT MOD-
IFICATIONS.
7-8. The following modifications may be easily
installed by the customer to adapt the Model 1317 A
for a wide variety of applications. Single-ended or
differential X- and Y-axis amplifiers and attenuators
for X-, Y-, and Z-axis amplifiers are briefly de-
scribed in the following paragraphs. Refer to HP
Application Note 166 (included with the instrument)
for a full discussion and installation instructions
before making any modifications. Figures 7-2 through
7-5 are for use with Application Note 166.
NOTE
Modifications are not the same as changes
required to make this manual apply di-
rectly to the instrument as it left the
factory.
7-9.
SINGLE-ENDED OR DIFFERENTIAL X-AXIS AND
V-AXIS AMPLIFIERS.
The 1317A is configured with
X-axis and Y-axis amplifiers operating differentially.
However, these amplifiers may be modified to any
configuration
from
single-ended
(with
shield
grounded), to fully differential with balanced imped-
ance and voltage sensitivity, or anything in between.
7-10.
X-AXIS, V-AXIS AND Z-AXIS ATTENUATORS.
The 1317 A provides full-scale X-axis and Y-axis
deflection when a 1 V peak-to-peak signal is applied
to either input. A front-panel GAIN control for each
axis reduces sensitivity to 1.75 V peak-to-peak for full
screen deflection. Attenuators may be added to pro-
vide full-scale deflection for any required voltage
~1
V on either axis. Regardless of signal input at-
tenuation, range of the GAIN control is constant at a
ratio of 1.75:1. The Z-axis attenuator may be modified
to accommodate Z-axis input voltages greater than
2.5 V, or to allow an increased range of the Z-axis
Balance adjustment (referenced to the input signal
level). Internal Z-axis Gain adjustment range remains
constant at a ratio of 2.5:1 regardless of input signal
attenuation.
CHANGE 1
Table 6-2,
Add: DS1: HP Part No. 1450-0419; LIGHT, IND,
NEON, WHT TL LENS; Mfr Code 72765; Mfr Part
No. 599-237-WHITE.
MP13: Change HP Part No. and Mfr Part No. to
01317-00101.
MP14: Change HP Part No. and Mfr Part No. to
01317-00204.
MP18: Change HP Part No. and Mfr Part No. to
01321-04104.
Add: MP18 OPTION 050 through MP18 OPTION
054: HP Part No. 01317-04107; Qty 1; PLATE:
INPUT RIGHT; Mfr Code 28480; Mfr Part No.
01317-04107.
MP36 OPTION 055: Change to HP Part No. 1490-
0922; Qty 2; RACK SLIDES; Mfr Code 28480; Mfr
Part No. 1490-0922.
7-1
Advertisement
Table of Contents
Troubleshooting
