Sharp AL-1611 Service Manual page 82

PIN No. Signal Name IN/OUT
93 /FAXREQ OUT
94 /FAXACK IN
95 3.3V Power
96 /FAXCS IN
97 /ESPRD IN
98 GND Power
99 /ESREQ OUT
100 /ESACK IN
101 /ESCS IN
102 PARAD0 IN/OUT
103 PARAD1 IN/OUT
104 PARAD2 IN/OUT
105 PARAD3 IN/OUT
106 PARAD4 IN/OUT
107 PARAD5 IN/OUT
108 5V Power
109 PARAD6 IN/OUT
110 PARAD7 IN/OUT
111 GND Power
112 /REV OUT
113 INIT IN
114 /SLCTIN IN
115 /AUTOFD IN
116 /STB IN
117 /ACK OUT
118 BUSY OUT
119 PE OUT
120 /FAULT OUT
121 5V Power
122 SLCT OUT
123 /TESTPIN0 IN
124 GND Power
125 PFCLK IN
126 /TESTPIN1 IN
127 /SYNCEN OUT
128 SD10 IN/OUT
129 SD11 IN/OUT
130 SD12 IN/OUT
131 SD13 IN/OUT
132 SD14 IN/OUT
133 5V Power
134 SD15 IN/OUT
135 SD16 IN/OUT
136 GND Power
137 SD17 IN/OUT
138 SOE1 OUT
139 SWE1 OUT
Description
(Not used)
(Not used)
(Not used)
(Not used)
(Not used)
(Not used)
High: Normal Low: Test
Write clock
High: Normal Low: Test
Jitter adjustment IC trigger
signal
Data line to SRAM before are
separation
Data line to SRAM before are
separation
Data line to SRAM before are
separation
Read enable line to SRAM
before area separation
Write enable line to SRAM
before area separation
AL-1611/AL-1622 ELECTRICAL SECTION
13 – 7
PIN No. Signal Name IN/OUT
140 SCS1 OUT
141 SOE0 OUT
142 SWE0 OUT
143 SCS0 OUT
144 SD00 IN/OUT
145 SD01 IN/OUT
146 5V Power
147 SD02 IN/OUT
148 SD03 IN/OUT
149 GND Power
150 SD04 IN/OUT
151 SD05 IN/OUT
152 SD06 IN/OUT
153 SD07 IN/OUT
154 SAD0 OUT
155 SAD1 OUT
156 SAD2 OUT
157 SAD3 OUT
158 SAD4 OUT
159 SAD5 OUT
160 SAD6 OUT
161 SAD7 OUT
162 GND Power
163 SAD8 OUT
164 SAD9 OUT
165 SAD10 OUT
166 SAD11 OUT
167 SAD12 OUT
168 SAD13 OUT
169 /f1 OUT
170 /f2 OUT
171 /SH OUT
172 5V Power
173 RS OUT
174 SP OUT
175 GND Power
176 CP OUT
177 BCLK OUT
178 IDIN0 IN
179 IDIN1 IN
180 IDIN2 IN
181 IDIN3 IN
182 IDIN4 IN
183 IDIN5 IN
184 IDIN6 IN
Description
Chip select line to SRAM
before area separation
Read enable line to SRAM
before area separation
Write enable line to SRAM
before area separation
Chip select line to SRAM
before area separation
Data line to SRAM before are
separation
Data line to SRAM before are
separation
Data line to SRAM before are
separation
Address line to SRAM before
area separation
Address line to SRAM before
area separation
CCD drive signal transfer
clock (First phase)
CCD drive signal transfer
clock (Second phase)
CCD drive signal shift pulse
CCD drive signal reset pulse
CCD drive signal sampling
hold pulse
A/D conversion IC latch clock
CCD shield output latch sig-
nal
Image scan data (after 8bit A/
D conversion)