Download Print this page

Whittier Wood 1614AUF Assembly Instructions Manual

Alder hutch

Advertisement

Quick Links

McKenzie Alder
Hutch
Ready to Finish
Assembly Instructions
Model #
1614AUF
McKenzie Alder
Hutch 24"W
1626AUF
McKenzie Alder
Hutch 36"W
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
1620AUF
McKenzie Alder
Hutch 30"W
1632AUF
McKenzie Alder
Hutch 48"W
CUSTOMER SERVICE
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Fax: 541-687-2060• Email: info@whittierwood.com
P.O. Box 2827
Eugene, OR 97402 USA
IMPORTANT NOTES:
• For normal household use only. Not recommended for commercial use.
• Do not climb, sit or stand on this piece of furniture.
• Do not overload the shelves.
• Unload items before you move this unit.
• Before you begin your project, completely read the Assembly
Instructions and Finishing Hints.
• This assembly requires two people.
Serious or fatal crushing injuries can occur from furniture tip-over. Use of
tip-over restraints may only reduce but not eliminate the risk of tip-over.
To help prevent tip-over:
Place heaviest items in the bottom drawers.
Unless specifically designed to accommodate, do not set TVs or other
heavy objects on top of this product.
Never allow children to climb or hang on drawers, doors or shelves.
Never open more than one drawer at a time.
Do not defeat or remove the drawer interlock system.
Warning: At least one tipping restraint kit was included with your piece of
Whittier Wood Furniture. When you receive your furniture, be sure to find
and properly install the tipping restraint(s). If you cannot locate the
restraint(s), please contact us immediately for replacement.
Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the state of California to cause cancer.
Avoid inhaling wood dust or use a dust mask or other safeguards for
personal protection.
For more information go to: www.p65warnings.ca.gov/wood
This product can expose you to chemicals, including formaldehyde,
which are known to the State of California to cause cancer.
For more information go to: www.p65warnings.ca.gov/furniture
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
Production Code:
WARNING
04/17

Advertisement

loading
Need help?

Need help?

Do you have a question about the 1614AUF and is the answer not in the manual?

Questions and answers

Summary of Contents for Whittier Wood 1614AUF

  • Page 1 If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you cannot order replacement parts through your dealer, please contact our customer service department.
  • Page 2 1614AUF; 1620AUF; 1626AUF & 1632AUF McKenzie Alder Hutch Parts List Please identify the parts and check that quantities received match those on this list. If you need to replace a part, refer to the following letter and part name. Quantity...
  • Page 3 1614AUF; 1620AUF; 1626AUF & 1632AUF McKenzie Alder Hutch Assembly Instructions Tools Required: Phillips Screwdriver, Pencil, Rubber mallet or Padded hammer. To install the adjustable shelves: Determine where you want to place the Adjustable Shelves (C). Insert the Shelf Brackets (Q) flat side down into the four different holes and install the shelf.
  • Page 4 1614AUF; 1620AUF; 1626AUF & 1632AUF McKenzie Alder Hutch Assembly Instructions Place the Hutch face-up on a clean, protected surface. Peel the backing tape off one of the Pads Strip (M) and place it on the bottom of the left side of the Case Assembly. Repeat for the right side and for the 1632 on the Vertical Divider.
  • Page 5 1614AUF; 1620AUF; 1626AUF & 1632AUF McKenzie Alder Hutch Assembly Instructions It is important you secure your Hutch to your Cabinet. Place the Hutch on top of the McKenzie Alder Cabinet and line it up with the back and sides. Find the Lock Plates (N) attached at each side of the Hutch near the bottom edge and remove the innermost screw (I) from each.
  • Page 6 Before you begin this assembly, identify each part and make sure the quantities received match what is on this list. If you need to replace a part, contact Whittier Wood Furniture customer service and refer to the following list for its name and letter code.
  • Page 7 1614AUF; 1620AUF; 1626AUF & 1632AUF McKenzie Alder Hutch Assembly Instructions Decide where you want to place the bookcase in your room. Mark the baseboard with a pencil mark directly behind the location where the tipping restraint is attached to your item. Move the item away from the wall far enough to allow you to access the spot where the baseboard meets the floor.
  • Page 8 1614AUF; 1620AUF; 1626AUF & 1632AUF McKenzie Alder Hutch Assembly Instructions Move the item back into position against the wall and reach underneath the bookcase to grasp the loop in the free end of the strap. Pull the free end of the strap until portion between the Cam Buckle (A) and the bottom of the item is tight.
  • Page 9 1614AUF; 1620AUF; 1626AUF & 1632AUF McKenzie Alder Hutch Assembly Instructions RAFIX ATTACHEMENT SYSTEM 1. Insert the Rafix Bolt into the shelf 3. Slide the Rafix Cam over the Rafix Bolt. so that the shoulder is flush with the surface of the wood.
  • Page 10 Whittier Finishing Hints instructions call for a slow drying glue. Carefully read the Checklist of materials □ □ □ label and instructions of the glue manufacturer. Your unit Rubber gloves Tack cloth #220 & #320 may not need glue. □ □...
  • Page 11: Preparing The Surface

    Whittier Finishing Hints Preparing the surface apply additional coats. Lightly sand and wipe surface with a lint-free rag or tack cloth between coats. Sand each piece with #220 grit sandpaper. Sand with the grain of the wood on flat surfaces and opposite the Some finishes tend to slightly raise the grain.

This manual is also suitable for:

1626auf1620auf1632auf