Ozito PLS-1214 Instruction Manual

Ozito PLS-1214 Instruction Manual

Plunge saw kit

Advertisement

PLUNGE
SAW KIT
1200W

INSTRUCTION MANUAL

SPECIFICATIONS

Motor:
1200W
Input:
230-240V ~ 50Hz
No Load Speed:
5,200/min
Blade Diameter:
165mm (6½")
Blade Bore:
20mm
Depth of Cut:
55mm @ 90°
42mm @ 45°
Guide Rail Length:
700mm
Weight:
4.65kg
ozito.com.au
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO
Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

WARRANTY

The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: O-rings, bearing,
seals gaskets.
WARNING
The following actions will result in the warranty being void.
• I f the tool has been operated on a supply voltage other
than that specified on the tool.
• I f the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• F ailure to perform maintenance as set out within the
instruction manual.
• I f the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WHAT'S IN THE BOX
Plunge Saw
Guide Rails x 2
Clamps x 2
Hex Keys (3 & 5mm) &
Joiner
PLS-1214
0117

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PLS-1214 and is the answer not in the manual?

Questions and answers

Ian Gilchrist
July 3, 2025

Can I purchase a blade retaining bolt Ozito PLS1214

Summary of Contents for Ozito PLS-1214

  • Page 1: Instruction Manual

    Clamps x 2 Hex Keys (3 & 5mm) & Joiner PLS-1214 WARRANTY IN ORDER TO MAKE A CLAIM UNDER THIS The benefits provided under this warranty are in addition to other rights and remedies which are available to you at law.
  • Page 2 KNOW YOUR PRODUCT SETUP & PREPARATION PLUNGE SAW 1. Hex Key Holder 6. Front Handle 1. DEPTH & BEVEL ADJUSTMENT 2. Dust Port 7. Rear Bevel Locking Knob 3. Safety Switch 8. Saw Blade WARNING! ENSURE THE TOOL IS SWITCHED OFF AND 4.
  • Page 3 OPERATION 2. CONTROLS 3. CUTTING GUIDES Cutting Line Guide WARNING! THE TOOL IS RECOMMENDED FOR USE WITH A RESIDUAL CURRENT DEVICE WITH A RATED RESIDUAL CURRENT OF 30mA OR LESS. Turning On and Off 1. Slide and hold the Safety Switch then squeeze the On/Off Trigger to start the saw.
  • Page 4 7. Move the saw through the material to perform the cut. 8. Once complete, release the on/off trigger and move the saw blade upwards. 7. Set the plunge saw to its original position. PLS-1214...
  • Page 5: Carbon Brushes

    Always replace both carbon brushes at the same time. replaced. Carbon brushes should only be replaced by a qualified Note: Ozito Industries will not be responsible for any damage or injuries electrician or power tool repairer. caused by the repair of the saw by an unauthorised person or by mishandling of the saw.
  • Page 6 Replace the extension lead if damaged or defective. Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand. When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and electric shock.

Table of Contents

Save PDF