1. Manuals
  2. Brands
  3. UEi Manuals
  4. Measuring Instruments
  5. ACM6000
  6. Instruction manual

UEi ACM6000 Instruction Manual

Low amp clamp-on dmm
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
ACM6000
1-800-547-5740 • Fax: (503) 643-6322
www.ueiautomotive.com • email: info@ueiautomotive.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ACM6000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for UEi ACM6000

Summary of Contents for UEi ACM6000

  • Page 1 INSTRUCTION MANUAL ACM6000 1-800-547-5740 • Fax: (503) 643-6322 www.ueiautomotive.com • email: info@ueiautomotive.com...

  • Page 2: International Symbols

    • Even moderate amounts of current can cause ventricular fibrillation • Use insulated tools and gloves to avoid electrical shock • Disconnect wiring from supply voltage before performing The ACM6000 DC/AC Clamp Meter instrument allows pocket sized continuity tests convenience for testing voltage, current flow, resistance, continuity •...
  • Page 3 (amperage) is also tested. near the test area. The ACM6000 can be used to test for both AC and DC current. The user selectable range switch allows for measurement up to 200 Amps. Data hold •...

  • Page 4: Operating Instructions

    Pouch B. Plug the red lead into the V ˚F input A pouch is provided for storage of the ACM6000 Clamp Meter, the 4. Connect the probe tips to the circuit under test. For automotive accessories and the operator’s manual.
  • Page 5 OFF. 4. Verify that the vehicle ignition switch is in the OFF position. 5. Place the jaws of the ACM6000 around the starter cable and be sure the jaws are closed. Plug the standard K-type 6.
  • Page 6 8. Because the display readout can vary up to 60mA, add 60mA to the highest expected reading for parasitic load of the vehicle 6. Place the jaws of the ACM6000 around one of the two wires, under test. If the display readout exceeds that amount, further either one will work.
  • Page 7 Diagnosing fuel pump problems can sometimes be difficult. The include: The ABS Sensor, the Magnetic Crank Sensor, Magnetic ACM6000 can be used to make a quick check for fuel pump current Distributor Pickup, and the Alternator. These devices operate at speeds draw during cranking.
  • Page 8 4. Turn the ACM6000 rotary function switch to Use the DMM DC Voltage Testing capability of the ACM6000 to make 5. Connect the test leads to the meter. these important voltage tests.
  • Page 9 TIP: Low Voltage - Check connections, drive belt, faulty voltage re gu l a t o r. Ohms and audible continuity measurements: High Voltage - Usually indicates a faulty voltage re gu l a t o r. 1. Slide the ACM6000 power switch to the ON position. Potentiometer tests 2. Turn the rotary function switch to...

  • Page 10: Specifications

    If the humidity raises to the point of causing condensation on the ACM6000, the meter can become dangerous to use and can give erroneous readings. Most test equipment in use today use sensitive digital electrical components.
  • Page 11 11.5” leads ....... . .ADL7100A108 Premium silicon test leads ..... . .ATL300 ACM6000-MAN P. 10...

  • Page 12: Limited Warranty

    Low Amp Clamp-On DMM Limited Warranty The ACM6000 is warranted to be free from defects in materials and workmanship for a period of one year from the date of purchase. If within the warra n ty period your instrument should become inoperative from such defects, the unit will be repaired or replaced at UEi’s option.

This manual is also suitable for:

Pac45

Table of Contents