Contents SPI H D141 ........................ 1 ANDHELD METER GENERAL INFORMATION ......................1 1. INTRODUCTION ........................2 2. FUNCTION AND OPERATION ..................... 3 3. USE OF HANDHELD METER ......................4 4. SPARE PARTS ..........................5 5. TO START ..........................6 6. PREPARATION CHEMICALS......................7 7.
SPI HSPI General information The SPI handheld meter is specifically designed to carry out measurements in the field. With the design there is aimed at a good price/quality ratio for this unit This handheld meter can be used to measure the following parameters: ...
SPI – D141 HANDHELD METER SPI HSPI 1. Introduction Thank you for buying this handheld meter. This manual is made to help you by installation and use of your handheld meter. We advise to read this manual with care. You bought our new handheld meter this handheld meter can be used to measure the following parameters: ...
SPI – D141 HANDHELD METER SPI HSPI 2. Function and operation 2.1 Warnings • This handheld meter is not waterproof, so by usage take care of water in the handheld meter. Let the handheld meter not left in water. Water can cause damage onto the electronic circuits.
SPI – D141 HANDHELD METER SPI HSPI 3. Use of handheld meter 3.1 Handheld meter description: 1 DISPLAY 2 ON/OFF 3 CALIB. 4 ENTER 5 MENU 6 CHANNEL 1 7 CHANNEL 2 Parts of the handheld meter : Display. On/Off.
SPI – D141 HANDHELD METER SPI HSPI 4. Spare parts This handheld meter is delivered include: • 1 x hand case • 2 x Caps • 4 x Cuvettes • 100 ml Phenol red with pipette • 1 x graduated cylinder •...
SPI – D141 HANDHELD METER SPI HSPI 5. To start 5.1 Demand of surrounding: During measurement the results can have bad influence of light so you use 2 caps to cover the cuvettes during measurement. 5.2 Installation: Take the handheld meter out of case and check the cuvettes.
SPI – D141 HANDHELD METER SPI HSPI 6. Preparation chemicals 6.1 DPD 1: DPD 1 is ready to use solution. 6.2 Start: Start is a ready to use solution. 6.3 Totaal 2: Totaal 2 is a ready to use solution ...
SPI – D141 HANDHELD METER SPI HSPI 7. Use 7.1 Zero calibration: • Before every measurement a zero calibration has to be done. • You take 2 empty, clean cuvettes (Glass test tubes) with the appropriate colour line and rinse off with the measured water.
Page 12
SPI – D141 HANDHELD METER SPI HSPI After finishing all measurements for total chlorine, the cuvettes has to be cleaned properly. 7.4 pH (Cuvette with blue line): After zero calibration you can continue your sample measurement. The cuvette for blanc measurement is left in channel 1 (Reference).
Page 13
SPI – D141 HANDHELD METER SPI HSPI 7.5 Hydrogen peroxide (Cuvette with blue line): After zero calibration you can continue your sample measurement. The cuvette for blanc measurement is left in channel 2 (Reference). Rinse the cuvette with the blue line with the measured water.
SPI – D141 HANDHELD METER SPI HSPI 8. Safety regards All delivered chemicals can cause health injures so take care handling those chemicals. R/36/37/38 Irritating for eyes, respiratory organs and skin Keep out of reach from children. ...
SPI – D141 HANDHELD METER SPI HSPI 9. Maintenance 9.1 Routine maintenance: Take successively following actions: Clean cuvettes properly Clean channels with a dry soft tissue. 10. Storage and transport 10.1 Dismantle: Replace the handheld meter into original hand case get the cuvettes out of handheld meter, take care there is no water left in handheld meter.
Need help?
Do you have a question about the D141 and is the answer not in the manual?
Questions and answers